UNT Libraries - 103 Matching Results

Search Results

prev Results: 61 - 84 next
open access

Investigation of Immersion Cooled ARM-Based Computer Clusters for Low-Cost, High-Performance Computing

Description: This study aimed to investigate performance of ARM-based computer clusters using two-phase immersion cooling approach, and demonstrate its potential benefits over the air-based natural and forced convection approaches. ARM-based clusters were created using Raspberry Pi model 2 and 3, a commodity-level, single-board computer. Immersion cooling mode utilized two types of dielectric liquids, HFE-7000 and HFE-7100. Experiments involved running benchmarking tests Sysbench high performance linpack (H… more
Date: August 2017
Creator: Mohammed, Awaizulla Shareef
Item Type: Refine your search to only Thesis or Dissertation
open access

Investigation of Spray Cooling Schemes for Dynamic Thermal Management

Description: This study aims to investigate variable flow and intermittent flow spray cooling characteristics for efficiency improvement in active two-phase thermal management systems. Variable flow spray cooling scheme requires control of pump input voltage (or speed), while intermittent flow spray cooling scheme requires control of solenoid valve duty cycle and frequency. Several testing scenarios representing dynamic heat load conditions are implemented to characterize the overall performance of variable… more
Date: May 2017
Creator: Yata, Vishnu Vardhan Reddy
Item Type: Refine your search to only Thesis or Dissertation
open access

Investigation of the feasibility of non-invasive carbon dioxide detection using spectroscopy in the visible spectrum.

Description: Pulse oximeters are used in operating rooms and recovery rooms as a monitoring device for oxygen in the respiratory system of the patient. The advantage of pulse oximeters over other methods of oxygen monitoring is that they are easy to use and they are non-invasive, which means it is not necessary break the skin to extract blood for information to be obtained. The standard for the measurement of partial pressure of CO2 and O2 is an arterial blood gas analysis (ABG). However routine monitoring … more
Date: December 2007
Creator: Marks, Damian
Item Type: Refine your search to only Thesis or Dissertation
open access

Knowledge Based System and Decision Making Methodologies in Materials Selection for Aircraft Cabin Metallic Structures

Description: Materials selection processes have been the most important aspects in product design and development. Knowledge-based system (KBS) and some of the methodologies used in the materials selection for the design of aircraft cabin metallic structures are discussed. Overall aircraft weight reduction means substantially less fuel consumption. Part of the solution to this problem is to find a way to reduce overall weight of metallic structures inside the cabin. Among various methodologies of materials … more
Date: August 2016
Creator: Adhikari, Pashupati Raj
Item Type: Refine your search to only Thesis or Dissertation
open access

Laser Cutting Machine: Justification of initial costs

Description: The Industrial Laser is firmly established in metalcutting as the tool of choice for many applications. The elevator division of Montgomery KONE Inc., in an effort to move towards quality, ontime, complete deliveries and 100% customer satisfaction, decided to invest in new equipment to improve manufacturing processes. A huge investment is proposed for a laser-cutting machine. It is the responsibility of Manufacturing Engineering to direct the management by justifying its benefits, which include… more
Date: May 2001
Creator: Nagaraja, Dwarakish
Item Type: Refine your search to only Thesis or Dissertation
open access

Linearity and monotonicity of a 10-bit, 125 MHz, segmented current steering digital to analog converter

Description: The purpose of this research is to determine the linearity and monotonicity of the THS5651IDW digital to analog converter (DAC), a prototype of the future Texas Instruments TLV5651, 10-bit, 125 MHz communication DAC. Testing was conducted at the Texas Instruments facility on Forest Lane, Dallas, Texas. Texas Instruments provided test equipment, software and laboratory space to obtain test data. Analysis of the data found the DAC to be monotonic since the magnitude of the differential nonlineari… more
Date: May 2000
Creator: Bittle, Charles C.
Item Type: Refine your search to only Thesis or Dissertation
open access

Liquid Nitrogen Propulsion Systems for Automotive Applications: Calculation of Mechanical Efficiency of a Dual, Double-acting Piston Propulsion System

Description: A dual, double-acting propulsion system is analyzed to determine how efficiently it can convert the potential energy available from liquid nitrogen into useful work. The two double-acting pistons (high- and low-pressure) were analyzed by using a Matlab-Simulink computer simulation to determine their respective mechanical efficiencies. The flow circuit for the entire system was analyzed by using flow circuit analysis software to determine pressure losses throughout the system at the required mas… more
Date: May 2008
Creator: North, Thomas B.
Item Type: Refine your search to only Thesis or Dissertation
open access

MBE Growth and Instrumentation

Description: This thesis mainly aims at application of principles of engineering technology in the field of molecular beam epitaxy (MBE). MBE is a versatile technique for growing epitaxial thin films of semiconductors and metals by impinging molecular beams of atoms onto a heated substrate under ultra-high vacuum (UHV) conditions. Here, a LabVIEW® (laboratory virtual instrument engineering workbench) software (National Instruments Corp., http://www.ni.com/legal/termsofuse/unitedstates/usH) program is dev… more
Date: May 2006
Creator: Tarigopula, Sriteja
Item Type: Refine your search to only Thesis or Dissertation
open access

The Measurement of the Third-order Elastic Constants for La3ga5sio14 (Lgs) and La3ga55ta05o14 (Lgt) Single Crystal

Description: Recently, the development of electronic technology towards higher frequencies and larger band widths has led to interest in finding new piezoelectric materials, which could be used to make filters with larger pass band widths and oscillators with better frequency stability. Langasite (La3Ga5SiO14, LGS) and its isomorphs have enticed considerable attention of researchers as a potential substrate material for piezoelectric device applications because of its high frequency stability and fairly goo… more
Date: December 2013
Creator: Karim, Md Afzalul
Item Type: Refine your search to only Thesis or Dissertation
open access

Mechanical Characterization of A2 and D2 Tool Steels By Nanoindentation

Description: Nanoindentation technique was used to investigate the surface properties of A2 and D2 tool steel subjected to different heat treatments. the mechanical characteristics of these two easily available tool steels were studied based on microstructural images obtained from SEM, the grain growth after heat treatment using X-ray diffraction method and nanoindentation technique. the investigation showed that a single nanoindentation result can explain how heat treatment influences reliability and failu… more
Date: May 2012
Creator: Okafor, Uzochukwu Chimezie
Item Type: Refine your search to only Thesis or Dissertation
open access

Micro-fabrication of a Mach-Zehnder interferometer combining laser direct writing and fountain pen micropatterning for chemical/biological sensing applications.

Description: This research lays the foundation of a highly simplified maskless micro-fabrication technique which involves incorporation of laser direct writing technique combined with fountain pen based micro-patterning method to fabricate polymer-based Mach-Zehnder interferometer sensor arrays' prototype for chemical/biological sensing applications. The research provides methodology that focuses on maskless technology, allowing the definition and modification of geometric patterns through the programming … more
Date: May 2009
Creator: Kallur, Ajay
Item Type: Refine your search to only Thesis or Dissertation
open access

Microfluidic-Based Fabrication of Photonic Microlasers for Biomedical Applications

Description: Optical microlasers have been used in different engineering fields and for sensing various applications. They have been used in biomedical fields in applications such as for detecting protein biomarkers for cancer and for measuring biomechanical properties. The goal of this work is to propose a microfluidic-based fabrication method for fabricating optical polymer based microlasers, which has advantages, over current methods, such us the fabrication time, the contained cost, and the reproducibil… more
Date: December 2019
Creator: Cavazos, Omar
Item Type: Refine your search to only Thesis or Dissertation
open access

Mist Characterization in Drilling 1018 Steel

Description: Minimum quantity lubrication replaces the traditional method of flood cooling with small amounts of high-efficient lubrication. Limited studies have been performed to determine the characteristics of mist produced during MQL. This study investigated the mist concentration levels produced while drilling 1018 steel using a vegetable based lubricant. ANOVA was performed to determine whether speed and feed rates or their interactions have a significant effect on mist concentration levels and partic… more
Date: August 2012
Creator: Cole, Ian
Item Type: Refine your search to only Thesis or Dissertation

A model for designing a new telecommunication system in Mongolia

Description: The objective of this research is to design, and determine the feasibility of, a telecommunication system for the city of Erdenet, Mongolia. The Mongolian Telecommunication Company, Telecommunication Company of Erdenet city, and the National Statistical Office of Mongolia provided the data required for telecommunication forecasting of Erdenet. The literature review and analysis of the telecommunication forecasting indicate the need for a model of a new Telecommunication system in Erdenet, Mongo… more
Access: Restricted to UNT Community Members. Login required if off-campus.
Date: May 2001
Creator: Baatarjav, Enkhbat
Item Type: Refine your search to only Thesis or Dissertation

Modeling and Analysis of Prototype Shelter Structure on Abaqus

Description: Due to the constraint of high costs and limitations of load conditions, experimental testing is not appropriate for the static study of shelter structures. Comparatively, an effective computational modeling and numerical solution demonstrates significant advantages for understanding the response of steel shelter structures. This study gives an insight into the structural integrity of the prototype shelter structure which is examined using computer simulation of the shelter structure on Abaqus/C… more
Date: August 2020
Creator: Rao, Noraiz
Item Type: Refine your search to only Thesis or Dissertation

Nodal Resistance Measurement System

Description: The latest development in the measurement techniques has resulted in fast improvements in the instruments used for measurement of various electrical quantities. A common problem in such instruments is the automation of acquiring, retrieving and controlling the measurements by a computer or a laptop. In this study, nodal resistance measurement (NRM) system is developed to solve the above problem. The purpose of this study is to design and develop a compact electronic board, which measures elect… more
Access: Restricted to the UNT Community Members at a UNT Libraries Location.
Date: May 2005
Creator: Putta, Sunil Kumar
Item Type: Refine your search to only Thesis or Dissertation
open access

Nominal Shear Strength and Seismic Detailing of Cold-formed Steel Shear Walls using Steel Sheet Sheathing

Description: In this research, monotonic and cyclic tests on cold-formed steel shear walls sheathed with steel sheets on one side were conducted to (1) verify the published nominal shear strength for 18-mil and 27-mil steel sheets; and (2) investigate the behavior of 6-ft. wide shear walls with multiple steel sheets. In objective 1: this research confirms the discrepancy existed in the published nominal strength of 27-mil sheets discovered by the previous project and verified the published nominal strength … more
Date: August 2010
Creator: Chen, Yujie
Item Type: Refine your search to only Thesis or Dissertation
open access

Nominal Shear Strength of Cold-formed Steel Shear Walls Using Osb Sheathing

Description: In the cold-formed steel construction, the oriented strand board is a common material for shear wall sheathing. an OSB is made by using wood chips as raw materials that undergo high temperature pressing to create a multi-larger structure material. Due to the OSB having a high strength in shear, it is an important material used in the construction field. the thesis is trying to verify published nominal shear strength in AISI-213-07 in the first part. This objective has two parts: the first part … more
Date: May 2012
Creator: Li, Chao
Item Type: Refine your search to only Thesis or Dissertation
open access

Ota-quadrotor: An Object-tracking Autonomous Quadrotor for Real-time Detection and Recognition

Description: The field of robotics and mechatronics is advancing at an ever-increasing rate and we are starting to see robots making the transition from the factories to the workplace and homes as cost is reduced and they become more useful. In recent years quadrotors have become a popular unmanned air vehicle (UAV) platform. These UAVs or micro air vehicles (MAV) are being used for many new and exciting applications such as aerial monitoring of wildlife, disaster sites, riots and protests. They are also be… more
Date: May 2012
Creator: Coelho, Gavin
Item Type: Refine your search to only Thesis or Dissertation
open access

Preliminary design of a cryogenic thermoelectric generator.

Description: A cryogenic thermoelectric generator is proposed to increase the efficiency of a vehicle propulsion system that uses liquid nitrogen as its fuel. The proposed design captures some of the heat required for vaporizing or initial heating of the liquid nitrogen to produce electricity. The thermoelectric generator uses pressurized liquid nitrogen as its cold reservoir and ambient air as the high-temperature reservoir to generate power. This study concentrated on the selection of thermoelectric mater… more
Date: May 2007
Creator: Sivapurapu, Sai Vinay Kumar
Item Type: Refine your search to only Thesis or Dissertation
open access

Propagation analysis of a 900 MHz spread spectrum centralized traffic signal control system.

Description: The objective of this research is to investigate different propagation models to determine if specified models accurately predict received signal levels for short path 900 MHz spread spectrum radio systems. The City of Denton, Texas provided data and physical facilities used in the course of this study. The literature review indicates that propagation models have not been studied specifically for short path spread spectrum radio systems. This work should provide guidelines and be a useful ex… more
Date: May 2006
Creator: Urban, Brian L.
Item Type: Refine your search to only Thesis or Dissertation
open access

Radio frequency propagation differences through various transmissive materials.

Description: The purpose of this research was to determine which of the commonly used wireless telecommunication site concealment materials has the least effect on signal potency. The tested materials were Tuff Span® fiberglass panels manufactured by Enduro Composite Systems, Lexan® XL-1 polycarbonate plastic manufactured by GE Corporation and Styrofoam™ polystyrene board manufactured by The Dow Chemical Company. Testing was conducted in a double electrically isolated copper mesh screen room at the Univer… more
Date: December 2002
Creator: Ryan, Patrick L.
Item Type: Refine your search to only Thesis or Dissertation
open access

Recommended Modified zone Method Correction Factor for Determining R-values of Cold-Formed Steel Wall Assemblies

Description: Currently, ASHRAE has determined the zone method and modified zone method are appropriate calculation methods for materials with a high difference in conductivity, such as cold-formed steel (CFS) walls. Because there is currently no standard U-Factor calculation method for CFS walls, designers and code officials alike tend to resort to the zone method. However, the zone method is restricted to larger span assemblies because the zone factor coefficient is 2.0. This tends to overestimate the amou… more
Date: May 2011
Creator: Black, John
Item Type: Refine your search to only Thesis or Dissertation
open access

Seismic Performance Evaluation of Novel Cold-Formed Steel Framed Shear Walls Sheathed with Corrugated Steel Sheets

Description: This thesis presents experiments and numerical analysis of a novel cold-formed steel framed shear wall sheathed with corrugated steel sheets. The objective of this newly designed shear wall is to meet the growing demand of mid-rise buildings and the combustibility requirement in the International Building Code. The strength of the novel shear wall is higher than currently code certified shear wall in AISI S400-15 so that it could be more favorable for mid-rise building in areas that are prone t… more
Date: August 2017
Creator: Lan, Xing
Item Type: Refine your search to only Thesis or Dissertation
Back to Top of Screen