UNT Libraries Government Documents Department - 116 Matching Results
Search Results
- Flight Investigation at High Mach Numbers of Several Methods of Measuring Static Pressure on an Airplane Wing
- Report discusses an investigation into static pressures in subsonic and supersonic flow over an airplane wing as measured by static-pressure tubes, a static-pressure belt, and orifices flush with the wing surface. The results obtained from the three types of measuring devices and a comparison to theoretical calculations are presented.
- Calculation of tab characteristics for flight conditions from wind-tunnel data
- Report presenting tail-surface characteristics calculated from wind-tunnel data, which have been reported to not correspond with flight-test measurements. The primary problem under consideration is the calculation of the effect of tab deflection on the free-floating angle of the elevator, as in a servocontrol.
- Some Effects of Propeller Operation on the Distribution of the Load on the Vertical Tail Surface of a Typical Pursuit Airplane
- Report discusses the results of testing on the pressure distribution at several longitudinal sections of the vertical tail surface of the Curtiss P-40K airplane at various angles of attack and angles of yaw and with the propeller removed and propeller operating. Results regarding the chordwise pressure distributions, effects of propeller operation on the spanwise distribution of normal-force coefficient, total normal-force coefficients, and effect of propeller operation on the variation of vertical-tail normal-force coefficients are presented.
- Maximum Rates of Control Motion Obtained From Ground Tests
- Report discusses the results of testing to determine the maximum rates of control stick (elevator) motion and corresponding maximum stick forces that could be exerted based on experiments with several pilots. The main topics explored were the comparison of the maximum rates of push and pull, maximum rates of push and pull when a mental restriction was placed on the pilot, and maximum rates at which the pilot though he would apply the elevator control forces versus the actual application of forces. Information about experimental procedures and the rig the testing occurred on is included.
- An Automatically Variable Control Linkage and Its Effect on the Lateral-Control Characteristics of a High-Speed Fighter Airplane
- Report discusses an analysis and preliminary design of a control linkage that varies automatically with dynamic pressure. The advantages of the device, including greater lateral control than a fixed control linkage without additional aerodynamic balance, are detailed. The effect of variable linkage on lateral-control characteristics is also described.
- Resume of Hinge-Moment Data for Unshielded Horn- Balanced Control Surfaces
- Report summarizes the available hinge-moment data for unshielded horn-balanced control surfaces. The purpose is to correlate the available data to assist with estimating the balance characteristics for use in the design and alteration of control surfaces with horn balances. Plan forms and variation of incremental hinge-moment-coefficient slopes with balance coefficients are presented.
- Calculation of Stick Forces for an Elevator With a Spring Tab
- "Formulas for the calculation of hinge-moment characteristics of an elevator with a spring tab have been developed in terms of basic aerodynamic parameters, spring stiffness, and airspeed. The formulas have been used in a study of the stick-force gradients on a pursuit airplane equipped with an elevator with a spring tab. Charts are presented showing the variation of stick-force gradient in accelerated flight over a large range of speed and the complete range of spring stiffness for various center-of-gravity locations, altitudes, and airplane sizes" (p. 1).
- Use of Variable-Ratio Geared Tabs to Improve Stick-Force Characteristics in Turning Flight
- Report discussing the use of variable-ratio geared tabs with an experimental elevator to improve stick-force characteristics in turning flight. The stick forces with the tabs were found to be satisfactory for a variety of center-of-gravity ranges. The ability of pilots to use the controls is also described.
- A Study of the Effects of Radii of Gyration and Altitude on Aileron Effectiveness at High Speed
- "The variation in the necessary aileron control and in the time required to bank to 45 degrees and 90 degrees with altitude and radii of gyration for a typical fighter or a pursuit airplane have been computed and are presented herein." The lateral motions and impact pressure for several conditions of flight are provided. The report concludes that "the aileron system...should be designed for rolling-moment requirements at high altitude and the hinge-moment limitations at low altitude".
- Adjustment of Stick Force by a Nonlinear Aileron-Stick Linkage
- Report presenting an application of the principle of aileron-stick forces and mechanical advantage to an aileron installation in which the stick forces are small over the low-deflection range and excessively large at full deflection.
- Application of Balancing Tabs to Ailerons
- Analysis was made to determine characteristics required of a balancing-tab system for ailerons in order to reduce aileron stick forces to any desired magnitude. Series of calculations based on section data were made to determine balancing-tab systems of various chord tabs and ailerons that will give, for a particular airplane, zero rate of aileron hinge moment with aileron deflection and yet will produce same maximum rate of roll as a plain unbalanced 15-percent chord aileron of same span. Effects of rolling velocity and of forces in tab link on aileron hinge moments have been included.
- NACA Procedure for Flight Tests of Aileron Characteristics of Airplanes
- Report describes the standard procedure that NACA used for evaluating the aileron characteristics of airplanes. The variables measured in the testing are rolling velocity, aileron positions, aileron stick forces or tangential wheel force, indicated airspeed, altitude, free-air temperature, and rudder position. The step-by-step flight procedure is described and information regarding evaluation of the control data and general suggestions is included.
- Progress Summary Number 1: Mechanical Properties of Flush-Riveted Joints Submitted by Five Airplane Manufacturers
- Summary presenting information on flush-riveted joints for aircraft construction, including the strength, occurrence of defects, and effect of the angle of rivet head. The current tests covers specimens from 15 manufacturers of which 5 series have been completed and are described in this report.
- Theoretical and Experimental Dynamic Loads for a Prismatic Float Having an Angle of Dead Rise of 22-1/2 Degrees
- Report discusses the maximum load, time to reach maximum load, and variation of load with time for prismatic floats in order to improve understanding of hydrodynamic theory for the landing impact of seaplane floats. Comparison of theoretical and experimental results and their applicability to flight impact are provided.
- Wind-Tunnel Tests of a Piston-Type Control Booster on an Airfoil and Aileron Model
- "Measurements of control moments were made in the NACA stability tunnel to determine the operational characteristics of a piston-type control booster on an aileron. The booster was so constructed and installed that pressures picked up from the air stream below the wing acted on a pair of pistons. The data are presented in the form of curves of pressure coefficients acting on the pistons, hinge-moment coefficients, and booster coefficients plotted against aileron deflection" (p. 1).
- An Approximate Determination of the Power Required to Move Control Surfaces as Related to Control-Booster Design
- "As a part of a general investigation of control boosters, preliminary calculations were made to indicate the sizes of control boosters necessary to move the controls of airplanes of various sizes. The analysis was based on the assumption that the controls were moved with a rapidity and amplitude equal to that measured with a fighter airplane in simulated combat. A corollary purpose consisted in determining the effect on reducing booster-power unit size of incorporating an energy accumulator in the booster system" (p. 1).
- Effect of Changes in Aileron Rigging on the Stick Forces of a High-Speed Fighter Airplane
- "The effects of changes in aileron rigging between 2 deg up and 2 deg down on the stick forces were determined from wind-tunnel data for a finite-span wing model. These effects were investigated for ailerons deflecting equally in both directions and linearly with stick deflection. Data were analyzed for a Frise, a sealed internally balanced, and a beveled-trailing-edge aileron" (p. 1).
- Aerodynamic Characteristics of Four NACA Airfoil Sections Designed for Helicopter Rotor Blades
- "The purpose of the present work is to extend the previous investigation and to derive additional airfoil sections designed to minimize the undesirable characteristics of the previously tested airfoils. The tests of these additional airfoils were made in the Langley two-dimensional low-turbulence tunnel (LTT)" (p. 2).
- Some Notes on the Determination of the Stick-Fixed Neutral Point From Wind-Tunnel Data
- "Two methods are presented for determining the horizontal location of the stick-fixed neutral point from wind-tunnel data. One method involves the solution of a mathematical equation; whereas the other method is a graphical solution for the same mathematical equation. The combined horizontal and vertical variation of the neutral point completely describes the stick-fixed longitudinal stability of airplanes that have large allowable center-of-gravity shifts" (p. 1).
- Comparison of Structural Efficiencies of Diagonal-Tension Webs and Truss Webs of 24S-T Aluminum Alloy
- "A comparison is made of the structural efficiencies of truss webs of 24S-T aluminum alloy with previously published values of the structural efficiencies of diagonal-tension webs of 24S-T aluminum alloy on the basis of identical allowable stresses. It is concluded that the diagonal-tension beam (web and flanges) can usually be built to be a more efficient beam than the truss beam, even though over a small range the web of a Warren truss beam is slightly more efficient than the web of a diagonal-tension beam" (p. 1).
- Effect of Variation in Diameter and Pitch of Rivets on Compressive Strength of Panels With Z-Section Stiffeners 1 - Panels With Close Stiffener Spacing That Fail by Local Buckling
- An experimental investigation is being conducted to determine the effect of varying the rivet diameter and pitch on the compressive strength of 24S-T aluminum-alloy panels with longitudinal Z-section stiffeners. The average stress at failing load for each rivet diameter, depth of countersink, and pitch of rivet is provided
- Tests of a Stressed-Carrying Door in Shear
- Bulletin presenting testing of a monocoque box with a stress-carrying door made and tested in torsion. The results indicate that if a stress-carrying door and its frame are made sufficiently heavy, the torsional stiffness of the box with the door can be made greater than the torsional stiffness of the box without the cut-out" (p. 1).
- Tests of a Stress-Carrying Door in Compression
- Bulletin presenting the results of bending tests on a monocoque box with the door on the compression side. The results indicate that the effectiveness of a stress-carrying door depends on the intended function of the door.
- A Comparison of Data Obtained by Two Flight Techniques for Determining the Sideslip Characteristics of a Fighter Airplane
- Report discusses data obtained from measuring sideslip characteristics via the continuous-record method and the steady-record method. The situations in which each recording method is preferred are presented.
- Test Data on the Shear Strength of Machine Countersunk-Riveted Joints Assembled by an NACA Flush-Riveting Procedure
- Bulletin presenting load-displacement curves for use in establishing allowable-load values for riveted joints assembled by an NACA flush-riveting procedure. Comparative data are also given to show the effect of variations in the procedure on the yield and maximum shear loads for the rivets.
- Shear Tests on DuPont Explosive Rivets With the Countersunk Head Milled Flush After Expansion
- Report discusses the results of shear testing in which the heads of Du Pont explosive countersunk rivets were allowed to protrude above the skin surface before expansion and the protruding portions were removed after expansion. As the height of the rivet head above the skin increases, the tightness of the rivet was found to increase. The report concludes that it may be desirable to investigating filling an entire shank with an explosive charge in order to permit greater tolerances in the drilled hole diameter and still have consistently tight rivets.
- Comparative Tests of the Strength and Tightness of Commercial Flush Rivets of One Type and NACA Flush Rivets in Machine-Countersunk and Counterpunched Joints
- Report discusses an investigation that was conducted to compare the strength and tightness of machine-countersunk flush-riveted joints assembled with NACA flush rivets and a type of commercial flush rivet. A comparison was also generated between the strength and tightness of counterpunched flush-riveted joints assembled with the same types of rivet. NACA's flush-riveted joints tended to be stronger and tighter than the commercial joints.
- A Study of the Tightness and Flushness of Machine-Countersunk Rivets for Aircraft
- Bulletin presenting the results of an investigation to determine possible improvements in the tightness and the flushness of machine-countersunk rivets. Specimens used in the study were simple lap joints made by different riveting methods. The results indicate that a comparison of the quality of machine-countersunk riveted joints on the basis of maximum load alone is not justified.
- Tests of Hydraulically Expanded Rivets
- Report discusses the results of an investigation into the tightness, shear strength, tensile strength, and life under pulsating loads of hollow, hydraulically expanded rivets made of 17S-T aluminum alloy. The countersunk-head rivets with inserts had a much higher maximum load in shear than the modified-roundhead rivets, which did not have inserts.
- Effect of Countersunk Depth on the Tightness of Two Types of Machine-Countersunk Rivet
- Bulletin presenting an investigation conducted to determine the effect of countersunk depth on the tightness of two types of machine-countersunk flush rivet. The specimens tested in the study were simple lap joints made by two different riveting methods. The results indicated that roundheaded rivets inserted from the back of the joint with the countersunk heads formed int he driving of the rivets produce tighter joints over a large range of depths than ordinary flush rivets.
- Proposal for a Propeller Side-Force Factor
- Report discusses a proposal for propeller manufacturers to consider the side-force factor with the activity factor as a fundamental parameter for all blade designs and for the side-force factor to be included in all reports of powered models in wind tunnels. The proposal includes a method for calculating the side-force factor and how it can be used in propeller development. It is shown to be a good index of the relative effectiveness per blade of a yawed propeller in developing side force.
- The belt method for measuring pressure distribution
- "The measurement of pressure distribution may be accomplished rapidly for any number of locations deemed necessary in model or full-scale investigations by use of the 'belt' method. Reasonable accuracy may be obtained by careful use of this method" (p. 1).
- End-zone water injection as a means of suppressing knock in a spark-ignition engine
- Report discusses the results of an investigation into the effectiveness of water injection into the combustion end zone of a spark-ignition engine cylinder for the suppression of knock. The injection angle was found to be very important for obtaining maximum results. The results of various angles and amounts of water were examined.
- Use of Internal Coolant as a Means of Permitting Increase in Engine Take-Off Power
- Engine tests, together with estimates made at Langley Memorial Aeronautical Laboratory, indicate that a 25-percent increase in take-off power can be obtained with present-day aircraft engines without increasing either the knock limit of the fuel or the external cooling requirements of the engine. This increase in power with present fuels and present external cooling is made possible through the use of an internal coolant inducted through the inlet manifold. Estimates on aircraft indicate that this 25-percent increase in power will permit an approximate usable increase of 8.5 percent in the take-off load of existing military airplanes. This increase in load is equivalent to an increase in the weight of gasoline normally carried of between 30 and 65 percent.
- Calculations of Intake-Air Cooling Resulting From Water Injection and of Water Recovery From Exhaust Gas
- Report discussing some calculations made for the effects of water in cooling the inlet air of aircraft-engine cylinders. From Summary: "The estimates indicate that the cooling effect of the water on the inlet air can be more extensive than the cooling now obtained with the intercoolers or aftercoolers in the air-induction system. In connection with water recovery from the exhaust gas, the estimates indicate that sufficient water can be recovered from 50 percent of the exhaust gas to provide an inducted water-fuel ratio of 0.5."
- Cylinder-Head Cooling by Means of a Shield in the Exhaust Passage
- "Tests were run on a single-cylinder, air-cooled engine with a Wright C9GC cylinder to determine the improvement in cylinder-head cooling that can be obtained by building into the exhaust passage an insulating shield designed to protect the valve-guide boss and the exhaust-passage walls from the exhaust gas. The test results showed an appreciable improvement in cooling of the exhaust-valve-guide boss, of the guide bushing, and of the valve seat" (p. 1).
- Test Data on the Shear Strength of Joints Assembled With Round-Head and Brazier-Head Rivets
- Report discusses data obtained from testing shear of joints riveted with round-head and brazier-head rivets. The tightness of the rivets is also compared for one value of rivet diameter. The load-displacement curves and comparison of load at various values of permanent displacement are presented for both types of rivets.
- A Positive-Replica Technique for Examining Finished Metal Surfaces and Its Application to Aircraft Engine Cylinders
- Report discusses a method of replica creation and testing of the surface-finish variation of aircraft engine parts subject to wear. In this report, a positive replica is created, the surface is treated, the replica is tested to make sure the fidelity is high enough, and a series of ring-sticking tests are conducted on the replicas. A summary of the results of the testing is also included.
- Method of Mounting Cylinder Blocks of in-Line Engines on CUE Crankcases
- Report describes the installation of six-cylinder blocks from two in-line aircraft engines on CUE crankcases, which permits the separate operation of any cylinder as part of a single-cylinder test engine. Using multicylinder-engine blocks for single-cylinder tests is advantageous because there is greater availability of standard engine parts and there is less temperature gradient. Modifications of the crankcase, camshaft-drive mechanism, and operation of the cylinder are described.
- Effect of Inlet-Air Temperature and Cylinder Displacement on Charge Temperature of Internal Combustion Engines
- Report discussing the effect of inlet-air temperature and cylinder displacement on the charge temperature of an internal-combustion engine at the end of the induction stroke. The experiment to test various types of cylinders and their results on the air temperature and pressure is described.
- Use of Water Injection to Decrease Gasoline Consumption in an Aircraft Engine Cruising at High Power
- Report discusses the results of testing water injection on a multicylinder aircraft engine and the potential fuel savings from the procedure. The speeds at which water injection for engine cooling is beneficial are illustrated and information about the manifold pressures and average rear spark-plug-gasket temperatures are also included.
- Comparative Fatigue Tests of Riveted Joints of Alclad 24S-T, Alclad 24S-T81, Alclad 24S-RT, Alclad 24S-T86 and Alclad 75S-T Sheet
- Report discusses testing performed to determine the fatigue strength of various types of riveted and spot-welded joints in the following aluminum alloys: Alclad 24S-T, 24S-RT, 758-T, 24S-T81, and 24S-T86. Details of the experiment, tensile properties, and information about failure are provided.
- An Investigation of the Characteristics of a Propeller Alcohol Feed Ring
- Report discusses the results of an investigation to compare the discharge characteristics of an alcohol feed ring and a standard alcohol discharge nozzle when utilized to supply anti-icing alcohol to the propeller-blade feed shoes on a Curtiss-Wright C-46 cargo airplane. The equipment used, testing practices, and results of the alcohol flow distribution are described.
- A Preliminary Study of Machine-Countersunk Flush Rivets Subjected to a Combined Static and Alternating Shear Load
- Report discusses the results of an investigation to study the effect of the height of a rivet head on the number of cycles required to cause failure of a machine-countersunk flush-riveted joint under a combined static and alternating shear load. A tight joint and a loose joint were tested and the number of cycles to failure and location of fatigue failure were compared.
- Critical Compressive Stress for Curved Sheet Supported Along All Edges and Elastically Restrained Against Rotation Along the Unloaded Edges
- "A formula is given for the critical compressive stress for slightly curved sheet with equal elastic restraints against rotation along the unloaded edges. The theory of small deflections is used and the formula reduces to that given by Timoshenko for the case of simply-supported edges. For larger curvatures, a modification of Redshaw's formula to include the effect of edge restraint is suggested" (p. 1).
- Some Strength Tests of Stiffened Curved Sheets Loaded in Shear
- Report discusses the results of strength tests of several curved-sheet 24S-T aluminum alloy specimens stiffened longitudinally and transversely and loaded in shear. Curved-web beams and cylindrical shells were both examined in the tests. Results provided include the load at which the sheet began to show shear buckles, where the buckles occurred, and whether or not the failures involved rupture of the sheet.
- Some Notes on the Determination of the Stick-Free Neutral Point from Wind-Tunnel Data
- "Two graphical methods are presented for determining the stick-free neutral point, and they are extensions of the methods commonly used to determine the stick-free neutral point. A mathematical formula for computing the stick-free neutral point is also given. These methods may be applied to determine approximately the increase in tail size necessary to shift the neutral point (stick fixed or free) to any desired location on an airplane having inadequate longitudinal stability" (p. 1).
- Influence of Loading Condition on Piloting Technique for Spin Recovery for Pursuit Airplanes
- Bulletin presenting a discussion of information as to the influence on spins and spin recovery of the wing loading and load distribution of present-day pursuit airplanes. The high wing loadings results in high rates of descent and large control forces for recovery.
- An analysis of the fatigue life of an airplane wing structure under overload conditions
- From Introduction: "Fatigue life expectancy in normal transport operations was investigated in reference 1 and was found to be of equal importance with single-gust life. The effect of overload operation of transport airplanes on the probability of encountering single critical gusts was investigated in reference 2 and the frequency of critical gusts was found to increase rapidly with overload. The effect of overload operation on fatigue strength, however, has not heretofore been evaluated, hence the investigations of references 1 and 2 are combined herein to permit such evaluation and to determine the relative importance of fatigue and single-gust failures under conditions of overload operation."
- An Approximate Method of Shear-Lag Analysis for Beams Loaded at Right Angles to the Plane of Symmetry of the Cross Section
- Report discussing strain measurements made on a box beam of triangular cross section and on two beams of D-section under transverse bending. Information about the arrangement of the beams and experimental and calculated stresses for different boxes.