UNT Libraries Government Documents Department - 1,423 Matching Results

Search Results

prev Results: 25 - 48 next
open access

Determination of the Characteristics of Tapered Wings

Description: This report presents tables and charts for use in determining the characteristics of tapered wings. Theoretical factors are given from which the following characteristics of tapered wings may be found: the span lift distribution, the induced-angle-of attack distribution, the lift-curve slope, the angle of zero lift, the induced drag, the aerodynamic-center position, and the pitching moment about the aerodynamic center.
Date: 1940
Creator: Anderson, Raymond F.
Item Type: Refine your search to only Report
open access

The experimental and calculated characteristics of 22 tapered wings

Description: From Summary: "The experimental and calculated aerodynamic characteristics of 22 tapered wings are compared, using tests made in the variable-density wind tunnel. The wings had aspect ratios from 6 to 12 and taper ratios from 1:6:1 and 5:1. The compared characteristics are the pitching moment, the aerodynamic-center position, the lift-curve slope, the maximum lift coefficient, and the curves of drag. The method of obtaining the calculated values is based on the use of wing theory and experiment… more
Date: November 17, 1937
Creator: Anderson, Raymond F.
Item Type: Refine your search to only Report
open access

Charts Relating the Compressive Buckling Stress of Longitudinally Supported Plates to the Effective Deflectional and Rotational Stiffness of the Supports

Description: "A stability analysis is made of a long flat rectangular plate subjected to a uniform longitudinal compressive stress and supported along its longitudinal edges and along one or more longitudinal lines by elastic line supports. The elastic supports possess deflectional and rotational stiffness. Such configuration is an idealization of the compression cover skin and internal structure of a wing and tail surfaces" (p. 1).
Date: 1954
Creator: Anderson, Roger A. & Semonian, Joseph W.
Item Type: Refine your search to only Report
open access

A flight evaluation of the longitudinal stability characteristics associated with the pitch-up of a swept-wing airplane in maneuvering flight at transonic speeds

Description: This report presents the results of flight measurements of longitudinal stability and control characteristics made on a swept-wing jet aircraft to determine the origin of the pitch-up encountered in maneuvering flight at transonic speeds. For this purpose measurements were made of elevator angle, tail angle of attack, and wing-fuselage pitching moments (obtained from measurements of the balancing tail loads).
Date: September 12, 1951
Creator: Anderson, Seth B. & Bray, Richard S.
Item Type: Refine your search to only Report
open access

Comparison of performance of experimental and conventional cage designs and materials for 75-millimeter-bore cylindrical roller bearings at high speed

Description: From Summary: "The results of two investigations, one to determine the relative merits of four experimental and two conventional design 75-millimeter-bore (size 215) cylindrical roller bearings and one to determine the relative merits of nodular iron and bronze as cage materials for this size and type of bearing, are presented in this report. Nine test bearings were operated over a range of dn values (product of bearing bore in mm and shaft speed in r.p.m) from 0.3 x 10(6) to 2.3 x 20(6), radia… more
Date: June 30, 1954
Creator: Anderson, William J.; Macks, E. Fred & Nemeth, Zolton N.
Item Type: Refine your search to only Report
open access

The development and application of high-critical-speed nose inlets

Description: From Summary: "An analysis of the nose-inlet shapes developed in previous investigations to represent the optimum from the standpoint of critical speed has shown that marked similarity exists between the nondimensional profiles of inlets which have widely different proportions and critical speeds. With the nondimensional similarity of such profiles established, the large differences in the critical speeds of these nose inlets must be a function of their proportions. An investigation was underta… more
Date: June 8, 1945
Creator: Baals, Donald D.; Smith, Norman F. & Wright, John B.
Item Type: Refine your search to only Report
open access

Preliminary experiments to determine scale and slip-stream effects on a 1/24th size model of a JN4H biplane

Description: This work was undertaken to obtain results on a small model of a complete airplane which might be used for comparison with corresponding tests made in full flight. Somewhat similar tests have been previously made at various other laboratories; but as certain discrepancies exist between corresponding tests in different tunnels, it has been deemed advisable to obtain a direct comparison for this particular installation. The present work covers tests on a one-twenty-fourth scale model at speeds va… more
Date: 1921
Creator: Bacon, D. L.
Item Type: Refine your search to only Report
open access

The resistance of spheres in wind tunnels and in air

Description: From Summary: "A satisfactory confirmation of Reynolds law has been accomplished, the effect of means of support determined, the range of experiment greatly extended by work in the new variable density wind tunnel, and the effects of turbulence investigated by work in the tunnels and by towing and dropping tests in free air. It is concluded that the erratic nature of most of the previous work is due to support interference and differing turbulence conditions. While the question of support has b… more
Date: 1924
Creator: Bacon, D. L. & Reid, E. G.
Item Type: Refine your search to only Report
open access

The Distribution of Lift Over Wing Tips and Ailerons

Description: "This investigation was carried out in the 5-foot wind tunnel of the Langley Memorial Aeronautical Laboratory for the purpose of obtaining more complete information on the distribution of lift between the ends of wing spars, the stresses in ailerons, and the general subject of airflow near the tip of a wing. It includes one series of tests on four models without ailerons, having square, elliptical, and raked tips respectively, and a second series of positively and negatively raked wings with ai… more
Date: 1924
Creator: Bacon, David L.
Item Type: Refine your search to only Report
open access

A simplified theoretical method of determining the characteristics of a lifting rotor in forward flight

Description: Theoretical derived expressions for the flapping, the thrust, the torque, and the profile drag-lift ratio of nonfeathering rotor with hinged, rectangular, linearly twisted blades are given as simple functions of the inflow velocity and the blade pitch. Representative values of the coefficients of each of the terms in these expressions are tabulated for a series of specified values of the tip-speed ratio. Analysis indicates that the tabulated values can be used to calculate, with reasonable accu… more
Date: March 17, 1941
Creator: Bailey, F. J., Jr.
Item Type: Refine your search to only Report
open access

A study of the torque equilibrium of an autogiro rotor

Description: From Summary: "Two improvements have been made in the method developed in NACA Reports nos. 487 and 591 for the estimation of the inflow velocity required to overcome a given decelerating torque in an autogiro rotor. At low tip-speed ratios, where the assumptions necessary for the analytical integrations of the earlier papers are valid, the expressions therein derived are greatly simplified by combining and eliminating terms with a view of minimizing the numerical computations required. At high… more
Date: January 10, 1938
Creator: Bailey, F. J., Jr.
Item Type: Refine your search to only Report
open access

Spinning characteristics of the XN2Y-1 airplane obtained from the spinning balance and compared with results from the spinning tunnel and from flight tests

Description: Report presents the results of tests of a 1/10-scale model of the XN2Y-1 airplane tested in the NACA 5-foot vertical wind tunnel in which the six components of forces and moments were measured. The model was tested in 17 attitudes in which the full-scale airplane had been observed to spin, in order to determine the effects of scale, tunnel, and interference. In addition, a series of tests was made to cover the range of angles of attack, angles of sideslip, rates of rotation, and control setting… more
Date: April 16, 1937
Creator: Bamber, M. J. & House, R. O.
Item Type: Refine your search to only Report
open access

The Aerodynamic Forces and Moments Exerted on a Spinning Model of the NY-1 Airplane as Measured by the Spinning Balance

Description: From Summary: "A preliminary investigation of the effects of changes in the elevator and rudder settings and of small changes in attitude upon the aerodynamic forces and moments exerted upon a spinning airplane was undertaken with the spinning balance in the 5-foot vertical tunnel of the National Advisory Committee for Aeronautics. The tests were made on a 1/12-scale model of the "NY-1" airplane. Data by which to fix the attitude, the radius of spin, and the rotational and air velocities were t… more
Date: February 7, 1933
Creator: Bamber, M. J. & Zimmerman, C. H.
Item Type: Refine your search to only Report
open access

Spinning characteristics of wings 1: rectangular Clark Y monoplane wing

Description: "A series of wind tunnel tests of a rectangular Clark Y wing was made with the NACA spinning balance as part of a general program of research on airplane spinning. All six components of the aerodynamic force and moment were measured throughout the range of angles of attack, angles of sideslip, and values omega b/2v likely to be attained by a spinning airplane; the results were reduced to coefficient form. It is concluded that a conventional monoplane with a rectangular Clark y wing can be made … more
Date: November 21, 1934
Creator: Bamber, M. J. & Zimmerman, C. H.
Item Type: Refine your search to only Report
open access

Wind-Tunnel Tests on Airfoil Boundary Layer Control Using a Backward-Opening Slot (1931)

Description: "This report presents the results of an investigation to determine the effect of boundary layer control on the lift and drag of an airfoil. Boundary layer control was accomplished by means of a backward-opening slot in the upper surface of the hollow airfoil. Air was caused to flow through this slot by a pressure which was maintained inside the airfoil by a blower. Various slot locations, slot openings, and wing pressures were used" (p. 3).
Date: 1931
Creator: Bamber, Millard J.
Item Type: Refine your search to only Report
open access

Flight Investigation at High Speeds of the Drag of Three Airfoils and a Circular Cylinder Representing Full-Scale Propeller Shanks

Description: "Tests have been made at high speeds to determine the drag of models, simulating propeller shanks, in the form of a circular cylinder and three airfoils, the NACA 16-025, the NACA 16-040, and the NACA 16-040 with the rear 25 percent chord cut off. All the models had a maximum thickness of 4 1/2 inches to conform with average propeller-shank dimensions and a span of 20 1/4 inches. For the tests the models were supported perpendicular to the lower surface of the wing of an XP-51 airplane (p. 277). more
Date: June 7, 1946
Creator: Barlow, William H.
Item Type: Refine your search to only Report
open access

Study of effects of sweep on the flutter of cantilever wings

Description: An experimental and analytical investigation of the flutter of sweptback cantilever wings is reported. The experiments employed groups of wings swept back by rotating and by shearing. The angle of sweep range from 0 degree to 60 degrees and Mach numbers extended to approximately 0.85. A theoretical analysis of the air forces on an oscillating swept wing of high length-chord ratio is developed, and the approximations inherent in the assumptions are discussed. Comparison with experiment indicates… more
Date: September 9, 1948
Creator: Barmby, J. G.; Cunningham, H. J. & Garrick, I. E.
Item Type: Refine your search to only Report
open access

Estimation of F-3 and F-4 knock-limited performance ratings for ternary and quaternary blends containing triptane or other high-antiknock aviation-fuel blending agents

Description: Charts are presented that permit the estimation of F-3 and F-4 knock-limited performance ratings for certain ternary and quaternary fuel blends. Ratings for various ternary and quaternary blends estimated from these charts compare favorably with experimental F-3 and F-4 ratings. Because of the unusual behavior of some of the aromatic blends in the F-3 engine, the charts for aromatic-paraffinic blends are probably less accurate than the charts for purely paraffinic blends.
Date: January 20, 1945
Creator: Barnett, Henry C.
Item Type: Refine your search to only Report
open access

NACA investigation of fuel performance in piston-type engines

Description: This report is a compilation of many of the pertinent research data acquired by the National Advisory Committee for Aeronautics on fuel performance in piston engines. The original data for this compilation are contained in many separate NACA reports which have in the present report been assembled in logical chapters that summarize the main conclusions of the various investigations. Complete details of each investigation are not included in this summary; however, such details may be found, in th… more
Date: May 15, 1951
Creator: Barnett, Henry C.
Item Type: Refine your search to only Report
open access

Basic considerations in the combustion of hydrocarbon fuels with air

Description: Basic combustion research is collected, collated, and interpreted as it applies to flight propulsion. The following fundamental processes are treated in separate chapters: atomization and evaporation of liquid fuels, flow and mixing processes in combustion chambers, ignition and flammability of hydrocarbon fuels, laminar flame propagation, turbulent flames, flame stabilization, diffusion flames, oscillations in combustors, and smoke and coke formation in the combustion of hydrocarbon-air mixtur… more
Date: 1957
Creator: Barnett, Henry C. & Hibbard, Robert R.
Item Type: Refine your search to only Report
open access

A Simplified Method of Elastic-Stability Analysis for Thin Cylindrical Shells

Description: "This paper develops a new method for determining the buckling stresses of cylindrical shells under various loading conditions. In part I, the equation for the equilibrium of cylindrical shells introduced by Donnell in NACA report no. 479 to find the critical stresses of cylinders in torsion is applied to find critical stresses for cylinders with simply supported edges under other loading conditions. In part II, a modified form of Donnell's equation for the equilibrium of thin cylindrical shell… more
Date: March 20, 1947
Creator: Batdorf, S. B.
Item Type: Refine your search to only Report
open access

Critical combinations of shear and transverse direct stress for an infinitely long flat plate with edges elastically restrained against rotation

Description: An exact solution and a closely concurring approximate energy solution are given for the buckling of an infinitely long flat plate under combined shear and transverse direct stress with edges elastically restrained against rotation. It was found that an appreciable fraction of the critical stress in pure shear may be applied to the plate without any reduction in the transverse compressive stress necessary to produce buckling. An interaction formula in general use was shown to be decidedly conse… more
Date: November 8, 1944
Creator: Batdorf, S. B. & Houbolt, John C.
Item Type: Refine your search to only Report
open access

Critical Stress of Thin-Walled Cylinders in Axial Compression

Description: Empirical design curves are presented for the critical stress of thin-wall cylinders loaded in axial compression. These curves are plotted in terms of the nondimensional parameters of small-deflection theory and are compared with theoretical curves derived for the buckling of cylinders with simply supported and clamped edges. An empirical equation is given for the buckling of cylinders having a length-radius ratio greater than about 0.75.
Date: March 20, 1947
Creator: Batdorf, S. B.; Schildcrout, Murry & Stein, Manuel
Item Type: Refine your search to only Report
open access

The Decay of a Simple Eddy

Description: The principal result obtained in this report is a generalization of Taylor's formula for a simple eddy. The discussion of the properties of the eddy indicates that there is a slight analogy between the theory of eddies in a viscous fluid and the quantum theory of radiation. Another exact solution of the equations of motion of viscous fluid yields a result which reminds one of the well-known condition for instability in the case of a horizontally stratified atmosphere.
Date: 1923
Creator: Bateman, H.
Item Type: Refine your search to only Report
Back to Top of Screen