UNT Libraries Government Documents Department - 5,157 Matching Results

Search Results

prev Results: 5065 - 5088 next
open access

Flight Tests to Determine the Effect of Length of a Conical Windshield on the Drag of a Bluff Body at Supersonic Speeds

Description: Flight tests were conducted to determine the effect of length of a conical windshield on the drag of a bluff body moving at supersonic speeds. A comparison is made between results obtained and results of previous drag tests of body-windshield combinations.The effect of increasing the length of the windshield is discussed.
Date: January 29, 1947
Creator: Alexander, Sidney R. & Katz, Ellis
Item Type: Refine your search to only Report
open access

The High-Speed Longitudinal Stability and Control of the Bell P-39N-1 Airplane as Calculated from Propeller-Off Tests of a 0.35-Scale Model

Description: "This report presents the result of tests of a 0.35-scale model of the Bell P-39N-l airplane. Included are the longitudinal-stability and - control characteristics of the airplane as indicated by tests of the model equipped with each of two different sets of elevators. The results indicate good longitudinal stability and control throughout the speed range encounterable in flight" (p. 1).
Date: January 29, 1947
Creator: Robinson, Robert C. & Perone, Angelo
Item Type: Refine your search to only Report
open access

The High-Speed Longitudinal Stability and Control of the Bell P-39N-1 Airplane as Calculated from Propeller-Off Tests of a 0.35-Scale Model

Description: "This report presents the results of tests of a .35-scale model of the Bell P-39N-1 airplane. Included are the longitudinal-stability and -control characteristics of the airplane as indicated by tests of the model equipped with each of two different sets of elevators. The results indicate good longitudinal stability and control throughout the speed range encounterable in flight" (p. 1).
Date: January 29, 1947
Creator: Robinson, Robert C. & Perone, Angelo
Item Type: Refine your search to only Report
open access

An Analysis of the Full-Floating Journal Bearing

Description: "An analysis of the operating characteristics of a full-floating bearing - a bearing in which a floating sleeve is located between the journal and bearing surfaces - is presented together with charts - from which the performance of such bearings may be predicted. Examples are presented to illustrate the use of these charts and a limited number of experiments conducted upon a glass full-floating bearing to verify some results of the analysis are reported. The floating sleeve can operate over a w… more
Date: January 28, 1947
Creator: Shaw, M. C. & Nussdorfer, T. J., Jr.
Item Type: Refine your search to only Report
open access

Theoretical Analysis and Bench Tests of a Control-Surface Booster Employing a Variable Displacement Hydraulic Pump

Description: From Summary: "The NACA is conducting a general investigation of servo-mechanisms for use in powering aircraft control surfaces. This paper presents a theoretical analysis and the results of bench tests of a control-booster system which employs a variable displacement hydraulic pump. The booster is intended for use in a flight investigation to determine the effects of various booster parameters on the handling qualities of airplanes. Such a flight investigation would aid in formulating specific… more
Date: January 28, 1947
Creator: Mathews, Charles W. & Kleckner, Harold F.
Item Type: Refine your search to only Report
open access

Theoretical investigation of thrust augmentation of turbojet engines by tail-pipe burning

Description: Report presenting a theoretical analysis of thrust augment of turbojet engines by tail-pipe burning and charts from which the thrust augmentation produced may be evaluated from the normal engine data and performance of the tail-pipe burner. Results regarding general curves and illustrative curves are provided.
Date: January 28, 1947
Creator: Bohanon, H. R. & Wilcox, E. C.
Item Type: Refine your search to only Report
open access

Investigations of Tumbling Characteristics of a 1/20-Scale Model of the Northrop N-9M Airplane

Description: From Summary: "The tumbling characteristics of a 1/20-scale model of the Northrop N-9M airplane have been determined in the Langley 20-foot free-spinning tunnel for various configurations and loading conditions of the model. The investigation included tests to determine whether recovery from a tumble could be effected by the use of parachutes. An estimation of the forces due to acceleration acting on the pilot during a tumble was made. The tests were performed at an equivalent test altitude of … more
Date: January 27, 1947
Creator: MacDougall, George F., Jr.
Item Type: Refine your search to only Report
open access

Estimated Flying Qualities of the Martin Model 202 Airplane

Description: The flying qualities of the Martin model 202 airplane have been estimated chiefly from the results of tests of an 0.0875-scale complete model with power made in the Wright Brothers tunnel at the Massachusetts Institute of Technology and from partial span wing and isolated vertical tail tests made in the Georgia Tech Nine-Foot Tunnel. These estimated handling qualities have been compared with existing Army-Navy and CAA requirements for stability and control.
Date: January 24, 1947
Creator: Weil, Joseph & Spear, Margaret
Item Type: Refine your search to only Report
open access

Drag Measurements at Transonic Speeds of NACA 65-009 Airfoils Mounted on a Freely Falling Body to Determine the Effects of Sweepback and Aspect Ratio

Description: From Summary: "Drag measurements at transonic speeds on rectangular airfoils and on airfoils swept back 450 are reported. These airfoils, which were mounted on cylindrical test bodies, are part of a series being tested in free drops from high altitude to determine the effect of variation of basic airfoil parameters on airfoil drag characteristics at transonic speeds. These rectangular and swept-back airfoils had the same span, airfoil section (NACA 65-009), and chord perpendicular to the leadin… more
Date: January 22, 1947
Creator: Mathews, Charles W. & Thompson, Jim Rogers
Item Type: Refine your search to only Report
open access

Effect of Exhaust Pressure on the Cooling Characteristics of a Liquid-Cooled Engine

Description: "Data for a liquid-cooled engine with a displacement volume of 1710 cubic inches were analyzed to determine the effect of exhaust pressure on the engine cooling characteristics. The data covered a range of exhaust pressures from 7 to 62 inches of mercury absolute, inlet-manifold pressures from 30 to 50 inches of mercury absolute, engine speeds from 1600 to 3000 rpm, and fuel-air ratios from 0.063 to 0.100. The effect of exhaust pressure on engine cooling was satisfactorily incorporated in the N… more
Date: January 22, 1947
Creator: Doyle, Ronald B. & Desmon, Leland G.
Item Type: Refine your search to only Report
open access

Performance of the 19XB 10-Stage Axial-Flow Compressor with Altered Blade Angles

Description: "Previous performance data of the 19XB axial-flow compressor indicated that the outlet guide vanes and possibly the inlet guide vanes were stalling. Calculations were made to determine if these adverse conditions could be eliminated and if the manufacturer's design specifications could be more nearly approached by altering the blade angles of the first few compression stages as well as the outlet guide vanes. With the blade angles altered, experimental data were taken at compressor speeds of 85… more
Date: January 22, 1947
Creator: Downing, Richard M.; Finger, Harold B. & Roepcke, Fay A.
Item Type: Refine your search to only Report
open access

Altitude-Wind-Tunnel Investigation of the 19B-2, 19B-8, and 19XB-1 Jet-Propulsion Engines 2 - Analysis of Turbine Performance of the 19B-8 Engine

Description: "Performance characteristics of the turbine in the 19B-8 jet propulsion engine were determined from an investigation of the complete engine in the Cleveland altitude wind tunnel. The investigation covered a range of simulated altitudes from 5000 to 30,000 feet and flight Mach numbers from 0.05 to 0.46 for various tail-cone positions over the entire operable range of engine speeds. The characteristics of the turbine are presented as functions of the total-pressure ratio across the turbine and th… more
Date: January 20, 1947
Creator: Krebs, Richard P. & Suozzi, Frank L.
Item Type: Refine your search to only Report
open access

Effects of Induction-System Icing on Aircraft-Engine Operating Characteristics

Description: "An investigation was conducted on a multicylinder aircraft engine on a dynamometer stand to determine the effect of induction-system icing on engine operating characteristics and to compare the results with those of a previous laboratory investigation in which only the carburetor and the engine-stage supercharger assembly from the engine were used. The experiments were conducted at simulated glide power, low cruise power, and normal rated power through a range of humidity ratios and air temper… more
Date: January 20, 1947
Creator: Stevens, Howard C., Jr.
Item Type: Refine your search to only Report
open access

Two-Dimensional Wind-Tunnel Investigation of Modified NACA 65(sub 112)-111 Airfoil with 35-Percent-Chord Slotted Flap at Reynolds Numbers up to 25 Million

Description: From Summary: "An investigation has been made in the Langley two-dimensional low-turbulence tunnels to develop the optimum configuration of a .035-chord slotted flap on an NACA 65(sub(112)-111 airfoil section modified by removing the trailing-edge cusp. Included in the investigation were measurements to determine the scale effects on the section lift and drag characteristics of the airfoil with the flap retracted for Reynolds numbers ranging from 3.0 X 10(exp 6) to 2.5 X 10(exp 6). The scale ef… more
Date: January 20, 1947
Creator: Racisz, Stanley F.
Item Type: Refine your search to only Report
open access

A Method for Predicting the Stability in Roll of Automatically Controlled Aircraft Based on the Experimental Determination of the Characteristics of an Automatic Pilot

Description: Report presenting a method for predicting the stability of automatically controlled aircraft by comparing the calculated frequency-response curves for the aircraft and experimentally determined frequency-response curves for the automatic pilot. The method is applicable only to stabilization in roll. It can be used to establish the specifications of performance required for the automatic control device for pilotless aircraft designed as missiles.
Date: January 17, 1947
Creator: Jones, Robert T. & Sternfield, Leonard
Item Type: Refine your search to only Report
open access

Performance of Compressor XJ-41-V Turbojet Engine 1 - Preliminary Investigation at Equivalent Compressor Speed of 8000 RPM

Description: From Summary: "At the request of the Air Material Command, Arm Air Forces, an investigation was conducted at the NACA Cleveland laboratory to determine the performance characteristics of the XJ-41-V turbojet-engine compressor. The complete compressor was mounted on a collecting chamber having an annular air-flow passage simulating the burner annulus of the engine and was driven by an electric motor. The compressor was extensively instrumented to determine the overall performance of the compress… more
Date: January 17, 1947
Creator: Ginsburg, Ambrose & Creagh, John W. R.
Item Type: Refine your search to only Report
open access

Altitude Cooling Investigation of the R-2800-21 Engine in the P-47G Airplane 4 - Engine Cooling-Air Pressure Distribution

Description: "A study of the data obtained in a flight investigation of an R-2800-21 engine in a P-47G airplane was made to determine the effect of the flight variables on the engine cooling-air pressure distribution. The investigation consisted of level flights at altitudes from 5000 to 35,000 feet for the normal range of engine and airplane operation. The data showed that the average engine front pressures ranged from 0.73 to 0.82 of the impact pressure (velocity head). The average engine rear pressures r… more
Date: January 16, 1947
Creator: Kaufman, Samuel J.; Staudt, Robert C. & Valerino, Michael F.
Item Type: Refine your search to only Report
open access

A Device for Measuring Sonic Velocity and Compressor Mach Number

Description: "A device has been developed which measures the velocity of sound in fluids at stagnation and is especially adaptable to turbine and compressor testing for which the constituency of the working fluid may be in doubt. By utilizing the shaft frequency of a rotary compressor, the instrument can also be used to provide a direct measurement of the compressor Mach number (ratio of blade-tip velocity to inlet velocity of sound at stagnation). A Helmholtz resonator is employed in the measurement of the… more
Date: January 16, 1947
Creator: Huber, Paul W. & Kantrowitz, Arthur
Item Type: Refine your search to only Report
open access

Effect of Modifications to Induction System on Altitude Performance of V-1710-93 Engine 3: Use of Parabolic Rotating Guide Vanes and NACA Designed Auxiliary-Stage Inlet Elbow and Interstage Duct

Description: "Bench runs of a modified V-1710-93 engine equipped with a two-stage supercharger, interstage carburetor, aftercooler assembly, and backfire screens have been made at a simulated altitude of 29,000 feet to determine the effect of several induction-system modifications on the engine and supercharger performance. The standard guide vanes on the auxiliary- and engine-stage superchargers were replaced by rotating guide vanes with a parabolic blade profile. The auxiliary-stage inlet elbow and inters… more
Date: January 16, 1947
Creator: Standahar, Ray M. & McCarty, James S.
Item Type: Refine your search to only Report
open access

[Memorandums on the Subject of D-558 Airplane]

Description: "An investigation of the air-stream fluctuations at the tail of the D-558-1 airplane has been made at high speed for the purpose of determining the vertical region in which the horizontal tail may be placed without becoming subject to tail buffeting. The investigation was made for a range of Mach numbers from 0.775 to 0.907, and a range of vertical positions at the tall to include two proposed horizontal-tail positions. The tests were made at two angles of attack, 0,2 deg. and 4.2 deg., represe… more
Date: January 16, 1947
Creator: Pendley, Robert E.
Item Type: Refine your search to only Report
open access

Wind-Tunnel Tests of a 1/4-Scale Model of the Naval Aircraft Factory Float-Wing Convoy Interceptor, TED No. NACA 2314

Description: A 1/4 - scale model of the Naval Aircraft Factory float-wing convoy interceptor was tested in the Langley 7-by 10-foot tunnel to determine the longitudinal and lateral stability characteristics. The model was tested in the presence of a ground board to determine the effect of simulating the ground on the longitudinal characteristics.
Date: January 16, 1947
Creator: Wells, Evalyn G. & McKinney, Elizabeth G.
Item Type: Refine your search to only Report
open access

Preliminary Tests of a Burner for Ram-Jet Applications

Description: "Preliminary tests have been made of a small burner to meet the requirements for application to supersonic ram jets. The principal requirements were taken as: (1) efficient combustion in a high-velocity air stream, (2) utilization for combustion of only a small fraction of the air passing through the unit, (3) low resistance to air flow, (4) simple construction, and (5) light weight. Tests of a small burner were carried to stream velocities of nearly 150 feet per second and fuel rates such that… more
Date: January 15, 1947
Creator: Huber, Paul W.
Item Type: Refine your search to only Report
open access

Results of Tests to Determine the Effect of a Conical Windshield on the Drag of a Bluff Body at Supersonic Speeds

Description: Tests to evaluate the effect of a conical windshield on the drag of a bluff body at supersonic speeds were performed for the following configurations: a sharp nose fuselage with stabilizing fins,a blunt nose fuselage with a hemispherical shape, and a blunt nose fuselage with a conical point. Results of the drag coefficient are described at Mach 1.0 and the greatest Mach number of 1.37.
Date: January 14, 1947
Creator: Alexander, Sidney R.
Item Type: Refine your search to only Report
open access

Performance Investigation of TG-180 Combustor: 1 - Instrumentation, Altitude Operational Limits and Combustion Efficiency

Description: A brief investigation has been made of the performance of a single combustor of the TG-180 turboJet engine to determine (a) the altitude operational limits of the engine for two fuels (AN-F-32 and AN-F-28), (b) combustion efficiencies at various simulated conditions of altitude and engine speeds, (c) combustion-outlet temperature distribution for several altitudes at constant engine speed, and (d) the combustor total pressure drop The limits with AN-83-F-32 fuel were found to be approximately 6… more
Date: January 13, 1947
Creator: Zettle, Eugene V. & Cook, William P.
Item Type: Refine your search to only Report
Back to Top of Screen