"In the course of an investigation to find a satisfactory vertical tail for the XP-62 airplane, a 0.45-scale vertical tail model on a stub fuselage was tested in the Langley 7- by 10-foot tunnel. This model was fitted with a flat plate to represent the horizontal tail surface. The data are presented herein for their general interest value rather than their application to this particular airplane" (p. 1).
Report presenting an investigation in the two-dimensional low-turbulence tunnels for the purpose of developing an optimum flap configuration for maximum lift on an airfoil section for the Republic XF-12 airplane equipped with a double slotted flap. Lift and flap loads were obtained at several flap deflections for two flap paths. Results regarding lift, drag, and flap loads are provided.
From Introduction: "An investigation of the power-plant installation of a single-engine torpedo-bomber-type airplane has been conducted in the NACA Cleveland altitude wind tunnel at the request of the Bureau of Aeronautics, Navy Department. A similar investigation was previously conducted on a three-tenths scale mock-up of the forward portion of the fuselage of this airplane in the Langley 20-foot tunnel. (See reference 1)."
Report presenting an investigation to determine the effect of the location of the diffuser vanes with respect to the supercharger outlets and the effect of flow conditions at the impeller inlet on the air-flow distribution in the outlets of the engine-stage supercharger of an 18-cylinder double-row radial aircraft engine. The effect of flow conditions at the impeller inlet was investigated by distorting the flow at the inlet and noting the effect in the supercharger outlets. Results regarding the diffuser effect and inlet effect are provided.
From Introduction: "The research program included clean-up tests (unpublished data) and stability and control tests (reference 1) made in the NACA Langley full-scale tunnel. An investigation of the aerodynamic characteristics of the power-plant installation in the Cleveland altitude wind tunnel is discussed in this report."
From Introduction: "The present report has been prepared to discuss the indications obtained from the University of Chicago turbulence indicator in relation to simultaneous measurement of atmospheric gustiness made by the NACA, which are summarized herein."
Availability data obtained on SNB-1 trainer-class airplanes were analyzed and results presented as flight envelopes which predict occurrences of large values of air speed and acceleration. Comparison is made with SNJ-4 trainer-class airplane data analyzed by the same method. It is concluded that flight envelopes are satisfactory; that the two types show large differences in flight loads and speeds experience; and that SNB-1 will seldom, if ever, exceed design limit load factor and restricted speed, which SNJ-4 can be expected to exceed design-limit load factor and restricted speed in a very small number of flight hours.
Report discusses calibration testing performed on a Kollsman type G-1 and an NAF No. 1 pitot tube at several Mach numbers and angles of attack. The effect of drain holes on the flow within the pitot tube was analyzed and the ability to estimate the error in the total pressure was created. The accuracy of the extrapolated and estimated values were found to be within reasonable limits.
"A relatively simple equation has been found to express with fair accuracy, variation in manifold-charge temperature with charge in engine operating conditions. This equation and associated curves have been checked by multi cylinder-engine data, both test stand and flight, over a wide range of operating conditions. Average mixture temperatures, predicted by the equations of this report, agree reasonably well with results within the same range of carburetor-air temperatures from laboratories and test stands other than the NACA" (p. 1).
Behaviors of both model and full-scale airplanes were ascertained by making visual observations, by recording time histories of decelerations, and by taking motion picture records of ditchings. Results are presented in form of sequence photographs and time-history curves for attitudes, vertical and horizontal displacements, and longitudinal decelerations. Time-history curves for attitudes and horizontal and vertical displacements for model and full-scale tests were in agreement; maximum longitudinal decelerations for both ditchings did not occur at same part of run; full-scale maximum deceleration was 50 percent greater.
Report presenting testing to determine the best way to land the SB2C-1 airplane in calm and rough water and to determine its probable ditching performance. The behavior of the model was determined by making visual observations and by recording the maximum longitudinal decelerations and by taking motion pictures of the ditchings. Results regarding the effect of flaps, attitude, weight, a wing-low landing, effect of simulated damage, effect of tail wheel, ditching aids, and seaway are provided.
Report presenting the performance of a 22-inch-diameter pulse-jet engine using a net of low-loss modified air valves at ram pressures equivalent to simulated flight speeds. Results regarding combustion-air weight flow, flight thrust, maximum combustion-chamber pressure, specific fuel consumption, pressure cycle, and valve life are provided.
Report discussing testing to determine the effect of ethylene dibromide on the knock-limited performance of S reference fuel. An increase in ethylene-dibromide content did appear to decrease the knock-limited performance of the fuel up to a certain point and at all but the extremes of fuel-air mixtures.
Report discussing testing on 22 inch-diameter pulse-jet engines to determine the effect on performance of a change in combustion-air temperature from approximately 80 degrees to 130 degrees. The effects on jet thrust, combustion-air flow, and engine thrust are described.
Report discussing the results of accelerated erosion tests to determine the separate effects of the passage of fuel, water, and ice particles through a supercharger. Recommendations for preventing erosion are provided, including materials choice and joint design.
Report discussing the effects of various inlet pressures, inlet temperatures, wheel speeds, pressure ratios, and cooling-air flows on the performance of a radial-flow exhaust-gas turbosupercharger turbine with a 12.75-inch tip diameter. Information about efficiency is provided for a given blade-to-jet speed ratio.
Report discussing an investigation of the knock-limited performance of triptane in F-3 and F-4 rating engines, two full-scale air-cooled aircraft cylinders, and flight tests on a full-scale multicylinder engine. Information about the lead susceptibility and effect of engine operating conditions is also provided.
Data are presented of the flow conditions in the vicinity of an NACA D sub S -type cowling. Tests were made of a 1/2 scale-nacelle model at inlet-velocity ratios ranging from 0.23 to 1.02 and angles of attack from 6 deg to 10 deg. The velocity and direction of flow in the vertical plane of symmetry of the cowling were determined from orifices and tufts installed on a board aligned with the flow. Diagrams showing velocity ratio contours and lines of constant flow angles are given.
"Flight tests of an A-26B airplane have been conducted to determine the changes in maximum speed, as affected by changes in carburetor ram and aerodynamic refinement of the nacelles, resulting from the addition of sealed spinners and modification of the charge air system, cowling, and nacelle afterbodies. The changes in nacelle drag resulting from these modifications were measured independently by means of a revolving wake survey rake behind the nacelle and boundary layer rakes on the cowling, and provide a quantitative check of the speed measurements as well as a means of analyzing the components of nacelle drag" (p. 1).
Results of flight tests of a control-feel aid presented. This device consisted of a spring and dashpot connected in series between the control stick and airplane structure. The device was tested in combination with an experimental elevator and bobweight which had given unsatisfactory dynamic stability and control-feel characteristics in previous tests. The control-feel aid effected marked improvement in both the control-feel characteristics and the control-feel dynamic longitudinal stability of the airplane.
Report discussing measurements of the overall drag coefficient of the XP-51 in dives using three different methods. The three instruments used to measure drag variation are compared for accuracy. A comparison of the drag results obtained from this test are also compared to the results obtained from previous wind tunnel testing.
Report discussing testing on the spin and recovery characteristics, longitudinal-trimming characteristics at extreme angles of attack, and tumbling characteristics of a model of the Cornelius XFG-1 glider. The effects of loading, mass distribution, and center-of-gravity position were determined. They also explored the inverted spin characteristics and spin-recovery parachute requirements.
Report discussing an investigation of the cooling characteristics of an R-2600-22 engine installed in a PBM-3D nacelle. The investigation explored the general cooling characteristics by the NACA cooling-correlation method and an investigation of specific points on the engine cylinder where cooling was critical, including the exhaust-valve-crown and number 3 cylinder.
Report discussing an investigation into several types and sizes of flaps and spoilers located forward of the elevators on the upper surface of the horizontal stabilizer of a model of a radial-engine pursuit airplane. Information about the elevator characteristics, elevator-fixed and elevator-free balance lift coefficient, and trim drag coefficient for a range of Mach numbers is provided.
Report discussing the aerodynamic characteristics of a twin-fuselage pursuit airplane model, especially at high speeds. Information about the force data and critical Mach numbers for parts of the model is provided. Suggestions for increasing the Mach number of divergence by making modifications to the wing-fuselage fillets and external shape of the radiator are also included.
Report discussing a mock-up injection impeller created to investigate the hydraulic characteristics and limitations of the NACA injection impeller currently in use. Information about the form and magnitude of critical factors of fuel-transfer leakage and peripheral fuel distribution is provided as well as the effects of design variations of components on hydraulic characteristics. Several revisions in portions of the impeller are suggested to improve its fuel-transfer, fuel-pumping, and fuel-equalizing characteristics.
Report discussing an investigation into cowl-flap and cowl-outlet designs for the B-29 in order to determine the effects of cowling performance of different types of flaps and elements of flaps. Details of the available pressure drop and cooling-air pressure-drop distribution are also provided.
Report investigating five cowl-inlet configurations for the B-29 to obtain design information for improving the cowl performance. The effects of propeller spinners and increased inlet diameters on the cooling-air pressures at the cowl inlet and face of the engine and on the drag and critical speed of the cowl are described.
"Ground tests were conducted on a twin-engine fighter airplane to study icing of an induction system incorporating an exhaust-driven turbosupercharger. The ground tests were made to determine the disposition of free water in the induction system of the airplane, to determine the charge-air heat rise available from the turbosupercharger, and to correlate actual airplane-test results with those of laboratory tests" (p. 1).
"Flight tests were conducted on a twin-engine fighter airplane at pressure altitudes up to 10,000 feet with simulated conditions of moderate, heavy, and excessive rain to determine the increase in enthalpy of the charge air due to the turbosupercharger, to determine the rate of enthalpy increase of the charge air resulting from a sudden increase of engine power, and to compare the conditions that caused induction-system icing in flight with those that resulted in icing of the same carburetor and supercharger inlet elbow in laboratory tests" (p. 1).
"In order to eliminate the formation of ice on the carburetor throttle plates of an aircraft-engine induction system, two modifications of the throttle design and a variation in the method of throttle operation of the twin-barrel injection carburetor were tested" (p. 1). The modifications were investigated under severe icing conditions at normal power, maximum cruising power, and 60-percent normal power. The only modification that appeared to provide deicing assistance were the electrically heated throttle plates.
Report discussing modifications to the spray nozzle to prevent the formation of refrigeration icing in the induction system of an aircraft engine. Two fuel-injection systems, a spinner type and a drilled-inducer type, that prevent the formation of refrigerator icing satisfactorily were created.
Report discussing the icing characteristics of a rectangular-throat pressure-type carburetor. Serious ice was not found to form under the conditions of this particular test, although visible ice and frost formed in certain areas.
"A preliminary analysis has been made of the conditions of stability of free oscillations of a hinged rotor in hovering flight. The case analyzed is a rotor with hinges allowing freedom in flapping and lagging and having a completely reversible cyclic pitch-control system, so that a twisting moment on a blade moves the control stick without hindrance from spring or friction constraint. The principal results of this study are presented in the form of a stability chart" (p. 1).
Report discussing a series of single-cylinder engine tests to determine the effect of special surface coatings in porous chrome-plated cylinder barrels on oil consumption and ring wear. The coating materials were selected for their bearing and lubrication properties and on their applicability to processing. The surface coatings tested were lead overplates, silver overplates, and colloidal graphite base paint.
Report presenting a series of single-cylinder engine tests run to determine a satisfactory method of reducing oil consumption in radial air-cooled engines with flat-face compression rings as standard parts and equipped with cylinder barrels salvaged by porous chrome plating. Testing was conducted using porous chrome-plated cylinders with straight and choke bores with standard flat-face compression rings.
Report discussing several types of jet-exit designs, including normal, beveled, and unsymmetrical shapes, and their effect on the stability characteristics of the aircraft. No deviation of the jet center line from its exposed path is likely to be obtained if a jet exist is used that is normal to the flow. Having a tilted or asymmetrical exit was found to adversely affect the stability of the aircraft.
An investigation was conducted to compare the performance of two 25-ft-diam rotors which had identical dimensions and were similar in construction but different in blade airfoil-sections. Tests were conducted at indicated blade pitch angles from 3 degrees to 11.5 degrees and rotor speeds of 200, 290, and 371 rpm. The 23012.6 rotor required 2 percent less power to hover than the 0012.6. At thrust coefficients above design, the performance of the 23012.6 became better than the 0012.6 rotor.
Report presenting testing of a double-row radial air-cooled engine to investigate overall cooling characteristics and to analyze what variations in temperature distribution were caused by variations in cooling-air pressure drop, power, and fuel-air ratio. Testing occurred over a range of engine powers.
Report discussing testing of a model of the Kaiser tailless airplane in order to determine its general aerodynamic characteristics and the probable stability and control characteristics. Only the results of the tests are presented in this report; the estimated flying qualities are in a separate report. Information about the lift, stall, drag, elevator effectiveness and hinge moments, rudder effectiveness and hinge moments, aileron effectiveness and hinge moments, and characteristics in yaw is included.
From Summary: "A 1/7 scale semispan model of the XB-35 airplane was tested in the Langley 10 foot pressure tunnel, primarily for the purpose of investigating the effectiveness of a leading-edge slot for alleviation of stick-fixed longitudinal instability at high angles of attack caused by early tip stalling and a device for relief of stick-free instability caused by elevon up-floating tendencies at high angles of attack. Results indicated that the slot was not adequate to provide the desired improvement in stick-fixed stability."
"A machined mixed-flow centrifugal impeller of a relatively complex passage shape was used as a pattern to cast a number of aluminum-alloy impellers from two aluminum-base alloys (designated alloys 1 and 2) by the 'lost wax' process. An investigation was conducted to determine whether these cast impellers, could be considered satisfactory for use in compressors. The investigation included preliminary examination, physical tests, metallurgical examination, and performance tests" (p. 1).
Report discussing the characteristics of the jet-motor air-intake duct system for a pursuit-type airplane with modifications to the duct system. Details of its effects on the Mach number, high pressure recovery, drag, and simplicity of the system are provided. Problems regarding the flow condition through the ducts and some potential modifications to prevent further issues are also described.
Report discussing the results of testing to determine the aerodynamic characteristics of three NACA-designed airfoil sections, some with flaps equipped. The tests included determination of the aerodynamic characteristics of the airfoils in smooth conditions and with standard roughness applied to the leading edge. Lift tests were also carried out at a range of flap deflections.
This dialog allows you to filter your current search.
Each of the Serial/Series Titles listed note their name and the number of records that will be limited down to if you choose that option.
This dialog allows you to filter your current search.
Each of the World Regions listed note their name and the number of records that will be limited down to if you choose that option.
This dialog allows you to filter your current search.
Each of the Countries listed note their name and the number of records that will be limited down to if you choose that option.
This dialog allows you to filter your current search.
Each of the U.S. States listed note their name and the number of records that will be limited down to if you choose that option.
This dialog allows you to filter your current search.
Each of the Counties listed note their name and the number of records that will be limited down to if you choose that option.
This dialog allows you to filter your current search.
Each of the Months listed note their name and the number of records that will be limited down to if you choose that option.
The list can be sorted by name or the count.
This dialog allows you to filter your current search.
Each of the Days listed note their name and the number of records that will be limited down to if you choose that option.