The report contains a description of the DVL wind tunnel. According to the cones fixed, an elliptical stream with axes 5 by 7 meters and length 9 meters, or a stream 6 by 8 meters in cross section and 11 meters in length is available. The top speed with the smaller cone is 65 meters per second. The testing equipment consists of an automatic six-component balance and a test rig for propellers and engines up to 650 horsepower.
Report discussing the 6-foot-4-inch wind tunnel and its auxiliary equipment has proven itself capable of continuous and reliable output of data. The real value of the tunnel will increase as experience is gained in checking the observed tunnel performance against full-scale performance. Such has been the case of the 8- by 8-foot tunnel, and for that reason the comparison in the calibration tests have been presented.
This report presents a description of the 7 by 10 foot wind tunnel and associated apparatus of the National Advisory Committee for Aeronautics. Included also are calibration test results and characteristic test data of both static force tests and autorotation tests made in the tunnel.
From Introduction: "This paper, which should be of interest to those concerned with transonic wind tunnels, covers the design and operating characteristics of the nozzle."
This report provides a description of the Benz 300 H.P. aircraft engine containing 12 cylinders placed at a 60° angle. It includes a detailed description of the development of the constructional points, particularly the cylinders, pistons, and connecting rods, as well as the engine fitting, lubrication, oil pumps, bearings, oil tank, fuel pump, carburetors, and cooling system. There are seven pages of illustrative figures at the end of the report.
Report details the characteristics and advantages of the swift traffic airplane constructed by Zeppelin Works at Staaken. The maximum speed, weight, construction, layout, and landing capabilities of the plane are included.
From Summary: "These properties compare favorably with those of the strongest similar alloys previously investigated. However, compared with a 60Cr-25Fe-15Mo alloy, the three cobalt-chronium-nickel cast alloys are inferior. A correlation of NACA and OSRD (Project NRC-8) data is presented, showing the variation of rupture strengths with temperature in the range of 1350^o to 2000^o for alloys."
The report discusses the problem of rating the various seaplane designs from the 1926 seaplane contest. The whole process of rating consists in measuring the climbing speed, flying weight and carrying capacity of a seaplane and then using these data as the basis of a construction problem.
The limitation of the 1929 contest to performance gliders necessitated the establishment of a formula which would make it possible to distinguish between performance gliders and school and training gliders. The sinking speed was therefore adopted as the basis for such a distinction, and the requirement was made that the sinking speed of a performance glider should not exceed 0.8 m/s. The rest of the report details the different entries with regard to design and performance.
Report discussing the A.B.C. Motors Robin, a single-seat monoplane that was built for pilot comfort, speed, and fuel efficiency. Information about the structural design, dimensions, weight, performance, and rough blueprints is included.
Report discusses the characteristics of the K 37 all-metal long-wing monoplane and its use for long-distance scouting, as a day bomber, and as a heavy fighting airplane. Its engines, climbing capacity, action radius, bombing installation, fuselage, controls, and landing gear are explored in depth.
Report discussing a new instrument is described which is capable of simultaneously recording the position of the three controls of an airplane. The records are taken photographically on a standard N.A.C.A. film drum and the instrument can be quickly installed in any airplane.
"A new trailing bomb-type instrument for photographically recording the flight-path angle and air speed of aircraft in unaccelerated flight is described. The instrument consists essentially of an inclinometer, air-speed meter and a film-drum case. The inclinometer carries an oil-damped pendulum which records optically the flight-path angle upon a rotating motor-driven film drum. The air-speed meter consists of a taut metal diaphragm of high natural frequency which is acted upon by the pressure difference of a Prandtl type Pitot-static tube" (p. 1).
A description is given of a tilting manometer designed to meet the requirements of a manometer for use in the wind tunnel at the Langley Memorial Aeronautical Laboratory. This gauge was designed to meet the requirements of a manometer in use in connection with a static pressure plate to indicate the wind speed in the tunnel. The requirements are noted. The sensitivity of the gauge must be made inversely proportional to the pressure to be measured. The gauge must be accurately and quickly set for any desired pressure.
A new type of air speed meter is described which was designed by the technical staff of the National Advisory Committee for Aeronautics. The instrument consists essentially of a tight metal diaphragm of high natural period which is acted upon by the pressure difference of a pitot-static head. The resulting deflection of this diaphragm is recorded optically on a moving film.
With some airplanes the approach to the stall is accompanied by changes in the behavior, such as tail buffeting or changes in the control characteristics of the airplane so that the pilot obtains a warning of the impending stall. Vith other airplanes it is possible to approach the stall without any perceptible warning other than the reading of the air-speed meter, in which case the danger of inadvertent stalling is considerably greater. Although it is not within the scope of this paper to discuss stalling characteristics, it is desired to point out that in general the danger of inadvertent stalling is greatest with those airplanes that behave worse when the stalling occurs; that is, with airplanes in which the stall starts at the wing tips. A warning of the impending stall is desirable in any case, but is particularly desirable with airplanes of the latter type.
"The stall-warning indicator employs a total-head tube located close to the wing surface in a region wherein local stalling occurs before the main portion of the wing stalls. The artificial production of a localized stalled region is accomplished by means of a sharp leading edge extending a few inches along the span. An abrupt drop in the total pressure relative to a static reference taken at some convenient point occurs at the stall in this region" (p. 1).
A product of the Air Navigation Engineering Co., the Missel Thrush is a light airplane suitable for private ownership. It is a two seat tractor fuselage biplane with single I interplane struts designed by J. Bewsher.
This report presents a description of an abacus with three scales: one for English measures, one for metric measures, and one with the "points of reduction", as well as construction details. There is also a detailed description on how to use the abacus.
Comparing the results of the calculations for computing the mean pressure of an aviation engine for any number of revolutions, with those of experiment, the writer, by numerous examples, shows the perfect agreement between them. This report will show that, by means of a special abacus, an engineer can instantly plot the characteristics of an engine.
Report discussing an investigation into the ability of human pilots to control short-period yawing oscillations using a yaw simulating device. The ability to control the oscillations was determined to be a function of period, control effectiveness, and inherent damping. Pilot control effectiveness was found to improve with practice.
Report discussing an experimental investigation was carried out on air- and vacuum-melted M-252 and S-816 alloys to find conditions of heating and hot-working which resulted in abnormal grain growth. The experiments were mainly limited to normal conditions of heating for hot-working and heat treatment and normal temperatures of solution treatment were used to allow grain growth after susceptibility to abnormal grain growth was developed by various experimental conditions. Results indicated that small reductions of essentially strain-free metal were the basic cause of such grain growth.
From Introduction: "The data included in this report for Nimonic 80A alloy, for instance, represent experiments carried out to help clarify a production problem of grain-size control in an alloy which has been extensively used. The general procedure of the investigation was to carry out controlled laboratory experiments on samples of bar stock to find conditions of heating and hot-working which resulted in abnormal grain growth."
From Introduction: "This report presents the results obtained to date of an investigation to establish the fundamental causes of abnormal growth in S-816 alloy under conditions encountered during the forging of blades for the gas turbine of jet engines."
It is argued that there should be an agreement as to what conventions to use in determining absolute coefficients used in aeronautics and in how to plot those coefficients. Of particular importance are the absolute coefficients of lift and drag. The author argues for the use of the German method over the kind in common use in the United States and England, and for the Continental over the usual American and British method of graphically representing the characteristics of an airfoil.
Note presenting an investigation of the Karman vortex street, which is a flow arrangement occurring behind a plate. The equations governing the flow and some of the hypotheses behind it are provided.
Report discussing about 400 references pertaining to the hydrodynamic design of seaplanes have been compiled, and the information is presented in the form of abstracts classified under six main headings.
Report presenting a study of the acceleration characteristics of a turbojet engine equipped with variable-position inlet guide vanes in the altitude test chamber. Maximum acceleration values for 3 engines of the same model were also obtained during testing and were found to differ as much as 50 percent. Results regarding the effect of fuel step size and inlet guide vane on acceleration, effect of flight condition, reproducibility of engine acceleration, compressor pressure ratio in relation to acceleration, and acceleration with inlet air distortion are provided.
From Summary: "Qualitative investigations have shown that use of the NACA injection impeller with the R-3350 engine increases the inertia of the fuel-injection system and, when the standard fuel-metering system is used, this increase in inertia results in poor engine acceleration characteristics. This investigation was therefore undertaken to determine whether satisfactory acceleration characteristics of the engine equipped with the injection impeller could be obtained by simple modifications to the fuel-monitoring system. The engine was operated with two types of carburetor; namely, a hydraulic-metering carburetor incorporating a vacuum-operated accelerating pump and a direct-metering carburetor having a throttle-actuated accelerating pump."
From Summary: "Tests of a 1/7 size model of the Grumman XJR2F-1 amphibian were made in Langley tank no.1 to examine the landing behavior in rough water and to measure the normal and angular accelerations experienced by the model during these landings. All landings were made normal to the direction of wave advance, a condition assumed to produce the greatest accelerations. Wave heights of 4.4 and 8.0 inches (2.5 and 4.7 ft, full size) were used in the tests and the wave lengths were varied between 10 and 50 feet (70 and 350 ft, full size)."
A 1/5.5-size powered dynamic model of the Columbia XJL-1 amphibian was landed in Langley tank no. 1 in smooth water and in oncoming waves of heights from 2.1 feet to 6.4 feet (full-size) and lengths from 50 feet to 264 feet (full-size). The motions and the vertical accelerations of the model were continuously recorded. The greatest vertical acceleration measured during the smooth-water landings was 3.1g.
From Summary: "An analytical investigation was made to determine from component performance characteristics the effect of air bleed at the compressor outlet on the acceleration characteristics of a typical high-pressure-ratio single-spool turbojet engine. Consideration of several operating lines on the compressor performance map with two turbine-inlet temperatures showed that for a minimum acceleration time the turbine-inlet temperature should be the maximum allowable, and the operating line on the compressor map should be as close to the surge region as possible throughout the speed range. Operation along such a line would require a continuously varying bleed area."
Report presenting an analytical investigation to determine the effect of compressor interstage air bleed with the use of constant-area bleed ports on the acceleration characteristics of a typical high-pressure-ratio single-spool turbojet engine. Constant-area interstage bleed, properly located, gave smaller acceleration times than variable-area compressor exit bleed. Results regarding acceleration with interstage bleed, acceleration using constant-area interstage bleed in combination with compressor outlet bleed, variable-area interstage bleed, and comparison of acceleration modes are provided.
From Summary: "An analytical investigation was made to determine from component performance the effect of turbine stator adjustment on the acceleration characteristics of a typical high-pressure-ratio single-spool turbojet engine. Turbine stator adjustment was adequate to permit engine operation in the intermediate-speed range, but was less satisfactory than the relatively simple schemes of compressor-interstage and -outlet bleed."
Memorandum presenting a study of an acceleration-limiting control on a turbojet engine in order to determine its feasibility as an acceleration control. A proportional-plus-integral type of controller was used in the investigation. Results regarding the one-loop control and two-loop control are provided.
Memorandum presenting an acceleration-limiting control used on a turbojet engine to study the feasibility of its use as an acceleration control. A proportional-plus-integral type of controller was used in this investigation. Results regarding one-loop control and two-loop control are provided.
From Introduction: "This report presents only that portion of the data from the first ditching which was to be used roughly establish the accelerations experienced by the pilot and the amount of water pressure to which the fuselage structure was subjected during the ditching."
From Introduction: "Light-airplane accident data, compiled by Crash Injury Research of Cornell University Medical College, indicate that human beings have often withstood declarations in excess of those imposed in airplane crashes involving extensive damage to the airplane structure (ref. 1). This study also correlates the extent of damage to the airplane structure with the injury incurred by the occupants during crash accidents."
From Introduction: "This report describes some measurements of these quantities obtained by crashing fighter aircraft under circumstances approximating those observed in service."
Report discussung work on accelerometry was done at McCook Field for the purpose of continuing the work done by other investigators and obtaining the accelerations which occur when a high-speed pursuit airplane is subjected to the more common maneuvers. The accelerations obtained in suddenly pulling out of a dive with well-balanced elevators are shown to be within 3 or 4 per cent of the theoretically possible accelerations. The maximum acceleration which a pilot can withstand depends upon the length of time the acceleration is continued. It is shown that he experiences no difficulty under the instantaneous accelerations as high as 7.8 G., but when under accelerations in excess of 4.5 G., continued for several seconds, he quickly loses his faculties.
This report deals with the accelerations obtained in flight on various airplanes at Langley Field for the purpose of obtaining the magnitude of the load factors in flight and to procure information on the behavior of an airplane in various maneuvers. The instrument used in these tests was a recording accelerometer of a new type designed by the technical staff of the National Advisory Committee for Aeronautics. The instrument consists of a flat steel spring supported rigidly at one end so that the free end may be deflected by its own weight from its neutral position by any acceleration acting at right angles to the plane of the spring. This deflection is measured by a very light tilting mirror caused to rotate by the deflection of the spring, which reflected the beam of light onto a moving film. The motion of the spring is damped by a thin aluminum vane which rotates with the spring between the poles of an electric magnet. Records were taken on landings and takeoffs, in loops, spins, spirals, and rolls.
"In connection with the application of stable tricycle-type landing gears to transport airplanes, the question arises as to whether certain passengers may not experience relatively great accelerations in an emergency landing. Since the main landing wheels are behind the center of gravity in this type of gear, a hard-braked landing will cause immediate nosing down of the airplane and, when this motion is stopped due to the front wheel striking the ground, there will be some tendency for the rearmost passengers to be thrown out of their seats, The provided rough calculations are designed to show the magnitudes of the various reactions experienced in a severe landing under these circumstances" (p. 1).
From Introduction: "A study of crash-impact survival in light airplanes is reported in references 1 and 2. A similar study for fighter airplanes is reported in reference 3. This report discusses crash-impact survival in transport airplanes."
Report presenting measurements of a Consolidated B-24D airplane of accelerations at various points on the wing during landing impacts. landings were made with the wheels initially stationary but free to rotate, with the brakes set before contact, and with the main wheels rotating prior to contact.
This dialog allows you to filter your current search.
Each of the Serial/Series Titles listed note their name and the number of records that will be limited down to if you choose that option.
The list can be sorted by name or the count.
Having trouble finding an option within the list of Serial/Series Titles? Start typing and we'll update the list to show only those items that match your needs.
Try limiting with other filters first or use this comprehensive list of titles as an alternative starting point.
This dialog allows you to filter your current search.
Each of the Resource Types listed note their name and the number of records that will be limited down to if you choose that option.
This dialog allows you to filter your current search.
Each of the World Regions listed note their name and the number of records that will be limited down to if you choose that option.
This dialog allows you to filter your current search.
Each of the Countries listed note their name and the number of records that will be limited down to if you choose that option.
This dialog allows you to filter your current search.
Each of the U.S. States listed note their name and the number of records that will be limited down to if you choose that option.
The list can be sorted by name or the count.
This dialog allows you to filter your current search.
Each of the Counties listed note their name and the number of records that will be limited down to if you choose that option.
The list can be sorted by name or the count.
Having trouble finding an option within the list of Counties? Start typing and we'll update the list to show only those items that match your needs.
This dialog allows you to filter your current search.
Each of the Decades listed note their name and the number of records that will be limited down to if you choose that option.
The list can be sorted by name or the count.
This dialog allows you to filter your current search.
Each of the Years listed note their name and the number of records that will be limited down to if you choose that option.
The list can be sorted by name or the count.
Having trouble finding an option within the list of Years? Start typing and we'll update the list to show only those items that match your needs.
This dialog allows you to filter your current search.
Each of the Months listed note their name and the number of records that will be limited down to if you choose that option.
The list can be sorted by name or the count.
This dialog allows you to filter your current search.
Each of the Days listed note their name and the number of records that will be limited down to if you choose that option.
The list can be sorted by name or the count.
Having trouble finding an option within the list of Days? Start typing and we'll update the list to show only those items that match your needs.