You limited your search to:

  Partner: UNT Libraries
 Department: Department of Engineering Technology
 Collection: UNT Theses and Dissertations
Knowledge Based System and Decision Making Methodologies in Materials Selection for Aircraft Cabin Metallic Structures

Knowledge Based System and Decision Making Methodologies in Materials Selection for Aircraft Cabin Metallic Structures

Date: August 2016
Creator: Adhikari, Pashupati Raj
Description: Materials selection processes have been the most important aspects in product design and development. Knowledge-based system (KBS) and some of the methodologies used in the materials selection for the design of aircraft cabin metallic structures are discussed. Overall aircraft weight reduction means substantially less fuel consumption. Part of the solution to this problem is to find a way to reduce overall weight of metallic structures inside the cabin. Among various methodologies of materials selection using Multi Criterion Decision Making (MCDM) techniques, a few of them are demonstrated with examples and the results are compared with those obtained using Ashby's approach in materials selection. Pre-defined constraint values, mainly mechanical properties, are employed as relevant attributes in the process. Aluminum alloys with high strength-to-weight ratio have been second-to-none in most of the aircraft parts manufacturing. Magnesium alloys that are much lighter in weight as alternatives to the Al-alloys currently in use in the structures are tested using the methodologies and ranked results are compared. Each material attribute considered in the design are categorized as benefit and non-benefit attribute. Using Ashby's approach, material indices that are required to be maximized for an optimum performance are determined, and materials are ranked based on the ...
Contributing Partner: UNT Libraries
Energy Harvesting Wireless Piezoelectric Resonant Force Sensor

Energy Harvesting Wireless Piezoelectric Resonant Force Sensor

Date: December 2013
Creator: Ahmadi, Mehdi
Description: The piezoelectric energy harvester has become a new powering option for some low-power electronic devices such as MEMS (Micro Electrical Mechanical System) sensors. Piezoelectric materials can collect the ambient vibrations energy and convert it to electrical energy. This thesis is intended to demonstrate the behavior of a piezoelectric energy harvester system at elevated temperature from room temperature up to 82°C, and compares the system’s performance using different piezoelectric materials. The systems are structured with a Lead Magnesium Niobate-Lead Titanate (PMN-PT) single crystal patch bonded to an aluminum cantilever beam, Lead Indium Niobate-Lead Magnesium Niobate-Lead Titanate (PIN-PMN-PT) single crystal patch bonded to an aluminum cantilever beam and a bimorph cantilever beam which is made of Lead Zirconate Titanate (PZT). The results of this experimental study show the effects of the temperature on the operation frequency and output power of the piezoelectric energy harvesting system. The harvested electrical energy has been stored in storage circuits including a battery. Then, the stored energy has been used to power up the other part of the system, a wireless resonator force sensor, which uses frequency conversion techniques to convert the sensor’s ultrasonic signal to a microwave signal in order to transmit the signal wirelessly.
Contributing Partner: UNT Libraries
A Computer-Based Process Control System for a Target Station in a LINAC Facility

A Computer-Based Process Control System for a Target Station in a LINAC Facility

Date: May 1999
Creator: Al-Shantaf, Abdulraouf O.
Description: An event-driven, sequential, process control system was designed for International Isotopes, Inc., to automate and remotely control a target station at the company's linear accelerator facility. The designed system consisted of two major sections: a software program (virtual instrument), which was developed by LabVIEW, and a hardware interface (FieldPoint Modular Distributed I/O System by National Instrument), which had to be a pre-developed system that did not require customization. The designed virtual instrument was tested on a simulation model that mimed the target station. The result was a valid design.
Contributing Partner: UNT Libraries
Development of a Coaxiality Indicator

Development of a Coaxiality Indicator

Access: Use of this item is restricted to the UNT Community.
Date: December 1999
Creator: Arendsee, Wayne C.
Description: The geometric dimensioning and tolerancing concept of coaxiality is often required by design engineers for balance of rotating parts and precision mating parts. In current practice, it is difficult for manufacturers to measure coaxiality quickly and inexpensively. This study examines feasibility of a manually-operated, mechanical device combined with formulae to indicate coaxiality of a test specimen. The author designs, fabricates, and tests the system for measuring coaxiality of holes machined in a steel test piece. Gage Repeatability and Reproducibility (gage R&R) and univariate analysis of variance is performed in accordance with Measurement System Analysis published by AIAG. Results indicate significant design flaws exist in the current configuration of the device; observed values vary greatly with operator technique. Suggestions for device improvements conclude the research.
Contributing Partner: UNT Libraries
A model for designing a new telecommunication system in Mongolia

A model for designing a new telecommunication system in Mongolia

Access: Use of this item is restricted to the UNT Community.
Date: May 2001
Creator: Baatarjav, Enkhbat
Description: The objective of this research is to design, and determine the feasibility of, a telecommunication system for the city of Erdenet, Mongolia. The Mongolian Telecommunication Company, Telecommunication Company of Erdenet city, and the National Statistical Office of Mongolia provided the data required for telecommunication forecasting of Erdenet. The literature review and analysis of the telecommunication forecasting indicate the need for a model of a new Telecommunication system in Erdenet, Mongolia. The model, as indicated, should become a useful example for planning and updating the telecommunication system in Mongolia. The design of a proposed telecommunication network involves the following considerations: analyzing and forecasting telephone traffic, calculating the required number of channels, determining exchange locations, traffic matrix, and establishing a basic hierarchical structure.
Contributing Partner: UNT Libraries
Development and Test of High-Temperature Piezoelectric Wafer Active Sensors for Structural Health Monitoring

Development and Test of High-Temperature Piezoelectric Wafer Active Sensors for Structural Health Monitoring

Date: December 2014
Creator: Bao, Yuanye
Description: High-temperature piezoelectric wafer active sensors (HT-PWAS) have been developed for structure health monitoring at hazard environments for decades. Different candidates have previously been tested under 270 °C and a new piezoelectric material langasite (LGS) was chosen here for a pilot study up to 700 °C. A preliminary study was performed to develop a high temperature sensor that utilizes langasite material. The Electromechanical impedance (E/M) method was chosen to detect the piezoelectric property. Experiments that verify the basic piezoelectric property of LGS at high temperature environments were carried out. Further validations were conducted by testing structures with attached LGS sensors at elevated temperature. Additionally, a detection system simulating the working process of LGS monitoring system was developed with PZT material at room temperature. This thesis, for the first time, (to the best of author’s knowledge) presents that langasite is ideal for making piezoelectric wafer active sensors for high temperature structure health monitoring applications.
Contributing Partner: UNT Libraries
Linearity and monotonicity of a 10-bit, 125 MHz, segmented current steering digital to analog converter

Linearity and monotonicity of a 10-bit, 125 MHz, segmented current steering digital to analog converter

Date: May 2000
Creator: Bittle, Charles C.
Description: The purpose of this research is to determine the linearity and monotonicity of the THS5651IDW digital to analog converter (DAC), a prototype of the future Texas Instruments TLV5651, 10-bit, 125 MHz communication DAC. Testing was conducted at the Texas Instruments facility on Forest Lane, Dallas, Texas. Texas Instruments provided test equipment, software and laboratory space to obtain test data. Analysis of the data found the DAC to be monotonic since the magnitude of the differential nonlinearity (DNL) was less than ± 1 least significant bit (LSB) and the integral nonlinearity (INL) was less than ± 0.5 LSB. The study also showed that the DAC has primarily negative DNL although the DNL is well within the desired specification.
Contributing Partner: UNT Libraries
Recommended Modified zone Method Correction Factor for Determining R-values of Cold-Formed Steel Wall Assemblies

Recommended Modified zone Method Correction Factor for Determining R-values of Cold-Formed Steel Wall Assemblies

Date: May 2011
Creator: Black, John
Description: Currently, ASHRAE has determined the zone method and modified zone method are appropriate calculation methods for materials with a high difference in conductivity, such as cold-formed steel (CFS) walls. Because there is currently no standard U-Factor calculation method for CFS walls, designers and code officials alike tend to resort to the zone method. However, the zone method is restricted to larger span assemblies because the zone factor coefficient is 2.0. This tends to overestimate the amount of surface area influenced by CFS. The modified zone method is restricted to C-shaped stud, clear wall assemblies with framing factors between 9 and 15%. The objective of the research is to narrow the gap of knowledge by re-examining the modified zone method in order to more accurately determine R-Values and U-Factors for CFS wall assemblies with whole wall framing factor percentages of 22% and above.
Contributing Partner: UNT Libraries
A Study of Laser Direct Writing for All Polymer Single Mode Passive Optical Channel Waveguide Devices

A Study of Laser Direct Writing for All Polymer Single Mode Passive Optical Channel Waveguide Devices

Date: May 2008
Creator: Borden, Bradley W.
Description: The objective of this research is to investigate the use of laser direct writing to micro-pattern low loss passive optical channel waveguide devices using a new hybrid organic/inorganic polymer. Review of literature shows previous methods of optical waveguide device patterning as well as application of other non-polymer materials. System setup and design of the waveguide components are discussed. Results show that laser direct writing of the hybrid polymer produce single mode interconnects with a loss of less 1dB/cm.
Contributing Partner: UNT Libraries
FPGA Prototyping of a Watermarking Algorithm for MPEG-4

FPGA Prototyping of a Watermarking Algorithm for MPEG-4

Date: May 2007
Creator: Cai, Wei
Description: In the immediate future, multimedia product distribution through the Internet will become main stream. However, it can also have the side effect of unauthorized duplication and distribution of multimedia products. That effect could be a critical challenge to the legal ownership of copyright and intellectual property. Many schemes have been proposed to address these issues; one is digital watermarking which is appropriate for image and video copyright protection. Videos distributed via the Internet must be processed by compression for low bit rate, due to bandwidth limitations. The most widely adapted video compression standard is MPEG-4. Discrete cosine transform (DCT) domain watermarking is a secure algorithm which could survive video compression procedures and, most importantly, attacks attempting to remove the watermark, with a visibly degraded video quality result after the watermark attacks. For a commercial broadcasting video system, real-time response is always required. For this reason, an FPGA hardware implementation is studied in this work. This thesis deals with video compression, watermarking algorithms and their hardware implementation with FPGAs. A prototyping VLSI architecture will implement video compression and watermarking algorithms with the FPGA. The prototype is evaluated with video and watermarking quality metrics. Finally, it is seen that the video qualities ...
Contributing Partner: UNT Libraries
Susceptibility of a digital turbine control system to IEEE 802.11 compliant emissions.

Susceptibility of a digital turbine control system to IEEE 802.11 compliant emissions.

Date: December 2003
Creator: Carter, Clinton E.
Description: Within the nuclear industry, there have been numerous instances of radio transmissions interfering with sensitive plant equipment. Instances documented vary from minor instrument fluctuations to major plant transients including reactor trips. With the nuclear power industry moving toward digital technologies for control and reactor protection systems, concern exists regarding their potential susceptibility to contemporary wireless telecommunications technologies. This study evaluates the susceptibility of Comanche Peak's planned turbine controls upgrade to IEEE 802.11 compliant wireless radio emissions. The study includes a review of previous research, industry emissions standards, and technical overview of the various IEEE 802.11 protocols and details the testing methodology utilized to evaluate the digital control system. The results of this study concluded that the subject digital control system was unaffected by IEEE 802.11 compliant emissions even when the transmitter was in direct contact with sensitive components.
Contributing Partner: UNT Libraries
Nominal Shear Strength and Seismic Detailing of Cold-formed Steel Shear Walls using Steel Sheet Sheathing

Nominal Shear Strength and Seismic Detailing of Cold-formed Steel Shear Walls using Steel Sheet Sheathing

Date: August 2010
Creator: Chen, Yujie
Description: In this research, monotonic and cyclic tests on cold-formed steel shear walls sheathed with steel sheets on one side were conducted to (1) verify the published nominal shear strength for 18-mil and 27-mil steel sheets; and (2) investigate the behavior of 6-ft. wide shear walls with multiple steel sheets. In objective 1: this research confirms the discrepancy existed in the published nominal strength of 27-mil sheets discovered by the previous project and verified the published nominal strength of 18 mil sheet for the wind design in AISI S213. The project also finds disagreement on the nominal strength of 18-mil sheets for seismic design, which is 29.0% higher than the published values. The research investigated 6-ft. wide shear wall with four framing and sheathing configurations. Configuration C, which used detailing, could provide the highest shear strength, compared to Configurations A and B. Meanwhile, the shear strength and stiffness of 2-ft. wide and 4-ft. wide wall can be improved by using the seismic detailing.
Contributing Partner: UNT Libraries
Ota-quadrotor: An Object-tracking Autonomous Quadrotor for Real-time Detection and Recognition

Ota-quadrotor: An Object-tracking Autonomous Quadrotor for Real-time Detection and Recognition

Date: May 2012
Creator: Coelho, Gavin
Description: The field of robotics and mechatronics is advancing at an ever-increasing rate and we are starting to see robots making the transition from the factories to the workplace and homes as cost is reduced and they become more useful. In recent years quadrotors have become a popular unmanned air vehicle (UAV) platform. These UAVs or micro air vehicles (MAV) are being used for many new and exciting applications such as aerial monitoring of wildlife, disaster sites, riots and protests. They are also being used in the film industry, as they are significantly cheaper means of getting aerial footage. While quadrotors are not extremely expensive a good system can cost in the range of $3000 - $8000 and thus too costly as a research platform for many. There are a number of cheaper open source platforms. The ArduCopter is under constant development, has the largest community and is inexpensive making it an ideal platform to work with. The goal of this thesis was to implement video processing on a ground control station allowing for the ArduCopter to track moving objects. This was achieved by using the OpenCV video-processing library to implement object tracking and the MAVLink communication protocol, available on the ...
Contributing Partner: UNT Libraries
Mist Characterization in Drilling 1018 Steel

Mist Characterization in Drilling 1018 Steel

Date: August 2012
Creator: Cole, Ian
Description: Minimum quantity lubrication replaces the traditional method of flood cooling with small amounts of high-efficient lubrication. Limited studies have been performed to determine the characteristics of mist produced during MQL. This study investigated the mist concentration levels produced while drilling 1018 steel using a vegetable based lubricant. ANOVA was performed to determine whether speed and feed rates or their interactions have a significant effect on mist concentration levels and particle diameter. It was observed that the concentration levels obtained under all four speed and feed rate combinations studied exceeded the current OSHA and NIOSH standards.
Contributing Partner: UNT Libraries
Cost Savings Realized Through Proper Sizing of an Excessive Instrument Air System.

Cost Savings Realized Through Proper Sizing of an Excessive Instrument Air System.

Date: December 2003
Creator: Condron, Ewell D.
Description: The purpose of this research was to determine if installing a smaller air compressor could reduce the electrical usage of a large semiconductor manufacturing plant. A 200 horsepower Atlas Copco compressor was installed with the existing 500 horsepower Ingersoll-Rand compressors. Testing was conducted during the regular manufacturing process at MEMC Southwest in Sherman, Texas. Analysis of the data found that installing the new compressor could reduce electrical consumption. The study also found there are specific operational setpoints that allow the compressor to operate more efficiently.
Contributing Partner: UNT Libraries
Evaluation of dynamic and static electrical characteristics for the DY8 and YI8 process gallium diodes in comparison to the DI8 process boron diodes.

Evaluation of dynamic and static electrical characteristics for the DY8 and YI8 process gallium diodes in comparison to the DI8 process boron diodes.

Access: Use of this item is restricted to the UNT Community.
Date: December 2006
Creator: Dhoopati, Swathi
Description: A rectifier is an electrical device, comprising one or more semiconductor devices arranged for converting alternating current to direct current by blocking the negative or positive portion of the waveform. The purpose of this study would be to evaluate dynamic and static electrical characteristics of rectifier chips fabricated with (a) DY8 process and (b) YI8 process and compare them with the existing DI8 process rectifiers. These new rectifiers were tested to compare their performance to meet or exceed requirements of lower forward voltages, leakage currents, reverse recovery time, and greater sustainability at higher temperatures compared to diodes manufactured using boron as base (DI8 process diodes) for similar input variables.
Contributing Partner: UNT Libraries
Using Motor Electrical Signature Analysis to Determine the Mechanical Condition of Vane-Axial Fans

Using Motor Electrical Signature Analysis to Determine the Mechanical Condition of Vane-Axial Fans

Date: August 2002
Creator: Doan, Donald Scott
Description: The purpose of this research was a proof of concept using a fan motor stator as transducer to monitor motor rotor and attached axial fan for mechanical motion. The proof was to determine whether bearing faults and fan imbalances could be detected in vane-axial fans using Motor Electrical Signature Analysis (MESA). The data was statistically analyzed to determine if the MESA systems could distinguish between baseline conditions and discrete fault frequencies for the three test conditions: bearing inner race defect, bearing outer race defect, and fan imbalance. The statistical conclusions for these proofs of concept were that MESA could identify all three faulted conditions.
Contributing Partner: UNT Libraries
Effects of Processing Techniques on Mechanical Properties of Selected Polymers

Effects of Processing Techniques on Mechanical Properties of Selected Polymers

Date: May 2013
Creator: Dong, Yao
Description: The mechanical properties of a polymer represent the critical characteristics to be considered when determining the applications for it. The same polymer processed with different methods can exhibit different mechanical properties. The purpose of this study is to investigate the difference in mechanical properties of the selected polymers caused by different processing techniques and conditions. Three polymers were studied, including low density polyethylene (LDPE), polypropylene (PP), and NEXPRENE® 1287A. Samples were processed with injection molding and compression molding under different processing condition. Tensile and DMA tests were performed on these samples. The acquired data of strain at break from the tensile tests and storage modulus from the DMA were utilized to calculate brittleness. Calculated brittleness values were used to perform analysis of variance (ANOVA) to investigate the statistical significance of the processing technique and condition. It was found that different processing techniques affect the brittleness significantly. The processing technique is the major factor affecting brittleness of PP and NEXPRENE, and the processing temperature is the major factor affecting brittleness of LDPE.
Contributing Partner: UNT Libraries
Increasing the Dynamic Range of Audio THD Measurements Using a Novel Noise and Distortion Canceling Methodology

Increasing the Dynamic Range of Audio THD Measurements Using a Novel Noise and Distortion Canceling Methodology

Access: Use of this item is restricted to the UNT Community.
Date: May 2003
Creator: Dunipace, Richard Alan
Description: The objective of this study was to determine how a new experimental methodology for measuring Total-Harmonic-Distortion (THD) of operational amplifiers functioned when compared with two standard methodologies, and whether the new methodology offers any improvement in noise floor and dynamic range along with distortion canceling of the sine-wave source used in the testing. The new methodology (THD) is being tested against two standard methodologies: Spectral Analysis using a tuned receiver type Spectrum Analyzer with Notch Filter pre-processing, and a digitized Fast Fourier Transform (FFT) using Notch Filter pre-processing. The THD results appear to agree across all methodologies, and across all items of the sample within all methodologies, to within a percent or less. The distortion and noise canceling feature of the new methodology appeared to function as expected and in accordance with theory. The sample tested in the study consisted of thirty-five NE5534 operational amplifiers produced by Texas Instruments, Inc. and purchased from a local store. The NE5534 is a low-noise, low-distortion, operational amplifier that is widely used in industry and is representative of today's best audio amplifiers.
Contributing Partner: UNT Libraries
Effect of Amines as Corrosion Inhibitors for a Low Carbon Steel in Power Industry

Effect of Amines as Corrosion Inhibitors for a Low Carbon Steel in Power Industry

Date: December 2004
Creator: Díaz, Jorge G.
Description: Commonly used amines in power industry, including morpholine, DBU (1,8-diazabicyclo[5.4.0]undec-7-ene), and DMA (dimethylallylamine) were evaluated for their effect on AISI 1018 steel at 250oF. Samples were exposed to an autoclave containing amine added aqueous solution at pH of 9.5 for 1, 2, 4, 6, 8, and 12 hours. Morphology studies were carried using scanning electron microscope (SEM), phase analysis was done utilizing Fourier transform infrared spectroscopy (FTIR), and weight loss was performed to assess kinetics of oxidation. Control samples showed the highest metal dissolution rate. DBU showed the best performance in metal protection and SEM indicated the presence of a free-crack layer formed by fine particles in that set. FTIR showed that DBU apparently favored the formation of magnetite. It is believed that fine particles impede intrusion of aggressive ions into the metal surface by forming a barrier layer. FTIR demonstrated that DMA formed more oxyhydroxides, whereas morpholine presented magnetite to hematite transformation as early as 2 hours. SEM revealed that control and DMA produced acicular particles characteristic of oxyhydroxides while morpholine and DBU presented more equiaxed particles.
Contributing Partner: UNT Libraries
Sunlight readability and luminance characteristics of light-emitting diode push button switches.

Sunlight readability and luminance characteristics of light-emitting diode push button switches.

Date: May 2004
Creator: Fitch, Robert J.
Description: Lighted push button switches and indicators serve many purposes in cockpits, shipboard applications and military ground vehicles. The quality of lighting produced by switches is vital to operators' understanding of the information displayed. Utilizing LED technology in lighted switches has challenges that can adversely affect lighting quality. Incomplete data exists to educate consumers about potential differences in LED switch performance between different manufacturers. LED switches from four different manufacturers were tested for six attributes of lighting quality: average luminance and power consumption at full voltage, sunlight readable contrast, luminance contrast under ambient sunlight, legend uniformity, and dual-color uniformity. Three of the four manufacturers have not developed LED push button switches that meet lighting quality standards established with incandescent technology.
Contributing Partner: UNT Libraries
Design of a Monitoring System for a Plasma Cleaning Machine

Design of a Monitoring System for a Plasma Cleaning Machine

Date: May 1999
Creator: Fooks, Terry M. (Terry Max)
Description: Plasma cleaning is the most effective dry process to remove surface contaminates from a SAW (Surface Acoustical Wave) device. Consistent gas pressures, flows, and good electrical connections between the chamber shelves are necessary for the process to function predictably. In addition, operation of the monitoring system must be transparent to the plasma cleaning unit. This thesis describes a simple solution to the complex problem of monitoring a plasma cleaning system. The monitoring system uses the LabVIEW® G programming language and hardware, both products of National Instruments, Inc.®, to monitor critical parameters necessary to achieve a consistent process when cleaning these devices.
Contributing Partner: UNT Libraries
Dynamic Behaviors of Historical Wrought Iron Truss Bridges – a Field Testing Case Study

Dynamic Behaviors of Historical Wrought Iron Truss Bridges – a Field Testing Case Study

Access: Use of this item is restricted to the UNT Community.
Date: December 2015
Creator: Hedric, Andrew C.
Description: Civil infrastructure throughout the world serves as main arteries for commerce and transportation, commonly forming the backbone of many societies. Bridges have been and remain a crucial part of the success of these civil networks. However, the crucial elements have been built over centuries and have been subject to generations of use. Many current bridges have outlived their intended service life or have been retrofitted to carry additional loads over their original design. A large number of these historic bridges are still in everyday use and their condition needs to be monitored for public safety. Transportation infrastructure authorities have implemented various inspection and management programs throughout the world, mainly visual inspections. However, careful visual inspections can provide valuable information but it has limitations in that it provides no actual stress-strain information to determine structural soundness. Structural Health Monitoring (SHM) has been a growing area of research as officials need to asses and triage the aging infrastructure with methods that provide measurable response information to determine the health of the structure. A rapid improvement in technology has allowed researchers to start using new sensors and algorithms to understand the structural parameters of tested structures due to known and unknown loading scenarios. ...
Contributing Partner: UNT Libraries
The Use of Optical Metrology in Active Positioning of a Lens

The Use of Optical Metrology in Active Positioning of a Lens

Date: August 2014
Creator: Ji, Zheng
Description: Precisely positioned optical lenses are currently required for many highly repetitive mechanics and applications. Thus the need for micron-scale repetition between opto-mechanical units is evident, especially in industrial manufacturing and medical breakthroughs. In this thesis, a novel optical metrology system is proposed, designed, and built whose purpose is to precisely locate the center of a mechanical fixture and then to assemble a plano-convex optical lens into the located position of the fixture. Center location specifications up to ±3 µm decenter and ±0.001° tilting accuracy are required. Nine precisely positioned lenses and fixtures were built with eight units passing the requirements with a repetitive standard deviation of ±0.15 µm or less. The assembled units show satisfactory results.
Contributing Partner: UNT Libraries
FIRST PREV 1 2 3 4 NEXT LAST