UNT Theses and Dissertations - 103 Matching Results

Search Results

prev Results: 41 - 64 next

Cold-Formed Steel Member Connections Using BAC Screw Fasteners

Description: In this project, the main research objective is intend to seek criteria for evaluating the capacity of BAC screw fasteners with mixed configuration of waterproof seal washer, sealer tape and different pre-drill holes to determine shear and tension strength values for the screws used in cold-formed steel connections. The thesis presents the design methods and test program conducted to investigate the behavior and strength of the screw connections in shear and tension test. Test results were comp… more
Access: Restricted to UNT Community Members. Login required if off-campus.
Date: May 2019
Creator: Li, Xun
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Development of a Hybrid Molecular Ultraviolet Photodetector based on Guanosine Derivatives

Description: Modern studies on charge transfer reaction and conductivity measurements of DNA have shown that the electrical behavior of DNA ranges from that of an insulator to that of a wide bandgap semiconductor. Based on this property of DNA, a metal-semiconductor-metal photodetector is fabricated using a self-assembled layer of deoxyguanosine derivative (DNA base) deposited between gold electrodes. The electrodes are lithographically designed on a GaN substrate separated by a distance L (50nm < L < 100nm… more
Access: Restricted to the UNT Community Members at a UNT Libraries Location.
Date: December 2005
Creator: Liddar, Harsheetal
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

A Data Acquisition System Experiment for Gas Temperature and Pressure Measurements on a Liquid-Nitrogen-Powered Vehicle

Description: A data acquisition system was set up to measure gas temperatures and pressures at various points on a liquid-nitrogen-powered vehicle. The experiment was attempted to develop a data acquisition method for applications on engines that use liquid air as the fuel. Two thermocouples and a pressure transducer were connected using data acquisition instruments interfaced to a laptop computer to acquire data.
Date: May 1998
Creator: Lui, Samson Sze-Sang
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Innovative Cold-Formed Steel Shear Walls with Corrugated Steel Sheathing

Description: This thesis presents two major sections with the objective of introducing a new cold-formed steel (CFS) shear wall system with corrugated steel sheathings. The work shown herein includes the development of an optimal shear wall system as well as an optimal slit configuration for the CFS corrugated sheathings which result in a CFS shear wall with high ductility, high strength, high stiffness and overall high performance. The conclusion is based on the results of 36 full-scale shear wall tests pe… more
Date: May 2016
Creator: Mahdavian, Mahsa
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Characterization of Boron Nitride Thin Films on Silicon (100) Wafer.

Description: Cubic boron nitride (cBN) thin films offer attractive mechanical and electrical properties. The synthesis of cBN films have been deposited using both physical and chemical vapor deposition methods, which generate internal residual, stresses that result in delamination of the film from substrates. Boron nitride films were deposited using electron beam evaporation without bias voltage and nitrogen bombardment (to reduce stresses) were characterize using FTIR, XRD, SEM, EDS, TEM, and AFM technique… more
Date: August 2007
Creator: Maranon, Walter
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Investigation of the feasibility of non-invasive carbon dioxide detection using spectroscopy in the visible spectrum.

Description: Pulse oximeters are used in operating rooms and recovery rooms as a monitoring device for oxygen in the respiratory system of the patient. The advantage of pulse oximeters over other methods of oxygen monitoring is that they are easy to use and they are non-invasive, which means it is not necessary break the skin to extract blood for information to be obtained. The standard for the measurement of partial pressure of CO2 and O2 is an arterial blood gas analysis (ABG). However routine monitoring … more
Date: December 2007
Creator: Marks, Damian
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Development of a Simplified Fracture Toughness Tool for Polymers

Description: This thesis presents research toward the development of a simple inexpensive fracture toughness tool for polymeric materials. Experiments were conducted to test the specimen configuration and the fracture toughness tool against an established ASTM standard for polymer fracture toughness, D5045, and a commonly used four-point bend method. The materials used in this study were polycarbonate and high density polyethylene. Reductions in both the production time and the variability resulting from th… more
Date: August 1997
Creator: Marnock, Patrick J. (Patrick Joseph)
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Effects of Minimum Quantity Lubrication (Mql) on Tool Life in Drilling Aisi 1018 Steel

Description: It has been reported that minimum quantity lubrication (MQL) provides better tool life compared to flood cooling under some drilling conditions. In this study, I evaluate the performance of uncoated HSS twist drill when machining AISI 1018 steel using a newly developed lubricant designed for MQL (EQO-Kut 718 by QualiChem Inc.). A randomized factorial design was used in the experiment. The results show that a tool life of 1110 holes with a corresponding flank wear of 0.058 mm was realized.
Date: August 2012
Creator: Maru, Tejas
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Hardware and Software Codesign of a JPEG2000 Watermarking Encoder

Description: Analog technology has been around for a long time. The use of analog technology is necessary since we live in an analog world. However, the transmission and storage of analog technology is more complicated and in many cases less efficient than digital technology. Digital technology, on the other hand, provides fast means to be transmitted and stored. Digital technology continues to grow and it is more widely used than ever before. However, with the advent of new technology that can reproduce d… more
Date: December 2008
Creator: Mendoza, Jose Antonio
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Investigation of Immersion Cooled ARM-Based Computer Clusters for Low-Cost, High-Performance Computing

Description: This study aimed to investigate performance of ARM-based computer clusters using two-phase immersion cooling approach, and demonstrate its potential benefits over the air-based natural and forced convection approaches. ARM-based clusters were created using Raspberry Pi model 2 and 3, a commodity-level, single-board computer. Immersion cooling mode utilized two types of dielectric liquids, HFE-7000 and HFE-7100. Experiments involved running benchmarking tests Sysbench high performance linpack (H… more
Date: August 2017
Creator: Mohammed, Awaizulla Shareef
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Laser Cutting Machine: Justification of initial costs

Description: The Industrial Laser is firmly established in metalcutting as the tool of choice for many applications. The elevator division of Montgomery KONE Inc., in an effort to move towards quality, ontime, complete deliveries and 100% customer satisfaction, decided to invest in new equipment to improve manufacturing processes. A huge investment is proposed for a laser-cutting machine. It is the responsibility of Manufacturing Engineering to direct the management by justifying its benefits, which include… more
Date: May 2001
Creator: Nagaraja, Dwarakish
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Design of Power Amplifier Test Signals with a User-Defined Multisine

Description: Cellular radio communication involves wireless transmission and reception of signals at radio frequencies (RF). Base stations house equipment critical to the transmission and reception of signals. Power amplifier (PA) is a crucial element in base station assembly. PAs are expensive, take up space and dissipate heat. Of all the elements in the base station, it is difficult to design and operate a power amplifier. New designs of power amplifiers are constantly tested. One of the most important co… more
Access: Restricted to UNT Community Members. Login required if off-campus.
Date: May 2004
Creator: Nagarajan, Preeti
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Flow Accelerated Corrosion Experience at Comanche Peak Steam Electric Station

Description: Flow accelerated corrosion (FAC) is a major concern in the power industry as it causes thinning of the pipes by the dissolution of the passive oxide layer formed on the pipe surface. Present research deals with comparing the protection offered by the magnetite (Fe3O4) versus maghemite (γ-Fe2O3) phases thickness loss measurements. Fourier transform infrared spectroscopy (FTIR) is used in distinguishing these two elusive phases of iron oxides. Representative pipes are collected from high pressure… more
Date: May 2008
Creator: Nakka, Ravi Kumar
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Characterization of Iron Oxide Deposits Formed at Comanche Peak Steam Electric Station

Description: The presence of deposits leading to corrosion of the steam generator (SG) systems is a major contributor to operation and maintenance cost of pressurized water reactor (PWR) plants. Formation and transport of corrosion products formed due to the presence of impurities, metallic oxides and cations in the secondary side of the SG units result in formation of deposits. This research deals with the characterization of deposit samples collected from the two SG units (unit 1 and unit 2) at Comanche P… more
Access: Restricted to the UNT Community Members at a UNT Libraries Location.
Date: May 2003
Creator: Namduri, Haritha
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Liquid Nitrogen Propulsion Systems for Automotive Applications: Calculation of Mechanical Efficiency of a Dual, Double-acting Piston Propulsion System

Description: A dual, double-acting propulsion system is analyzed to determine how efficiently it can convert the potential energy available from liquid nitrogen into useful work. The two double-acting pistons (high- and low-pressure) were analyzed by using a Matlab-Simulink computer simulation to determine their respective mechanical efficiencies. The flow circuit for the entire system was analyzed by using flow circuit analysis software to determine pressure losses throughout the system at the required mas… more
Date: May 2008
Creator: North, Thomas B.
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Two-Phase Spray Cooling with Water/2-Propanol Binary Mixtures for High Heat Flux Focal Source

Description: Two-phase spray cooling has been an emerging thermal management technique offering high heat transfer coefficients and critical heat flux levels, near-uniform surface temperatures, and efficient coolant usage that enables to design of compact and lightweight systems. Due to these capabilities, spray cooling is a promising approach for high heat flux applications in computing, power electronics, and optics. Two-phase spray cooling inherently depends on saturation temperature-pressure relations… more
Date: December 2016
Creator: Obuladinne, Sai Sujith
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Mechanical Characterization of A2 and D2 Tool Steels By Nanoindentation

Description: Nanoindentation technique was used to investigate the surface properties of A2 and D2 tool steel subjected to different heat treatments. the mechanical characteristics of these two easily available tool steels were studied based on microstructural images obtained from SEM, the grain growth after heat treatment using X-ray diffraction method and nanoindentation technique. the investigation showed that a single nanoindentation result can explain how heat treatment influences reliability and failu… more
Date: May 2012
Creator: Okafor, Uzochukwu Chimezie
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Bearing Strength of Cold Formed Steel Bolted Connections in Trusses

Description: The existing design provision in North American Specification for Cold- Formed Steel Structural Member (AISI S100) for the bearing strength of bolted connections were developed from tests on bolted connected sheets which were restrained by bolt nut and head with or without washers. However, in the cold-formed assemblies, particularly in trusses, the single bolt goes through both sides of the connected sections, making the connected sheets on each side unrestrained. the warping of the unrestrain… more
Date: May 2012
Creator: Panyanouvong, Mark
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Effects of Thickness and Indenter Tip Geometry in Nanoindentation of Nickel Films

Description: Nanoindentation has become a widely used technique to measure the mechanical properties of materials. Due to its capability to deform materials in micro- and nano-scale, nanoindentation has found more applications in characterizing the deformation behavior and determining the mechanical properties of thin films and coatings. This research deals with the characterization of samples received from Center for Advanced Microstructures and Devices (CAMD) and Integran Technologies Inc., Toronto, Canad… more
Access: Restricted to UNT Community Members. Login required if off-campus.
Date: May 2004
Creator: Parakala, Padma
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Effects of Rebar Temperature and Water to Cement Ratio on Rebar-Concrete Bond Strength of Concrete Containing Fly Ash

Description: This research presents the results on an experimental investigation to identify the effects of rebar temperature, fly ash and water to cement ratio on concrete porosity in continuously reinforced concrete pavements (CRCP). Samples were cast and analyzed using pullout tests. Water to cement ratio (w/c) and rebar temperature had a significant influence on the rebar-concrete bond strength. The 28-day shear strength measurements showed an increase in rebar-concrete bond strength as the water to cem… more
Date: May 2010
Creator: Pati, Ardeep Ranjan
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Topology and Lattice-Based Structural Design Optimization for Additively Manufactured Medical Implants

Description: Topology-based optimization techniques and lattice structures are powerful ways to accomplish lightweight components with enhanced mechanical performance. Recent developments in additive manufacturing (AM) have led the way to extraordinary opportunities in realizing complex designs that are derived from topology and lattice-based structural optimization. The main aim of this work is to give a contribution, in the integration between structural optimization techniques and AM, by proposing a setu… more
Date: May 2019
Creator: Peto, Marinela
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Corrosion Protection of Low Carbon Steel By Cation Substituted Magnetite

Description: Surfaces of low carbon steel sheet were modified by exposure to highly caustic aqueous solutions containing either chromium or aluminum cations. Corrosion resistances of such surfaces were compared with that of steel surfaces exposed to plain caustic aqueous solution. In all cases a highly uniform, black coating having a spinel structure similar to magnetite (Fe3O4) was obtained. The coated steel surfaces were characterized using X-ray photoelectron spectroscopy (XPS), scanning electron micros… more
Date: May 2013
Creator: Phadnis, Ameya
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Design, Modeling, and Experiment of a Piezoelectric Pressure Sensor based on a Thickness-Shear Mode Crystal Resonator

Description: This thesis presents the design, modeling, and experiment of a novel pressure sensor using a dual-mode AT-cut quartz crystal resonator with beat frequency analysis based temperature compensation technique. The proposed sensor can measure pressure and temperature simultaneously by a single AT-cut quartz resonator. Apart from AT-cut quartz crystal, a newly developed Langasite (LGS) crystal resonator is also considered in the proposed pressure sensor design, since LGS can operate in a higher tempe… more
Date: May 2017
Creator: Pham, Thanh Tuong
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Design and Validation of an Automated Multiunit Composting System.

Description: This thesis covers the design of an automated multiunit composting system (AMUCS) that was constructed to meet the experimental apparatus requirements of the ASTM D5338 standard. The design of the AMUCS is discussed in full detail and validated with two experiments. The first experiment was used to validate the operation of the AMUCS with a 15 day experiment. During this experiment visual observations were made to visually observe degradation. Thermal properties and stability tests were perform… more
Date: December 2009
Creator: Pickens, Mark Everett
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
Back to Top of Screen