UNT Libraries Government Documents Department - 208 Matching Results

Search Results

Results: 1 - 24 next
open access

Aerodynamic Characteristics of a 0.04956-Scale Model of the Convair F-102A Airplane at Transonic Speeds

Description: "Tests have been conducted in the Langley 8-foot transonic tunnel on a 0.04956-scale model of the Convair F-102A airplane which employed an indented and extended fuselage, cambered wing leading edges, and deflected wing tips. Force and moment characteristics were obtained for Mach numbers from 0.60 to 1.135 at angles of attack up to 20 degrees. In addition, tests were made over a limited angle-of-attack range to determine the effects of the cambered leading edges, deflected tips, and a nose sec… more
Date: April 11, 1955
Creator: Tempelmeyer, Kenneth E. & Osborne, Robert S.
Item Type: Refine your search to only Report
open access

Aerodynamic Characteristics of a Circular Cylinder at Mach Number 6.86 and Angles of Attack Up to 90 Degrees

Description: "Pressure-distribution and force tests of a circular cylinder have been made in the Langley 11-inch hypersonic tunnel at a Mach number of 6.86, a Reynolds number of 129,000 based on diameter, and angles of attack up to 90 degrees. The results are compared with the hypersonic approximation of Grimminger, Williams, and Young and with a simple modification of the Newtonian flow theory. The comparison of experimental results shows that either theory gives adequate general aerodynamic characteristic… more
Date: March 11, 1954
Creator: Penland, Jim A.
Item Type: Refine your search to only Report
open access

The aerodynamic characteristics of a supersonic aircraft configuration with a 40 degree sweptback wing through a Mach number range from 0 to 2.4 obtained from various sources

Description: "A summary and analysis have been made of the results of various investigations to determine the aerodynamic characteristics of a supersonic aircraft configuration. The configuration has a wing with 40 degree sweepback at the quarter-chord line, aspect ratio 4, taper ratio 0.5, and 10-percent-thick circular-arc sections normal to the quarter-chord line. Experimental data were available for a Mach number range from 0.16 to 2.32. Results obtained from wing-flow, rocket-model, transonic-bump, and … more
Date: April 11, 1952
Creator: Spearman, M. Leroy & Robinson, Ross B.
Item Type: Refine your search to only Report
open access

Aerodynamic Design of Axial-flow Compressors 6 - Experimental Flow in Two-Dimensional Cascades

Description: "Available experimental two-dimensional cascade data for conventional compressor blade sections are correlated at a reference incidence angle in the region of minimum loss. Variations of reference incidence angle, total-pressure loss, and deviation angle with cascade geometry, inlet Mach number, and Reynolds number are investigated. From the analysis and the correlations of the available data, rules and relations are evolved for the prediction of blade-profile performance" (p. 1).
Date: November 11, 1955
Creator: Lieblein, Seymour
Item Type: Refine your search to only Report
open access

Aerodynamic heating of a wing as determined from a free-flight rocket-model test to Mach number 3.64

Description: From Introduction: "The primary purpose of the wing instrumentation was to obtain data for use in design of NACA research missiles; however, it is believed that the wing is representative of typical supersonic designs and that the data will be of general use and interest. Only the wing data are reported herein."
Date: September 11, 1956
Creator: Swanson, Andrew G. & Rumsey, Charles B.
Item Type: Refine your search to only Report
open access

Aerodynamic Heating of Blunt Nose Shapes at Mach Numbers Up to 14

Description: From Introduction: "The importance of blunt noses as a means of reducing the heat transfer to high velocity missiles has recently received much publicity. The question of just what blunt shape is best is still moot, and it is the purpose of this paper to present and examine some recent experimental results which may throw some light on this problem."
Date: August 11, 1958
Creator: Stoney, William E., Jr.
Item Type: Refine your search to only Report
open access

Aerodynamic heating of blunt nose shapes at Mach numbers up to 14

Description: From Introduction: "The importance of blunt noses as a means of reducing the heat transfer to high velocity missiles has recently received much publicity. The question of just what blunt shape is best is still moot, and it is the purpose of this paper to present and examine some recent experimental results which may throw some light on the problem."
Date: August 11, 1958
Creator: Stoney, William E., Jr.
Item Type: Refine your search to only Report
open access

Aerodynamic study of a wing-fuselage combination employing a wing swept back 63 degrees: Subsonic Mach and Reynolds number effects on the characteristics of the wing and on the effectiveness of an elevon

Description: Report presenting a wind-tunnel investigation of a semispan model of a wing swept back 63 degrees with an aspect ratio of 3.5 and a taper ratio of 0.25. The tests were conducted to evaluate the effects of Reynolds and Mach number on the aerodynamic characteristics of the wing. Results regarding the characteristics of the wing with the elevon undeflected, effectiveness of the elevon, effects of roughness strips, and effect of model deflection under varying loads are provided.
Date: October 11, 1948
Creator: Reynolds, Robert M. & Smith, Donald W.
Item Type: Refine your search to only Report
open access

Altitude performance characteristics of tail-pipe burner with variable-area exhaust nozzle

Description: From Introduction: "Data are presented to show the effects of tail-pipe fuel-air ratio, altitude, and flight Mach number on tail-pipe-burner performance at rated engine speed and approximately constant turbine-outlet temperature. Operational characteristics of the tail-pipe burner and variable-area exhaust nozzle are also reported."
Date: August 11, 1950
Creator: Jansen, Emmert T. & Thorman, H. Carl
Item Type: Refine your search to only Report
open access

Altitude-Wind-Tunnel Investigation of Oil-System Performance of XR-4360-8 Engine in XTB2D-1 Airplane

Description: "An investigation was conducted in the Cleveland altitude wind tunnel to determine the aerodynamic characteristics and the oil delivery critical altitude of the oil-cooler installation of an XTB2D-1 airplane. The investigation was made with the propeller removed end with the engine operating at 1800 brake horsepower, an altitude of 15,000 feet (except for tests of oil-delivery critical altitude), oil-cooler flap deflections from -20 degrees to 20 degrees and inclinations of the thrust axis of 0… more
Date: October 11, 1946
Creator: Conrad, E. William
Item Type: Refine your search to only Report
open access

Altitude-Wind-Tunnel Investigation of Performance of Several Propellers on YP-47M Airplane at High Blade Loading, 1, Aeroproducts H20C-162-X11M2 Four-Blade Propeller

Description: "An investigation was made in the Cleveland Altitude wind tunnel to determine the performance of an Aeroproducts H20C-162-X11M2 four-blade propeller on a YP-47M airplane at high blade loadings and high engine powers. The propeller characteristics were obtained for a range of power coefficients from 0.30 to 1.00 at free-stream Mach numbers of 0.40 and 0.50. The results of the force measurements are indicative only of trends in propeller efficiency with changes in power coefficient and advance-di… more
Date: October 11, 1946
Creator: Saari, Martin J. & Wallner, Lewis E.
Item Type: Refine your search to only Report
open access

Altitude-wind-tunnel investigation of thrust augmentation of a turbojet engine 3: performance with tail-pipe burning in standard-size tail pipe

Description: From Introduction: "Evaluation of tail-pipe burning in this engine with a larger tail-pipe combustion chamber is discussed in reference 1. Results of investigations on tail-pipe burning in this engine at static sea-level conditions are presented in reference 2. An investigation of thrust augmentation by means of injecting water at the inlet of an axial-flow compressor engine is discussed in reference 3."
Date: August 11, 1947
Creator: Fleming, William A. & Golladay, Richard L.
Item Type: Refine your search to only Report
open access

An analysis of available data on effects of wing-fuselage-tail and wing-nacelle interference on the distribution of the air load among components of airplanes

Description: From Introduction: "The purpose of the present paper is to summarize the available data on the effects of wing-fuselage-tail and wing-nacelle interference on the distribution of the air load among aircraft components. Some discussion is also given of the effects of center-of-gravity position."
Date: April 11, 1949
Creator: Wollner, Bertram C.
Item Type: Refine your search to only Report
open access

Analysis of factors affecting selection and design of air-cooled single-stage turbines for turbojet engines 4: coolant-flow requirements and performance of engines using air-cooled corrugated-insert blades

Description: Report presenting an investigation of the estimated minimum cooling requirements and related performance of turbojet engines equipped with high-performance single-stage turbines with air-cooled corrugated-insert blades over a range of turbine-inlet temperature, tip speed, and hub-tip radius ratio for Mach number 2 at 50,000 feet. The effects of stress-ratio factor, flight Mach number, altitude, turbine rotor impeller efficiency, and outside heat-transfer coefficient on cooling requirements were… more
Date: May 11, 1955
Creator: Slone, Henry O. & Hubbartt, James E.
Item Type: Refine your search to only Report
open access

Analysis of Fully Developed Turbulent Heat Transfer at Low Peclet Numbers in Smooth Tubes With Application to Liquid Metals

Description: From Introduction: "Analyses of heat transfer for liquid metals flowing turbulently in smooth tubes (low Pradtl numbers) are given in reference 1 and 2. The predicted heat-transfer coefficients from these analyses are considerably higher than those determined in the experimental heat-transfer investigations for mercury and lead bismuth given in references 2 to 4. If the analytical and experimental results for flow of gases are compared at low Peclet numbers, they are also found to be in disagre… more
Date: August 11, 1952
Creator: Deissler, Robert G.
Item Type: Refine your search to only Report
open access

Analysis of Meteorological Data Obtained During Flight in a Supercooled Stratiform Cloud of High Liquid-Water Content

Description: "Flight icing-rate data obtained in a dense and abnormally deep supercooled stratiform cloud system indicated the existence of liquid-water contents generally exceeding values in amount and extent previously reported over the midwestern sections of the United States. Additional information obtained during descent through a part of the cloud system indicated liquid-water contents that significantly exceeded theoretical values, especially near the middle of the cloud layer. The growth of cloud dr… more
Date: July 11, 1951
Creator: Perkins, Porter J. & Kline, Dwight B.
Item Type: Refine your search to only Report
open access

Analysis of Rocket, Ramjet, Turbojet Engines for Supersonic Propulsion of Long-Range Missiles 2: Rocket Missile Performance

Description: Memorandum presenting an investigation of the theoretical performance of a two-stage ballistic rocket missile with a centerbody and two parallel boosters for JP4-oxygen and ammonia-fluorine propellants. The missile using the ammonia-fluorine propellant weighs about one-half as much as a missile using JP4-oxygen. Results regarding the optimum missile and effect of variation of design parameters are provided.
Date: October 11, 1954
Creator: Huff, Vearl N. & Kerrebrock, Jack
Item Type: Refine your search to only Report
open access

Analytical and experimental studies of a divided-flow ram-jet combustor

Description: From Introduction: "The investigation reported herein is a continuation of a ram-jet-combustor design program being conducted at the NACA Lewis laboratory. The purpose of this broad program is to establish basic design criteria for combustors operating over wide range of fuel-air ratio with low pressure losses and high combustion efficiency, and to utilize these design criteria in the development of practical ram-jet combustors."
Date: January 11, 1954
Creator: Dangle, E. E.; Friedman, Robert & Cervenka, Adolph J.
Item Type: Refine your search to only Report
open access

Analytical determination of local surface heat-transfer coefficients for cooled turbine blades from measured metal temperatures

Description: Analytical methods are presented for the determination of local values of outside and inside heat-transfer coefficients and effective gas temperatures by use of turbine-blade-temperature measurements. The methods are derived for a number of configurations that can be applied to typical cooled-turbine-blade shapes as well as to other types of heat-transfer apparatus.
Date: August 11, 1950
Creator: Brown, W. Byron & Esgar, Jack B.
Item Type: Refine your search to only Report
open access

Automatic control systems satisfying certain general criterions on transient behavior

Description: "An analytic method for the design of automatic controls is developed that starts from certain arbitrary criterions on the behavior of the controlled system and gives those physically realizable equations that the control system can follow in order to realize this behavior. The criterions used are developed in the form of certain time integrals. General results are shown for systems of second order and of any number of degrees of freedom. Detailed examples for several cases in the control of a … more
Date: October 11, 1950
Creator: Boksenbom, Aaron S. & Hood, Richard
Item Type: Refine your search to only Report
Back to Top of Screen