You limited your search to:

  Partner: UNT Libraries Government Documents Department
 Language: English
 Serial/Series Title: NACA Special Report
 Collection: Technical Report Archive and Image Library
Performance Characteristics of an Aircraft Engine with Exhaust Turbine Supercharger, Special Report

Performance Characteristics of an Aircraft Engine with Exhaust Turbine Supercharger, Special Report

Date: May 1, 1941
Creator: Lester, E. M. & Paulson, V. A.
Description: The Pratt and Whitney Aircraft company and the Naval Aircraft Factory of the United States Navy cooperated in a laboratory and flight program of tests on an exhaust turbine supercharger. Two series of dynamometer tests of the engine super-charger combination were completed under simulated altitude conditions. One series of hot gas-chamber tests was conducted by the manufacturer of the supercharger. Flight demonstrations of the supercharger installed in a twin-engine flying boat were terminated by failure of the turbine wheels. The analysis of the results indicated that a two-stage supercharger with the first-stage exhaust turbine driven will deliver rated power for a given indicated power to a higher altitude, will operate more efficiently, and will require simpler controls than a similar engine with the first stage of the supercharger driven from the crankshaft through multispeed gears.
Contributing Partner: UNT Libraries Government Documents Department
Tandem Air Propellers

Tandem Air Propellers

Date: August 1, 1937
Creator: Lesley, E.P.
Description: Tests of 2-blade, adjustable-pitch, counterrotating tandem model propellers, adjusted to absorb equal power at maximum efficiency, were made at Stanford University. The characteristics, for 15 degrees, 25 degrees, 35 degrees, and 45 degrees pitch settings at 0.75 R of the forward propeller and for 8 1/2%, 15% and 30% diameter spacings, were compared with those of 2-blade and 4-blade propellers of the same blade form. The tests showed that the efficiency of the tandem propellers was from 0.5% to 4% greater than that of a 4-blade propeller and, at the high pitch settings, not appreciable inferior to that of a 2-blade propeller. It was found that the rear tandem propeller should be set at a pitch angle slightly less than that of the forward propeller to realize the condition of equal power at maximum efficiency. Under this condition the total power absorbed by the tandem propellers was from 3% to 9% more than that absorbed by the 4-blade propeller and about twice that absorbed by a 2-blade propeller.
Contributing Partner: UNT Libraries Government Documents Department
Tandem Air Propellers - II

Tandem Air Propellers - II

Date: October 1, 1939
Creator: Lesley, E. P.
Description: Tests of three-blade, adjustable-pitch counterrotating tandem model propellers, adjusted to absorb equal power at maximum efficiency of the combination, were made at Stanford University. The aerodynamic characteristics, for blade-angle settings of 15, 25, 35, 45, 55, and 65 degrees at 0.75R of the forward propeller and for diameters spacings of 8-1/2, 15 and 30% were compared with those of three-blade and six-blade propellers of the same blade form. It was found that, in order to realize the condition of equal power at maximum efficiency, the blade angles for the rear propeller must be generally less than for the forward propeller, the difference increasing the blade angle. The tests showed that, at maximum efficiency, the tandem propellers absorb about double the power of three-blade propellers and about 8% more power than six-blade propellers having the pitch of the forward propeller of the tandem combination. The maximum efficiency of the tandem propellers was found to be from 2-15% greater than for six-blade propellers, the difference varying directly with blade angle. It was also found that the maximum efficiency of the tandem propellers was greater than that of a three-blade propeller for blade angles at 0.75R of 25 degrees or more. The difference ...
Contributing Partner: UNT Libraries Government Documents Department
Propeller-Design Problems of High-Speed Airplanes, Special Report

Propeller-Design Problems of High-Speed Airplanes, Special Report

Date: April 1, 1941
Creator: Dickinson, H. B.
Description: It is shown that on the basis of existing high-speed airfoil data, propeller efficiencies appreciably in excess of 40% do not appear possible at speeds above 500 miles per hour at 20,000 feet. The assumption that present propeller-blade thicknesses cannot be reduced radically, is implied. Until the reliability and applicability of the airfoil data are established, this conclusion must not be regarded as infallible. Dive tests with airplanes equipped with thrust meters and torque meters are proposed to provide an urgently needed check. The design of high-speed propellers is dictated wholly by compressibility considerations. The blade width, thickness, and pitch distribution; also the airfoil sections, the lift coefficient, the propeller diameter, and rpm must all be adjusted if reasonable efficiencies are to be maintained at airplane speeds that are now being approached. Research is urgently needed on: 1) airfoils at subsonic, sonic, and supersonic speeds; 2) propellers at high forward speeds in wind tunnels; 3)propellers in free flight at high speeds; and 4) jet propulsion and related devices. The breakdown of propeller efficiency indicated by airfoil data, should serve as an incentive for accelerated research on jet propulsion. This device may extend the attainable speed of current airplanes to the ...
Contributing Partner: UNT Libraries Government Documents Department
Wind-Tunnel Development of Ailerons for the Curtiss XP-60 Airplanem Special Report

Wind-Tunnel Development of Ailerons for the Curtiss XP-60 Airplanem Special Report

Date: September 1, 1942
Creator: Rogallo, F. M. & Lowry, John G.
Description: An investigation was made in the LWAL 7- by 10-foot tunnel of internally balanced, sealed ailerons for the Curtiss XP-60 airplane. Ailerons with tabs and. with various amounts of balance were tested. Stick forces were estimated for several aileron arrangements including an arrangement recommended for the airplane. Flight tests of the recommended arrangement are discussed briefly in an appendix, The results of the wind-tunnel and flight tests indicate that the ailerons of large or fast airplanes may be satisfactorily balanced by the method developed.
Contributing Partner: UNT Libraries Government Documents Department
Wing-Nacelle-Propeller Tests - Comparative Tests of Liquid-Cooled and Air-Cooled Engine Nacelles

Wing-Nacelle-Propeller Tests - Comparative Tests of Liquid-Cooled and Air-Cooled Engine Nacelles

Date: January 1, 1934
Creator: Wood, Donald H.
Description: This report gives the results of measurements of the lift, drag, and propeller characteristics of several wing and nacelle combinations with a tractor propeller. The nacelles were so located that the propeller was about 31% of the wing chord directly ahead of the leading edge of the wing, a position which earlier tests (NASA Report No. 415) had shown to be efficient. The nacelles were scale models of an NACA cowled nacelle for a radial air-cooled engine, a circular nacelle with the V-type engine located inside and the radiator for the cooling liquid located inside and the radiator for the type, and a nacelle shape simulating the housing which would be used for an extension shaft if the engine were located entirely within the wing. The propeller used in all cases was a 4-foot model of Navy No. 4412 adjustable metal propeller. The results of the tests indicate that, at the angles of attack corresponding to high speeds of flight, there is no marked advantage of one type of nacelle over the others as far as low drag is concerned, since the drag added by any of the nacelles in the particular location ahead of the wing is very small. ...
Contributing Partner: UNT Libraries Government Documents Department
Wind-Tunnel Investigation of Rectangular Air-Duct Entrances in the Leading Edge of an NACA 23018 Wing, Special Report

Wind-Tunnel Investigation of Rectangular Air-Duct Entrances in the Leading Edge of an NACA 23018 Wing, Special Report

Date: September 1, 1940
Creator: Biermann, David & McLellan, Charles H.
Description: A preliminary investigation of a number of duct entrances of rectangular shape installed in the leading edge of a wing was conducted in the NACA 20-foot tunnel to determine the external drag, the available pressure, the critical Mach numbers, and the effect on the maximum lift. The results showed that the most satisfactory entrances, which had practically no effect on the wing characteristics, had their lips approximately in the vertical plane of the leading edge of the wing. This requirement necessitated extending the lips outside the wing contour for all except the small entrances. Full dynamic pressure was found to be available over a fairly wide range of angle of attack. The critical Mach number for a small entrance was calculated to be as high as that for the plain wing but was slightly lower for the larger entrances tested.
Contributing Partner: UNT Libraries Government Documents Department
Preliminary Investigation of the Effect of Compressibility on the Maximum Lift Coefficient, Special Report

Preliminary Investigation of the Effect of Compressibility on the Maximum Lift Coefficient, Special Report

Date: February 1, 1943
Creator: Stack, John; Fedziuk, Henry A. & Cleary, Harold E.
Description: Preliminary data are presented on the variation of the maximum lift coefficient with Mach number. The data were obtained from tests in the 8-foot high-speed tunnel of three NACA 16-series airfoils of 1-foot chord. Measurements consisted primarily of pressure-distribution measurements in order to illustrate the nature of the phenomena. It was found that the maximum lift coefficient of airfoils is markedly affected by compressibility even at Mach numbers as low as 0.2. At high Mach numbers pronounced decrease of the maximum lift coefficient was found. The magnitude of the effects of compressibility on the maximum lift coefficient and the low speeds at which these effects first appear indicate clearly that consideration of the take-off thrust for propellers will give results seriously in error if these considerations are based on the usual low-speed maximum-lift-coefficient data generally used.
Contributing Partner: UNT Libraries Government Documents Department
Preliminary Wind-Tunnel Tests of the Effect of Nacelles on the Characteristics of a Twin-Engine Bomber Model with Low-Drag Wing, Special Report

Preliminary Wind-Tunnel Tests of the Effect of Nacelles on the Characteristics of a Twin-Engine Bomber Model with Low-Drag Wing, Special Report

Date: July 1, 1942
Creator: Wenzinger, Carl J. & Sivells, James C.
Description: Tests were made in the NACA 19-foot pressure tunnel of a simplified twin-engine bomber model with an NACA low-drag wing primarily to obtain an indication of the effects of engine nacelles on the characteristics of the model both with and without simple split trailing-edge flaps. Nacelles with conventional-type cowlings representative of those used on an existing high-performance airplane and with NACA high-speed type E cowlings were tested. The tests were made without propeller slipstream. The aerodynamic effects of adding the nacelles to the low-drag wing were similar to the effects commonly obtained by adding similar nacelles to conventional wings. The maximum lift coefficient without flaps was slightly increased, but the increment in maximum lift due to deflecting the flaps was somewhat decreased. The stalling characteristics were improved by the presence of the nacelles. Addition of the nacelles had a destabilizing effect on the pitching moments, as is usual for nacelles that project forward of the wing. The drag increments due to the nacelles were of the usual order of magnitude, with the increment due to the nacelles with NACA type E cowlings approximately one-third less than that of the nacelles with conventional cowlings with built-in air scoops.
Contributing Partner: UNT Libraries Government Documents Department
Restraint Provided a Flat Rectangular Plate by a Sturdy Stiffener Along an Edge of the Plate, Special Report

Restraint Provided a Flat Rectangular Plate by a Sturdy Stiffener Along an Edge of the Plate, Special Report

Date: May 1, 1941
Creator: Lundquist, Eugene E. & Stowell, Elbridge Z.
Description: A sturdy stiffener is defined as a stiffener of such proportions that it does not suffer cross-sectional distortion when moments are applied to some part of the cross section. When such a stiffener is attached to one edge of a plate, it will resist rotation of that edge of the plate by means of its torsional properties. A formula is given for the restraint coefficient provided the plate by such a stiffener. This coefficient is required for the calculation of the critical compressive stress of the plate.
Contributing Partner: UNT Libraries Government Documents Department
A Remote Indicating Hinge-Moment Balance, Special Report

A Remote Indicating Hinge-Moment Balance, Special Report

Date: August 1, 1941
Creator: Stoller, Morton J. & Ribner, Herbert S.
Description: This report describes an electrical hinge-moment balance for use with wind-tunnel models of aircraft. A brief description of the principle of operation and operating experience with the balance is given in part I. Part II gives constructional details and part III gives theoretical considerations. Extensive constructional information is given to enable the reproduction of the equipment.
Contributing Partner: UNT Libraries Government Documents Department
Wind-Tunnel Investigation of the Lift Characteristics of an NACA 27-212 Airfoil Equipped with Two Types of Flap, Special Report

Wind-Tunnel Investigation of the Lift Characteristics of an NACA 27-212 Airfoil Equipped with Two Types of Flap, Special Report

Date: September 1, 1940
Creator: Swanson, Robert S. & Schuldenfrei, Marvin J.
Description: An investigation has been made in the NACA 7- by 10-foot wind tunnel of a large chord NACA 27-212 airfoil with a 20% chord split flap and with two arrangements of a 25.66% chord slotted flap to determine the section lift characteristics as affected by flap deflection for the split flap and as affected by flap deflection, flap position, and slot shape for the slotted flap. For the two arrangements of the slotted flap, the flap positions for maximum section lift are given. Comparable data on the NACA 23012 airfoil equipped with similar flaps are also given. On the basis of maximum section lift coefficient, the slotted flap with an easy slot entry was slightly better than either the split flap or the slotted flap with a sharp slot entry. With both types of flap the decrease in the angle of attack, for maximum section lift coefficient, with flap deflection is large for the NACA 27-212 airfoil as compared with the NACA 23012 airfoil. Also with both flaps, the maximum section lift coefficient obtained with flaps is much lower for the NACA 27-212 airfoil than for the NACA 23012 airfoil.
Contributing Partner: UNT Libraries Government Documents Department
Comparison of Three Exit-Area Control Devices on an N.A.C.A. Cowling, Special Report

Comparison of Three Exit-Area Control Devices on an N.A.C.A. Cowling, Special Report

Date: May 1, 1940
Creator: McHugh, James G.
Description: Adjustable cowling flaps, an adjustable-length cowling skirt, and a bottom opening with adjustable flap were tested as means of controlling the rate of cooling-air flow through an air-cooled radial-engine cowling. The devices were tested in the NACA 20-foot tunnel on a model wing-nacelle-propeller combination, through an airspeed range of 20 to 80 miles per hour, and with the propeller blade angle set 23 degrees at 0.75 of the tip radius. The resistance of the engine to air flow through the cowling was simulated by a perforated plate. The results indicated that the adjustable cowling flap and the bottom opening with adjustable flap were about equally effective on the basis of pressure drop obtainable and that both were more effective means of increasing the pressure drop through the cowling than the adjustable-length skirt. At conditions of equal cooling-air flow, the net efficiency obtained with the adjustable cowling flaps and the adjustable-length cowling skirt was about 1% greater than the net efficiency obtained with the bottom opening with adjustable flap.
Contributing Partner: UNT Libraries Government Documents Department
Tests of Wing Machine-Gun and Cannon Installations in the NACA Full-Scale Wind Tunnel, Special Report

Tests of Wing Machine-Gun and Cannon Installations in the NACA Full-Scale Wind Tunnel, Special Report

Date: August 1, 1941
Creator: Czarnecki, K. R. & Guryansky, Eugene R.
Description: At the request of the Bureau of Aeronautics, an investigation was conducted in the full-scale wind tunnel of wing installations of .50-caliber machine guns and 20-millimeter cannons. The tests were made to determine the effect of various gun installations on the maximum lift and the high-speed drag of the airplane.
Contributing Partner: UNT Libraries Government Documents Department
Wind-tunnel Tests of the NACA 45-125 Airfoil: A Thick Airfoil for High-Speed Airplanes

Wind-tunnel Tests of the NACA 45-125 Airfoil: A Thick Airfoil for High-Speed Airplanes

Date: February 1, 1940
Creator: Delano, James B.
Description: Investigations of the pressure distribution, the profile drag, and the location of transition for a 30-inch-chord 25-percent-thick N.A,C.A. 45-125 airfoil were made in the N.A.C.A 8-foot high-speed wind tunnel for the purpose of aiding in the development of a thick wing for high-speed airplanes. The tests were made at a lift coefficient of 0.1 for Reynolds Numbers from 1,750,000 to 8,690,000, corresponding to speeds from 80 to 440 miles per hour at 59 F. The effect on the profile drag of fixing the transition point was also investigated. The effect of compressibility on the rate of increase of pressure coefficients was found to be greater than that predicted by a simplified theoretical expression for thin wings. The results indicated that, for a lift coefficient of 0.1, the critical speed of the N.A.C,A. 45-125 airfoil was about 460 miles per hour at 59 F,. The value of the profile-drag coefficient at a Reynolds Number of 4,500,000 was 0.0058, or about half as large as the value for the N.A,C,A. 0025 airfoil. The increase in the profile-drag coefficient for a given movement of the transition point was about three times as large as the corresponding increase for the N.A.C,A. 0012 airfoil. Transition ...
Contributing Partner: UNT Libraries Government Documents Department
Comparison of Intercooler Characteristics

Comparison of Intercooler Characteristics

Date: May 1, 1941
Creator: Reuter, J. George & Valerino, Michael F.
Description: A method is presented of comparing the performance, weight, and general dimensional characteristics of inter-coolers. The performance and dimensional characteristics covered in the comparisons are cooling effectiveness, pressure drops and weight flows of the charge and cooling air, power losses, volume, frontal area, and width. A method of presenting intercooler data is described in which two types of charts are plotted; (1) A performance chart setting forth all the important characteristics of a given intercooler and (2) a replot of these characteristics for a number of intercoolers intended to assist in making a selection to satisfy a given set of installation conditions. The characteristics of commercial intercoolers obtained from manufacturers' data and of some computed designs are presented on this basis. A standard test procedure and instrumentation are suggested whereby comparable data may be obtained by different testing organizations.
Contributing Partner: UNT Libraries Government Documents Department
Compressibility Effects in Aeronautical Engineering

Compressibility Effects in Aeronautical Engineering

Date: August 1, 1941
Creator: Stack, John
Description: Compressible-flow research, while a relatively new field in aeronautics, is very old, dating back almost to the development of the first firearm. Over the last hundred years, researches have been conducted in the ballistics field, but these results have been of practically no use in aeronautical engineering because the phenomena that have been studied have been the more or less steady supersonic condition of flow. Some work that has been done in connection with steam turbines, particularly nozzle studies, has been of value, In general, however, understanding of compressible-flow phenomena has been very incomplete and permitted no real basis for the solution of aeronautical engineering problems in which.the flow is likely to be unsteady because regions of both subsonic and supersonic speeds may occur. In the early phases of the development of the airplane, speeds were so low that the effects of compressibility could be justifiably ignored. During the last war and immediately after, however, propellers exhibited losses in efficiency as the tip speeds approached the speed of sound, and the first experiments of an aeronautical nature were therefore conducted with propellers. Results of these experiments indicated serious losses of efficiency, but aeronautical engineers were not seriously concerned at the ...
Contributing Partner: UNT Libraries Government Documents Department
Engine Operation in Flight for Minimum Fuel Consumption

Engine Operation in Flight for Minimum Fuel Consumption

Date: November 1, 1939
Creator: Reuter, George
Description: Engine and airplane performance data have been gathered from various sources and analyzed to determine indications of the most economical methods of flight operation from a consideration of fuel expenditure. The analysis includes the influence of such facts as fuel-air ratio, engine speed, engine knock, altitude, cylinder cooling, spark timing, and limits of cruising brake mean effective pressure. The results indicate that the cheapest power is obtained with approximately correct mixture at low engine speed and highest permissible manifold pressure. If more power is desired, the methods of obtaining it are, in order of fuel economy: (a) increasing the engine speed and maintaining safe cylinder temperatures by cooling; (b) retarding the spark or cooling further to permit higher manifold pressure; and, (c) riching the mixture. The analysis further shows that the maximum time endurance of flight occurs at the air speed corresponding to minimum thrust horsepower required and with minimum practicable engine speed. Maximum mileage per pound of fuel is obtained at slightly higher air speed. The fuel-air ratio should be approximately the theoretically correct ratio in both cases. For an engine equipped with a geared supercharger, as in the example presented, and with knock as the limiting condition, a ...
Contributing Partner: UNT Libraries Government Documents Department
Experiments on the Recovery of Waste Heat in Cooling Ducts, Special Report

Experiments on the Recovery of Waste Heat in Cooling Ducts, Special Report

Date: May 1, 1939
Creator: Silverstein, Abe
Description: Tests have been conducted in the N.A.C.A. full-scale wind tunnel to investigate the partial recovery of the heat energy which is apparently wasted in the cooling of aircraft engines. The results indicate that if the radiator is located in an expanded duct, a part of the energy lost in cooling is recovered; however, the energy recovery is not of practical importance up to airplane speeds of 400 miles per hour. Throttling of the duct flow occurs with heated radiators and must be considered in designing the duct outlets from data obtained with cold radiators in the ducts.
Contributing Partner: UNT Libraries Government Documents Department
Investigation of an Electrically Heated Airplane Windshield for Ice Prevention, Special Report

Investigation of an Electrically Heated Airplane Windshield for Ice Prevention, Special Report

Date: March 1, 1939
Creator: Rodert, Lewis A.
Description: A study was made at the National Advisory Committee for Aeronautics Laboratory of the operation of an electrically heated glass panel, which simulated a segment of an airplane windshield, to determine if ice formations, which usually result in the loss of visibility, could be prevented. Tests were made in the 7- by 3-foot ice tunnel, and in flight, under artificially created ice-forming conditions. Ice was prevented from forming on the windshield model in the tunnel by 1.25 watts of power per square inch with the air temperature at 23 F and a velocity of 80 miles per hour. Using an improved model in flight, ice was prevented by 1.43 watts of power per square inch of protected area and 2 watts per inch concentrated in the rim, with the air temperature at 26 F and a velocity of 120 miles per hour. The removal of a preformed ice cap was effected to a limited extent in the tunnel by the use of 1.89 watts of power per square inch when the temperature and velocity were 25 F and 80 miles per hour, respectively. The results indicate that service tests with an improved design are justified.
Contributing Partner: UNT Libraries Government Documents Department
Large-Scale Boundary-Layer Control Tests on Two Wings in the NACA 20-Foot Wind Tunnel, Special Report

Large-Scale Boundary-Layer Control Tests on Two Wings in the NACA 20-Foot Wind Tunnel, Special Report

Date: April 1, 1935
Creator: Freeman, Hugh B.
Description: Tests were made in the N.A.C.A. 20-foot wind tunnel on: (1) a wing, of 6.5-foot span, 5.5-foot chord, and 30 percent maximum thickness, fitted with large end plates and (2) a 16-foot span 2.67-foot chord wing of 15 percent maximum thickness to determine the increase in lift obtainable by removing the boundary layer and the power required for the blower. The results of the tests on the stub wing appeared more favorable than previous small-scale tests and indicated that: (1) the suction method was considerably superior to the pressure method, (2) single slots were more effective than multiple slots (where the same pressure was applied to all slots), the slot efficiency increased rapidly for increasing slot widths up to 2 percent of the wing chord and remained practically constant for all larger widths tested, (3) suction pressure and power requirements were quite low (a computation for a light airplane showed that a lift coefficient of 3.0 could be obtained with a suction as low as 2.3 times the dynamic pressure and a power expenditure less than 3 percent of the rated engine power), and (4) the volume of air required to be drawn off was quite high (approximately 0.5 cubic ...
Contributing Partner: UNT Libraries Government Documents Department
Tests of Airfoils Designed to Delay the Compressibility Burble

Tests of Airfoils Designed to Delay the Compressibility Burble

Date: June 1, 1939
Creator: Stack, John
Description: Development of airfoil sections suitable for high-speed applications has generally been difficult because little was known of the flow phenomenon that occurs at high speeds. A definite critical speed has been found at which serious detrimental flow changes occur that lead to serious losses in lift and large increases in drag. This flow phenomenon, called the compressibility burble, was originally a propeller problem, but with the development of higher speed aircraft serious consideration must be given to other parts of the airplane. Fundamental investigations of high-speed airflow phenomenon have provided new information. An important conclusion of this work has been the determination of the critical speed, that is, the speed at which the compressibility burble occurs. The critical speed was shown to be the translational velocity at which the sum of the translational velocity and the maximum local induced velocity at the surface of the airfoil or other body equals the local speed of sound. Obviously then higher critical speeds can be attained through the development of airfoils that have minimum induced velocity for any given value of the lift coefficient. Presumably, the highest critical speed will be attained by an airfoil that has uniform chordwise distribution of induced velocity ...
Contributing Partner: UNT Libraries Government Documents Department
Wind-Tunnel Investigation of an NACA Low-Drag Tapered Wing with Straight Trailing Edge and Simple Split Flaps, Special Report

Wind-Tunnel Investigation of an NACA Low-Drag Tapered Wing with Straight Trailing Edge and Simple Split Flaps, Special Report

Date: December 1, 1941
Creator: Muse, Thomas C. & Neely, Robert H.
Description: An investigation was conducted in the NACA 19-foot pressure wind tunnel of a tapered wing with straight railing edge having NACA 66 series low-drag airfoil sections and equipped with full-span and partial-span simple split flaps. The airfoil sections used were the NACA 66,2-116 at the root and the 66,2-216 at the tip. The primary purpose of the investigation was to determine the effect of the split flaps on the aerodynamic characteristics of the tapered wing. Complete lift, drag, and pitching-moment coefficients were determined for the plain wing and for each flap arrangement through a Reynold number range of 2,600,000 to 4,600,000. The results of this investigation indicate that values of maximum lift coefficient comparable to values obtained on tapered wings with conventional sections and similar flap installations can be obtained from wings with the NACA low-drag sections. The increment of maximum lift due to the split flap was found to vary somewhat with Reynold number over the range investigated. The C(sub L)max of the wing alone is 1.49 at a Reynolds number of 4,600,000; whereas with the partial-span simple split flap it is 2.22 and with the full-span arrangement, 2.80. Observations of wool tufts on the wing indicate that the ...
Contributing Partner: UNT Libraries Government Documents Department
Wind-Tunnel Investigation of Air Inlet and Outlet Openings for Aircraft, Special Report

Wind-Tunnel Investigation of Air Inlet and Outlet Openings for Aircraft, Special Report

Date: October 1, 1938
Creator: Rogallo, Francis M. & Gauvain, William E.
Description: An investigation was made in the NACA 5-foot vertical wind tunnel of a large variety of duct inlets and outlets to obtain information relative to their design for the cooling or the ventilation systems on aircraft. Most of the tests were of openings in a flat plate but, in order to determine the best locations and the effects of interference, a few tests were made of openings in an airfoil. The best inlet location for a system not including a blower was found to be at the forward stagnation point; for one including a blower, the best location was found to be in the region of lowest total head, probably in the boundary layer near the trailing edge. Design recommendations are given, and it is shown that correct design demands a knowledge of the external flow and of the internal requirements in addition to that obtained from the results of the wind tunnel tests.
Contributing Partner: UNT Libraries Government Documents Department
FIRST PREV 1 2 3 4 5 NEXT LAST