UNT Libraries - 58 Matching Results

Search Results

Results: 1 - 24 next
open access

Characterization of Boron Nitride Thin Films on Silicon (100) Wafer.

Description: Cubic boron nitride (cBN) thin films offer attractive mechanical and electrical properties. The synthesis of cBN films have been deposited using both physical and chemical vapor deposition methods, which generate internal residual, stresses that result in delamination of the film from substrates. Boron nitride films were deposited using electron beam evaporation without bias voltage and nitrogen bombardment (to reduce stresses) were characterize using FTIR, XRD, SEM, EDS, TEM, and AFM technique… more
Date: August 2007
Creator: Maranon, Walter
Item Type: Refine your search to only Thesis or Dissertation

Characterization of Iron Oxide Deposits Formed at Comanche Peak Steam Electric Station

Description: The presence of deposits leading to corrosion of the steam generator (SG) systems is a major contributor to operation and maintenance cost of pressurized water reactor (PWR) plants. Formation and transport of corrosion products formed due to the presence of impurities, metallic oxides and cations in the secondary side of the SG units result in formation of deposits. This research deals with the characterization of deposit samples collected from the two SG units (unit 1 and unit 2) at Comanche P… more
Access: Restricted to the UNT Community Members at a UNT Libraries Location.
Date: May 2003
Creator: Namduri, Haritha
Item Type: Refine your search to only Thesis or Dissertation

Cold-Formed Steel Member Connections Using BAC Screw Fasteners

Description: In this project, the main research objective is intend to seek criteria for evaluating the capacity of BAC screw fasteners with mixed configuration of waterproof seal washer, sealer tape and different pre-drill holes to determine shear and tension strength values for the screws used in cold-formed steel connections. The thesis presents the design methods and test program conducted to investigate the behavior and strength of the screw connections in shear and tension test. Test results were comp… more
Access: Restricted to UNT Community Members. Login required if off-campus.
Date: May 2019
Creator: Li, Xun
Item Type: Refine your search to only Thesis or Dissertation
open access

A Computer-Based Process Control System for a Target Station in a LINAC Facility

Description: An event-driven, sequential, process control system was designed for International Isotopes, Inc., to automate and remotely control a target station at the company's linear accelerator facility. The designed system consisted of two major sections: a software program (virtual instrument), which was developed by LabVIEW, and a hardware interface (FieldPoint Modular Distributed I/O System by National Instrument), which had to be a pre-developed system that did not require customization. The design… more
Date: May 1999
Creator: Al-Shantaf, Abdulraouf O.
Item Type: Refine your search to only Thesis or Dissertation
open access

Computer Virus Spread Containment Using Feedback Control.

Description: In this research, a security architecture based on the feedback control theory has been proposed. The first loop has been designed, developed and tested. The architecture proposes a feedback model with many controllers located at different stages of network. The controller at each stage gives feedback to the one at higher level and a decision about network security is taken. The first loop implemented in this thesis detects one important anomaly of virus attack, rate of outgoing connection. Tho… more
Date: December 2004
Creator: Yelimeli Guruprasad, Arun
Item Type: Refine your search to only Thesis or Dissertation

Construction Management Methods and Techniques in Army Tactical Shelter

Description: This thesis presents a research effort aimed at developing using construction methods and techniques in army tactical shelter. The beginning step focuses on developing and identifying different activities and work breakdown structure applicable in shelter prototype. The next step focuses on identifying resource allocation. This include allocate resources based on the delivered project as per alternative one and for the second alternative as optimization, resource allocation modified and tried t… more
Access: Restricted to UNT Community Members. Login required if off-campus.
Date: December 2019
Creator: Yeganehtalab, Babak
Item Type: Refine your search to only Thesis or Dissertation
open access

Cost Savings Realized Through Proper Sizing of an Excessive Instrument Air System.

Description: The purpose of this research was to determine if installing a smaller air compressor could reduce the electrical usage of a large semiconductor manufacturing plant. A 200 horsepower Atlas Copco compressor was installed with the existing 500 horsepower Ingersoll-Rand compressors. Testing was conducted during the regular manufacturing process at MEMC Southwest in Sherman, Texas. Analysis of the data found that installing the new compressor could reduce electrical consumption. The study also found… more
Date: December 2003
Creator: Condron, Ewell D.
Item Type: Refine your search to only Thesis or Dissertation
open access

A Data Acquisition System Experiment for Gas Temperature and Pressure Measurements on a Liquid-Nitrogen-Powered Vehicle

Description: A data acquisition system was set up to measure gas temperatures and pressures at various points on a liquid-nitrogen-powered vehicle. The experiment was attempted to develop a data acquisition method for applications on engines that use liquid air as the fuel. Two thermocouples and a pressure transducer were connected using data acquisition instruments interfaced to a laptop computer to acquire data.
Date: May 1998
Creator: Lui, Samson Sze-Sang
Item Type: Refine your search to only Thesis or Dissertation
open access

The Design and Development of Lightweight Composite Wall, Roof, and Floor Panels for Rigid Wall Shelter

Description: This thesis presents a research effort aimed at developing a stronger, lighter, and more economic shelter using rigid wall panels. Reported herein is insulation research, wall and roof panel design and testing, floor section modeling and strength calculations, and cost and weight calculations. Beginning stages focus on developing solid wall and roof panels using cold-formed steel corrugated sheathing and members, as well as polyurethane spray foam for insulation. This research includes calculat… more
Date: May 2018
Creator: Artman, Jeremy J
Item Type: Refine your search to only Thesis or Dissertation

Design Method for Cold-Formed Steel Shear Wall Sheathed with Polymer Composite Panel

Description: In order to predict the strength of shear wall with cold-formed steel framing members, analytical models were reviewed. Multiple analytical models were studied, as well as twenty-one connection tests were performed. The connection tests consist of 50-ksi cold-formed steel framing track, different fastening configurations, and different sheathing thicknesses (1/8" and 1/2"). No.12 screw resulted in the highest peak load of all fastening configurations, while the rivet connection had the lowest p… more
Date: August 2020
Creator: Dewaidi, Mohaned Ali
Item Type: Refine your search to only Thesis or Dissertation

Design Method of Cold-Formed Steel Framed Shear Wall Sheathed by Structural Concrete Panel

Description: The objective of this research is developing a new method of design for cold-formed steel framed shear wall sheathed by ¾" thick USG structural panel concrete subfloor using a predictive analytical model and comparing the results obtained from the model with those achieved from real testing to verify the analytical model and predicted lateral load-carrying capacity resulted from that. Moreover, investigating the impact of various screw spacings on shear wall design parameter such as ultimate st… more
Access: Restricted to UNT Community Members. Login required if off-campus.
Date: December 2019
Creator: Ashkanalam, Aida
Item Type: Refine your search to only Thesis or Dissertation
open access

Design, Modeling, and Experiment of a Piezoelectric Pressure Sensor based on a Thickness-Shear Mode Crystal Resonator

Description: This thesis presents the design, modeling, and experiment of a novel pressure sensor using a dual-mode AT-cut quartz crystal resonator with beat frequency analysis based temperature compensation technique. The proposed sensor can measure pressure and temperature simultaneously by a single AT-cut quartz resonator. Apart from AT-cut quartz crystal, a newly developed Langasite (LGS) crystal resonator is also considered in the proposed pressure sensor design, since LGS can operate in a higher tempe… more
Date: May 2017
Creator: Pham, Thanh Tuong
Item Type: Refine your search to only Thesis or Dissertation
open access

Design of a Monitoring System for a Plasma Cleaning Machine

Description: Plasma cleaning is the most effective dry process to remove surface contaminates from a SAW (Surface Acoustical Wave) device. Consistent gas pressures, flows, and good electrical connections between the chamber shelves are necessary for the process to function predictably. In addition, operation of the monitoring system must be transparent to the plasma cleaning unit. This thesis describes a simple solution to the complex problem of monitoring a plasma cleaning system. The monitoring system use… more
Date: May 1999
Creator: Fooks, Terry M. (Terry Max)
Item Type: Refine your search to only Thesis or Dissertation

Design of Power Amplifier Test Signals with a User-Defined Multisine

Description: Cellular radio communication involves wireless transmission and reception of signals at radio frequencies (RF). Base stations house equipment critical to the transmission and reception of signals. Power amplifier (PA) is a crucial element in base station assembly. PAs are expensive, take up space and dissipate heat. Of all the elements in the base station, it is difficult to design and operate a power amplifier. New designs of power amplifiers are constantly tested. One of the most important co… more
Access: Restricted to UNT Community Members. Login required if off-campus.
Date: May 2004
Creator: Nagarajan, Preeti
Item Type: Refine your search to only Thesis or Dissertation
open access

Determination of the Shelf Life of Aluminum Electrolytic Capacitors.

Description: The aluminum electrolytic capacitor is used extensively in the electric utility industry. A factor limiting the storage of spare capacitors is the integrity of the aluminum oxide dielectric, which over time breaks down contributing to a shelf life currently estimated at one nuclear power electric generating station to be approximately five years. This project examined the electrical characteristics of naturally aged capacitors of several different styles to determine if design parameters were… more
Date: May 2002
Creator: Wynne, Edward McFaddin
Item Type: Refine your search to only Thesis or Dissertation

Development of a Coaxiality Indicator

Description: The geometric dimensioning and tolerancing concept of coaxiality is often required by design engineers for balance of rotating parts and precision mating parts. In current practice, it is difficult for manufacturers to measure coaxiality quickly and inexpensively. This study examines feasibility of a manually-operated, mechanical device combined with formulae to indicate coaxiality of a test specimen. The author designs, fabricates, and tests the system for measuring coaxiality of holes machine… more
Access: Restricted to UNT Community Members. Login required if off-campus.
Date: December 1999
Creator: Arendsee, Wayne C.
Item Type: Refine your search to only Thesis or Dissertation

Development of a Hybrid Molecular Ultraviolet Photodetector based on Guanosine Derivatives

Description: Modern studies on charge transfer reaction and conductivity measurements of DNA have shown that the electrical behavior of DNA ranges from that of an insulator to that of a wide bandgap semiconductor. Based on this property of DNA, a metal-semiconductor-metal photodetector is fabricated using a self-assembled layer of deoxyguanosine derivative (DNA base) deposited between gold electrodes. The electrodes are lithographically designed on a GaN substrate separated by a distance L (50nm < L < 100nm… more
Access: Restricted to the UNT Community Members at a UNT Libraries Location.
Date: December 2005
Creator: Liddar, Harsheetal
Item Type: Refine your search to only Thesis or Dissertation
open access

Development of a Simplified Fracture Toughness Tool for Polymers

Description: This thesis presents research toward the development of a simple inexpensive fracture toughness tool for polymeric materials. Experiments were conducted to test the specimen configuration and the fracture toughness tool against an established ASTM standard for polymer fracture toughness, D5045, and a commonly used four-point bend method. The materials used in this study were polycarbonate and high density polyethylene. Reductions in both the production time and the variability resulting from th… more
Date: August 1997
Creator: Marnock, Patrick J. (Patrick Joseph)
Item Type: Refine your search to only Thesis or Dissertation
open access

Effect of Amines as Corrosion Inhibitors for a Low Carbon Steel in Power Industry

Description: Commonly used amines in power industry, including morpholine, DBU (1,8-diazabicyclo[5.4.0]undec-7-ene), and DMA (dimethylallylamine) were evaluated for their effect on AISI 1018 steel at 250oF. Samples were exposed to an autoclave containing amine added aqueous solution at pH of 9.5 for 1, 2, 4, 6, 8, and 12 hours. Morphology studies were carried using scanning electron microscope (SEM), phase analysis was done utilizing Fourier transform infrared spectroscopy (FTIR), and weight loss was perfor… more
Date: December 2004
Creator: Díaz, Jorge G.
Item Type: Refine your search to only Thesis or Dissertation

Effect of Engineered Surfaces on Valve Performance

Description: Performance of air operated valves is a major maintenance concern in process industries. Anecdotal information indicates that reliability of some high maintenance valves has been improved by using an ion deposition process to achieve engineered surfaces on selected components. This project compared friction for various surface treatments of selected valve components. Results indicate valve performance may be slightly more consistent when an engineered surface is applied in the valve packing are… more
Access: Restricted to UNT Community Members. Login required if off-campus.
Date: December 2000
Creator: Pope, Larry G.
Item Type: Refine your search to only Thesis or Dissertation
open access

Effects of a Surface Engineered Metallic Coating on Elastomeric Valve Stem Seal Leakage

Description: Valve stem seal leakage is a major source of fugitive emissions, and controlling these emissions can result in added expense in leak detection and repair programs. Elastomeric O-rings can be used as valve stem seals, and O-ring manufacturers recommend lubrication of elastomeric seals to prevent damage and to assure proper sealing. In this research, a metallic coating was applied as a lubricant using a vacuum vapor deposition process to the surface of elastomeric valve stem seals. Valve stem le… more
Date: December 2000
Creator: Taylor, John Abner
Item Type: Refine your search to only Thesis or Dissertation

Effects of Thickness and Indenter Tip Geometry in Nanoindentation of Nickel Films

Description: Nanoindentation has become a widely used technique to measure the mechanical properties of materials. Due to its capability to deform materials in micro- and nano-scale, nanoindentation has found more applications in characterizing the deformation behavior and determining the mechanical properties of thin films and coatings. This research deals with the characterization of samples received from Center for Advanced Microstructures and Devices (CAMD) and Integran Technologies Inc., Toronto, Canad… more
Access: Restricted to UNT Community Members. Login required if off-campus.
Date: May 2004
Creator: Parakala, Padma
Item Type: Refine your search to only Thesis or Dissertation

Evaluation of dynamic and static electrical characteristics for the DY8 and YI8 process gallium diodes in comparison to the DI8 process boron diodes.

Description: A rectifier is an electrical device, comprising one or more semiconductor devices arranged for converting alternating current to direct current by blocking the negative or positive portion of the waveform. The purpose of this study would be to evaluate dynamic and static electrical characteristics of rectifier chips fabricated with (a) DY8 process and (b) YI8 process and compare them with the existing DI8 process rectifiers. These new rectifiers were tested to compare their performance to meet … more
Access: Restricted to the UNT Community Members at a UNT Libraries Location.
Date: December 2006
Creator: Dhoopati, Swathi
Item Type: Refine your search to only Thesis or Dissertation
open access

Fabrication and Testing of Biomimetic Microstructures for Walkway Tribometers

Description: The main objective of this work is to give contribution in both additive manufacturing (AM) and tribometry derived from the application and study of materials available with the use of biomimetic designs. Additional contributions are determining what effects treatments for flooring surfaces may have on the dynamic coefficient of friction and the effects of these products on common surfaces. The validity of the proposed methodology for a proof of concept was demonstrated by comparing measured dy… more
Date: December 2019
Creator: Haney, Christopher Willard
Item Type: Refine your search to only Thesis or Dissertation
Back to Top of Screen