Report presenting an application of the principle of aileron-stick forces and mechanical advantage to an aileron installation in which the stick forces are small over the low-deflection range and excessively large at full deflection.
"The purpose of the present work is to extend the previous investigation and to derive additional airfoil sections designed to minimize the undesirable characteristics of the previously tested airfoils. The tests of these additional airfoils were made in the Langley two-dimensional low-turbulence tunnel (LTT)" (p. 2).
From Introduction: "Fatigue life expectancy in normal transport operations was investigated in reference 1 and was found to be of equal importance with single-gust life. The effect of overload operation of transport airplanes on the probability of encountering single critical gusts was investigated in reference 2 and the frequency of critical gusts was found to increase rapidly with overload. The effect of overload operation on fatigue strength, however, has not heretofore been evaluated, hence the investigations of references 1 and 2 are combined herein to permit such evaluation and to determine the relative importance of fatigue and single-gust failures under conditions of overload operation."
Analysis was made to determine characteristics required of a balancing-tab system for ailerons in order to reduce aileron stick forces to any desired magnitude. Series of calculations based on section data were made to determine balancing-tab systems of various chord tabs and ailerons that will give, for a particular airplane, zero rate of aileron hinge moment with aileron deflection and yet will produce same maximum rate of roll as a plain unbalanced 15-percent chord aileron of same span. Effects of rolling velocity and of forces in tab link on aileron hinge moments have been included.
"As a part of a general investigation of control boosters, preliminary calculations were made to indicate the sizes of control boosters necessary to move the controls of airplanes of various sizes. The analysis was based on the assumption that the controls were moved with a rapidity and amplitude equal to that measured with a fighter airplane in simulated combat. A corollary purpose consisted in determining the effect on reducing booster-power unit size of incorporating an energy accumulator in the booster system" (p. 1).
Report discussing strain measurements made on a box beam of triangular cross section and on two beams of D-section under transverse bending. Information about the arrangement of the beams and experimental and calculated stresses for different boxes.
Report discusses an analysis and preliminary design of a control linkage that varies automatically with dynamic pressure. The advantages of the device, including greater lateral control than a fixed control linkage without additional aerodynamic balance, are detailed. The effect of variable linkage on lateral-control characteristics is also described.
"The measurement of pressure distribution may be accomplished rapidly for any number of locations deemed necessary in model or full-scale investigations by use of the 'belt' method. Reasonable accuracy may be obtained by careful use of this method" (p. 1).
"Formulas for the calculation of hinge-moment characteristics of an elevator with a spring tab have been developed in terms of basic aerodynamic parameters, spring stiffness, and airspeed. The formulas have been used in a study of the stick-force gradients on a pursuit airplane equipped with an elevator with a spring tab. Charts are presented showing the variation of stick-force gradient in accelerated flight over a large range of speed and the complete range of spring stiffness for various center-of-gravity locations, altitudes, and airplane sizes" (p. 1).
Report presenting tail-surface characteristics calculated from wind-tunnel data, which have been reported to not correspond with flight-test measurements. The primary problem under consideration is the calculation of the effect of tab deflection on the free-floating angle of the elevator, as in a servocontrol.
Report discussing some calculations made for the effects of water in cooling the inlet air of aircraft-engine cylinders. From Summary: "The estimates indicate that the cooling effect of the water on the inlet air can be more extensive than the cooling now obtained with the intercoolers or aftercoolers in the air-induction system. In connection with water recovery from the exhaust gas, the estimates indicate that sufficient water can be recovered from 50 percent of the exhaust gas to provide an inducted water-fuel ratio of 0.5."
Report discusses testing performed to determine the fatigue strength of various types of riveted and spot-welded joints in the following aluminum alloys: Alclad 24S-T, 24S-RT, 758-T, 24S-T81, and 24S-T86. Details of the experiment, tensile properties, and information about failure are provided.
Report discusses an investigation that was conducted to compare the strength and tightness of machine-countersunk flush-riveted joints assembled with NACA flush rivets and a type of commercial flush rivet. A comparison was also generated between the strength and tightness of counterpunched flush-riveted joints assembled with the same types of rivet. NACA's flush-riveted joints tended to be stronger and tighter than the commercial joints.
Report discusses data obtained from measuring sideslip characteristics via the continuous-record method and the steady-record method. The situations in which each recording method is preferred are presented.
"A comparison is made of the structural efficiencies of truss webs of 24S-T aluminum alloy with previously published values of the structural efficiencies of diagonal-tension webs of 24S-T aluminum alloy on the basis of identical allowable stresses. It is concluded that the diagonal-tension beam (web and flanges) can usually be built to be a more efficient beam than the truss beam, even though over a small range the web of a Warren truss beam is slightly more efficient than the web of a diagonal-tension beam" (p. 1).
Report presenting an investigation to determine whether the use of a 78 degree countersinking tool instead of a 82 degree countersinking tool for riveting would substantially alter the conclusion reached in a previous paper regarding the placement of rivets for maximum strength.
Report discusses the differences between the mean tangential velocity of the air leaving the blade tips of a centrifugal supercharger calculated by the conventional turbine equation and by an equation that uses the isentropic increase in total enthalpy. The velocities are compared to experimental values observed with three diffusers.
"A formula is given for the critical compressive stress for slightly curved sheet with equal elastic restraints against rotation along the unloaded edges. The theory of small deflections is used and the formula reduces to that given by Timoshenko for the case of simply-supported edges. For larger curvatures, a modification of Redshaw's formula to include the effect of edge restraint is suggested" (p. 1).
"Tests were run on a single-cylinder, air-cooled engine with a Wright C9GC cylinder to determine the improvement in cylinder-head cooling that can be obtained by building into the exhaust passage an insulating shield designed to protect the valve-guide boss and the exhaust-passage walls from the exhaust gas. The test results showed an appreciable improvement in cooling of the exhaust-valve-guide boss, of the guide bushing, and of the valve seat" (p. 1).
Bulletin presenting an examination of a part of the anti-icing equipment for a Ju 88 airplane, including exhaust-air heat exchangers, control valves, air duct system, and air-heated wing panels. Testing was performed on the components and indicated that the thermal ice-prevention equipment can maintain the outer-wing panel free from ice.
"Typical thrust and torque coefficients and increments, due to the propeller, in the ratio of the dynamic pressure at the tail to the free-stream dynamic pressure are presented for 10 full-scale airplanes. Calculations indicate that an error of about 2 percent mean aerodynamic chord appears possible in determining the neutral point from wind-tunnel tests or a model in the gliding condition if the propeller is operated at zero thrust rather than at the values of thrust coefficient indicated by the flight tests" (p. 1).
From Summary: "Local-instability tests of 24S-T aluminum-alloy formed Z- and channel-section columns were made in order to determine a length of test specimen that would avoid the increased strength associated with short lengths and also permit the occurrence of a convenient buckling pattern. The effect of column length on the critical compressive stress, on the average stress at maximum load, and on the number of half-waves of the buckling pattern is shown."
Report discusses methods of determining the iron contamination of used lubricating oil in order to study wear rates of piston rings and cylinder barrels of aircraft engines. Two methods of separating iron from used lubricating oil are presented. The results of the analyses of the oil are presented and the methods are evaluated.
Report discusses the results of an investigation to determine the effect of a collector ring on exhaust-gas sampling. The results of tests to determine the percentage by volume of exhaust gas from the collector ring are presented for several engine powers and speeds. The danger of air dilution from the breathing action of the engine is almost entirely eliminated by the use of a collector ring.
Report discusses an apparatus that may be used for indicating the formation of fatigue cracks or for following the progress of cracks. Details of the experiment and discussion of the way in which the deflection-crack area relationship may be used to monitor fatigue cracks are included.
"Thirty-nine Z-sections formed from 24S-T aluminum-alloy sheet with the angle of bend between the flanges and the web varying from 5 degrees to 120 degrees were tested as columns. Angles of bend from 30 degrees to 120 degrees had little or no effect on the critical stress or on the average stress at maximum load for local instability of the columns. The lengths of the columns were such that at angles of bend below 30 degrees they failed by Euler buckling" (p. 1).
"An experimental study was made to determine the effect of artificial aging on the tensile properties of alclad 24S-T and 24S-T aluminum-alloy sheet material. The results of the tests show that certain combinations of aging time and temperature cause a marked increase in the yield strength and a small increase in the ultimate strength; these increases are accompanied by a very large decrease in elongation. A curve is presented that shows the maximum yield strengths that can be obtained by aging this material at various combinations of time and temperature" (p. 1).
"The effects of changes in aileron rigging between 2 deg up and 2 deg down on the stick forces were determined from wind-tunnel data for a finite-span wing model. These effects were investigated for ailerons deflecting equally in both directions and linearly with stick deflection. Data were analyzed for a Frise, a sealed internally balanced, and a beveled-trailing-edge aileron" (p. 1).
Bulletin presenting an investigation conducted to determine the effect of countersunk depth on the tightness of two types of machine-countersunk flush rivet. The specimens tested in the study were simple lap joints made by two different riveting methods. The results indicated that roundheaded rivets inserted from the back of the joint with the countersunk heads formed int he driving of the rivets produce tighter joints over a large range of depths than ordinary flush rivets.
Report discussing the effect of inlet-air temperature and cylinder displacement on the charge temperature of an internal-combustion engine at the end of the induction stroke. The experiment to test various types of cylinders and their results on the air temperature and pressure is described.
Report discusses the results of testing of rudder deflection for trim at low speeds in the critical wave-off condition. Depending on the lateral center-of-gravity location on the airplane, the useful load in the wings will change and the ability of the rudder to trim the airplane may be greatly improved.
Results are presented of tests of two specimens tested to study the effect of normal pressure on the critical compressive stress for thin curved sheets. These specimens are designated by their respective rib spacings of 10 inches and 30 inches. The relationship between compressive stress and normal pressure at which buckles disappeared is independent of whether the buckles were made to disappear by increase of normal pressure or decrease of compressive stress. (author).
"In order to determine the critical stresses caused by an outward acting pressure on the upper surface of a wing due to the difference in internal and external pressures, torsional tests were made on two curved-sheet specimens subjected to an outward acting normal pressure. Results show that an outward acting normal pressure appreciable raises the critical shear stress for an unstiffened curved sheet; the absolute increase in critical shear stress is slightly greater for a 30 in. rib spacing than for a 10 in. rib spacing" (p. 1).
Report discusses the "effects of oil introduced into the combustion chamber and of oil-spray piston cooling on the knock-limited performance of aircraft engines" (from Summary). A CFR engine and Allison V-1710 cylinder were used to test the rate of oil consumption, knock, and knock-limited brake mean effective pressure.
Report discusses the results of two tests: "1) aerodynamic tests to determine the effect of the slipstream and thrust from the powered propellers on the lift and trimming-moment characteristics, and 2) hydrodynamic tests to determine the effect of the powered propellers on the range of stable locations of the center of gravity (from Introduction)." Large differences in the stable range between half-thrust and full-thrust conditions were observed. Three effects of power were also involved in the location of the stable range of the center of gravity.
An experimental investigation is being conducted to determine the effect of varying the rivet diameter and pitch on the compressive strength of 24S-T aluminum-alloy panels with longitudinal Z-section stiffeners. The average stress at failing load for each rivet diameter, depth of countersink, and pitch of rivet is provided
"These tests were run to determine the effect that mixing engine exhaust gas with engine intake air has on fuel knock limit, specific fuel consumption, and air consumption." Information about the effect on pressure, air consumption, and fuel consumption is detailed.
Report discusses the effects of compressibility and angle of yaw on the pressure measured by a round-nose and a flat-nose total-pressure tube. The error incurred in the pressure measurements and factors affecting the total-pressure area are described.
Report discussing the results of testing to discover the effects of fuel-vapor loss on F-3 and F-4 knock-limited performance ratings and inspection properties of two aviation fuels, 28-R and 33-R. The percentage of loss at several temperatures, ability to meet Army-Navy fuel specifications, and antiknock rating change is described.
"An electronic circuit for instantaneously indicating angular velocity and acceleration, both positive and negative, of rotating masses is described; readings are taken on electrical indicating meters. The indicator is described in terms of general application. A circuit diagram, calibration curves, and a mathematical analysis of the differentiation circuit are included" (p. 1).
"An analysis was made to show the relative effectiveness of streamline external fuel tanks, a fuel tank in the form of a wing mounted in a biplane position, and auxiliary wing panels attached at the wing tips to increase the span as temporary means for increasing the range of a fighter-type airplane. Figures and charts for the various devices considered show the results of calculations of range, duration of flight, and take-off distance for both land-base and carrier operation. The results indicated that the wing-tip extensions were the most promising of the devices considered" (p. 1).
Report discusses the results of an investigation into the effectiveness of water injection into the combustion end zone of a spark-ignition engine cylinder for the suppression of knock. The injection angle was found to be very important for obtaining maximum results. The results of various angles and amounts of water were examined.
Report discusses a method developed to estimate the quantities of internal coolants required to prevent overheating of the aircraft cylinder when oxygen boost is applied. The formula and calculations related to inlet-air pressure, added oxygen, added water, added nitrogen, and total fluid weight are detailed.
Report presenting an exploration of fatigue stresses of some wrought aluminum alloys, including charts that cover different ranges of stress and number of cycles.
Report discusses an investigation into static pressures in subsonic and supersonic flow over an airplane wing as measured by static-pressure tubes, a static-pressure belt, and orifices flush with the wing surface. The results obtained from the three types of measuring devices and a comparison to theoretical calculations are presented.
Report presenting an investigation to determine whether some characteristic of the boundary layer could be used to provide warning of the increase in stalling speed of a wing caused by ice formations on the leading edge. Results were analyzed by referring the total pressures at the rake to the free-stream total pressure, static pressure at the rake, free-stream static pressure, and static pressure from wind-tip swiveling head.
"The stability characteristics of a glider towed by twin parallel towlines have been studied in the NACA free-flight tunnel. A preliminary theoretical analysis of the stability of a glider restrained from yawing was followed by an experimental investigation of the stability of a model towed from fixed tunnel points in such a way as to simulate tow in level flight. The results of the tests confirm the theoretical analysis and indicate that a pilotless, stable, towed-glider system is possible when twin parallel towcables are used" (p. 1).
Report discusses the results of an investigation to determine the feasibility of using the change in the specific gravity of fuels in aircraft fuel tanks to measure fuel-vaporization loss. Six fuels were tested via fuel-distillation tests and simulated-flight tests. An equation based on the specific gravity of the fuel is also described.
Report discusses measurements of the relaxation time of steam and nitrogen due to their importance as turbine-working fluids. Additional calculations regarding different nozzle lengths are included.
Report presenting stability testing of two dynamic models in tank no. 1 in order to investigate the effects of adding a small projection, or hook, on the planing bottom of the forebody near the step of a seaplane. Tests with two different projections had a rather large effect on all of the trim limits and the landing stability.
This dialog allows you to filter your current search.
Each of the Serial/Series Titles listed note their name and the number of records that will be limited down to if you choose that option.
This dialog allows you to filter your current search.
Each of the Years listed note their name and the number of records that will be limited down to if you choose that option.
This dialog allows you to filter your current search.
Each of the Months listed note their name and the number of records that will be limited down to if you choose that option.
The list can be sorted by name or the count.
This dialog allows you to filter your current search.
Each of the Days listed note their name and the number of records that will be limited down to if you choose that option.