UNT Theses and Dissertations - 52 Matching Results

Search Results

Results: 1 - 24 next
open access

Effects of Rebar Temperature and Water to Cement Ratio on Rebar-Concrete Bond Strength of Concrete Containing Fly Ash

Description: This research presents the results on an experimental investigation to identify the effects of rebar temperature, fly ash and water to cement ratio on concrete porosity in continuously reinforced concrete pavements (CRCP). Samples were cast and analyzed using pullout tests. Water to cement ratio (w/c) and rebar temperature had a significant influence on the rebar-concrete bond strength. The 28-day shear strength measurements showed an increase in rebar-concrete bond strength as the water to cem… more
Date: May 2010
Creator: Pati, Ardeep Ranjan
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Cold-Formed Steel Bolted Connections Using Oversized and Slotted Holes without Washers

Description: In cold-formed steel (CFS) construction, bolted connections without washers for either oversized or slotted holes may significantly expedite the installation process and lower the cost. However, the North American Specification (AISI S100, 2007) for the Design of Cold-Formed Steel Structural Members requires washers to be installed in bolted connections with oversized or slotted holes. A research project (Phase 1) sponsored by American Iron and Steel Institute (AISI) was recently completed at t… more
Date: August 2010
Creator: Xu, Ke
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Nominal Shear Strength and Seismic Detailing of Cold-formed Steel Shear Walls using Steel Sheet Sheathing

Description: In this research, monotonic and cyclic tests on cold-formed steel shear walls sheathed with steel sheets on one side were conducted to (1) verify the published nominal shear strength for 18-mil and 27-mil steel sheets; and (2) investigate the behavior of 6-ft. wide shear walls with multiple steel sheets. In objective 1: this research confirms the discrepancy existed in the published nominal strength of 27-mil sheets discovered by the previous project and verified the published nominal strength … more
Date: August 2010
Creator: Chen, Yujie
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Effect of Polyphosphoric Acid on Aging Characteristics of PG 64-22 Asphalt Binder

Description: This research presents the results on an experimental investigation to identify the effect of polyphosphoric acid (PPA) on aging characteristics of an asphalt binder. Addition of PPA to asphalt binders is said to improve performance of flexible pavements. Asphalt binder PG 64-22 in modified and unmodified conditions was subjected to aging in the laboratory using a regular oven and also simulated short term aging using rolling thin film oven (RTFO) test. Aging experiments were conducted to analy… more
Date: December 2010
Creator: Ramasamy, Naresh Baboo
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Software and Hardware-In-The-Loop Modeling of an Audio Watermarking Algorithm

Description: Due to the accelerated growth in digital music distribution, it becomes easy to modify, intercept, and distribute material illegally. To overcome the urgent need for copyright protection against piracy, several audio watermarking schemes have been proposed and implemented. These digital audio watermarking schemes have the purpose of embedding inaudible information within the host file to cover copyright and authentication issues. This thesis proposes an audio watermarking model using MATLAB® an… more
Date: December 2010
Creator: Zarate Orozco, Ismael
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Recommended Modified zone Method Correction Factor for Determining R-values of Cold-Formed Steel Wall Assemblies

Description: Currently, ASHRAE has determined the zone method and modified zone method are appropriate calculation methods for materials with a high difference in conductivity, such as cold-formed steel (CFS) walls. Because there is currently no standard U-Factor calculation method for CFS walls, designers and code officials alike tend to resort to the zone method. However, the zone method is restricted to larger span assemblies because the zone factor coefficient is 2.0. This tends to overestimate the amou… more
Date: May 2011
Creator: Black, John
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Bearing Strength of Cold Formed Steel Bolted Connections in Trusses

Description: The existing design provision in North American Specification for Cold- Formed Steel Structural Member (AISI S100) for the bearing strength of bolted connections were developed from tests on bolted connected sheets which were restrained by bolt nut and head with or without washers. However, in the cold-formed assemblies, particularly in trusses, the single bolt goes through both sides of the connected sections, making the connected sheets on each side unrestrained. the warping of the unrestrain… more
Date: May 2012
Creator: Panyanouvong, Mark
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Mechanical Characterization of A2 and D2 Tool Steels By Nanoindentation

Description: Nanoindentation technique was used to investigate the surface properties of A2 and D2 tool steel subjected to different heat treatments. the mechanical characteristics of these two easily available tool steels were studied based on microstructural images obtained from SEM, the grain growth after heat treatment using X-ray diffraction method and nanoindentation technique. the investigation showed that a single nanoindentation result can explain how heat treatment influences reliability and failu… more
Date: May 2012
Creator: Okafor, Uzochukwu Chimezie
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Nominal Shear Strength of Cold-formed Steel Shear Walls Using Osb Sheathing

Description: In the cold-formed steel construction, the oriented strand board is a common material for shear wall sheathing. an OSB is made by using wood chips as raw materials that undergo high temperature pressing to create a multi-larger structure material. Due to the OSB having a high strength in shear, it is an important material used in the construction field. the thesis is trying to verify published nominal shear strength in AISI-213-07 in the first part. This objective has two parts: the first part … more
Date: May 2012
Creator: Li, Chao
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Ota-quadrotor: An Object-tracking Autonomous Quadrotor for Real-time Detection and Recognition

Description: The field of robotics and mechatronics is advancing at an ever-increasing rate and we are starting to see robots making the transition from the factories to the workplace and homes as cost is reduced and they become more useful. In recent years quadrotors have become a popular unmanned air vehicle (UAV) platform. These UAVs or micro air vehicles (MAV) are being used for many new and exciting applications such as aerial monitoring of wildlife, disaster sites, riots and protests. They are also be… more
Date: May 2012
Creator: Coelho, Gavin
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Drive Level Dependence of Advanced Piezoelectric Resonators

Description: Resonators are one of the most important parts of electronic products. They provide a stable reference frequency to ensure the operation of these products. Recently, the electronic products have the trend of miniaturization, which rendered the size reduction of the resonators as well [1]. Better design of the resonators relies on a better understanding of the crystals' nonlinear behavior [2]. The nonlinearities affect the quality factor and acoustic behavior of MEMS (Micro-Electro-Mechanical-Sy… more
Date: August 2012
Creator: Xie, Yuan
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Effects of Minimum Quantity Lubrication (Mql) on Tool Life in Drilling Aisi 1018 Steel

Description: It has been reported that minimum quantity lubrication (MQL) provides better tool life compared to flood cooling under some drilling conditions. In this study, I evaluate the performance of uncoated HSS twist drill when machining AISI 1018 steel using a newly developed lubricant designed for MQL (EQO-Kut 718 by QualiChem Inc.). A randomized factorial design was used in the experiment. The results show that a tool life of 1110 holes with a corresponding flank wear of 0.058 mm was realized.
Date: August 2012
Creator: Maru, Tejas
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Mist Characterization in Drilling 1018 Steel

Description: Minimum quantity lubrication replaces the traditional method of flood cooling with small amounts of high-efficient lubrication. Limited studies have been performed to determine the characteristics of mist produced during MQL. This study investigated the mist concentration levels produced while drilling 1018 steel using a vegetable based lubricant. ANOVA was performed to determine whether speed and feed rates or their interactions have a significant effect on mist concentration levels and partic… more
Date: August 2012
Creator: Cole, Ian
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Wireless In-home Ecg Monitoring System with Remote Access

Description: The thesis work details the design and testing of a wireless electrocardiogram (ECG) system. This system includes a wireless ECG device, as well as software packages to visually display the waveform locally on a computer and remotely on a web page. The remote viewing capability also extends to using an Android phone application. The purpose of the system is to serve as a means for a doctor or physician to check up on a patient away from a hospital setting. This system allows for a patient to be… more
Date: August 2012
Creator: Porter, Logan
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Analytical Model of Cold-formed Steel Framed Shear Wall with Steel Sheet and Wood-based Sheathing

Description: The cold-formed steel framed shear walls with steel sheets and wood-based sheathing are both code approved lateral force resisting system in light-framed construction. In the United States, the current design approach for cold-formed steel shear walls is capacity-based and developed from full-scale tests. The available design provisions provide nominal shear strength for only limited wall configurations. This research focused on the development of analytical models of cold-formed steel framed s… more
Date: May 2013
Creator: Yanagi, Noritsugu
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Cold-formed Steel Framed Shear Wall Sheathed with Corrugated Sheet Steel

Description: Incombustibility is one important advantage of the sheet steel sheathed shear wall over wood panel sheathed shear wall. Compared to shear wall sheathed with plywood and OSB panel, shear wall sheathed with flat sheet steel behaved lower shear strength. Although shear wall sheathed with corrugated sheet steel exhibited high nominal strength and high stiffness, the shear wall usually behaved lower ductility resulting from brittle failure at the connection between the sheathing to frames. This rese… more
Date: May 2013
Creator: Yu, Guowang
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Corrosion Protection of Low Carbon Steel By Cation Substituted Magnetite

Description: Surfaces of low carbon steel sheet were modified by exposure to highly caustic aqueous solutions containing either chromium or aluminum cations. Corrosion resistances of such surfaces were compared with that of steel surfaces exposed to plain caustic aqueous solution. In all cases a highly uniform, black coating having a spinel structure similar to magnetite (Fe3O4) was obtained. The coated steel surfaces were characterized using X-ray photoelectron spectroscopy (XPS), scanning electron micros… more
Date: May 2013
Creator: Phadnis, Ameya
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Direct Strength Method for Web Crippling of Cold-formed Steel C-sections

Description: Web crippling is a form of localized buckling that occurs at points of transverse concentrated loading or supports of thin-walled structural members. The theoretical computation of web crippling strength is quite complex as it involves a large number of factors such as initial imperfections, local yielding at load application and instability of web. The existing design provision in North American specification for cold-formed steel C-sections (AISI S100, 2007) to calculate the web-crippling str… more
Date: May 2013
Creator: Seelam, Praveen Kumar Reddy
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Effects of Processing Techniques on Mechanical Properties of Selected Polymers

Description: The mechanical properties of a polymer represent the critical characteristics to be considered when determining the applications for it. The same polymer processed with different methods can exhibit different mechanical properties. The purpose of this study is to investigate the difference in mechanical properties of the selected polymers caused by different processing techniques and conditions. Three polymers were studied, including low density polyethylene (LDPE), polypropylene (PP), and NEXP… more
Date: May 2013
Creator: Dong, Yao
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Energy Harvesting Wireless Piezoelectric Resonant Force Sensor

Description: The piezoelectric energy harvester has become a new powering option for some low-power electronic devices such as MEMS (Micro Electrical Mechanical System) sensors. Piezoelectric materials can collect the ambient vibrations energy and convert it to electrical energy. This thesis is intended to demonstrate the behavior of a piezoelectric energy harvester system at elevated temperature from room temperature up to 82°C, and compares the system’s performance using different piezoelectric materials.… more
Date: December 2013
Creator: Ahmadi, Mehdi
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

The Measurement of the Third-order Elastic Constants for La3ga5sio14 (Lgs) and La3ga55ta05o14 (Lgt) Single Crystal

Description: Recently, the development of electronic technology towards higher frequencies and larger band widths has led to interest in finding new piezoelectric materials, which could be used to make filters with larger pass band widths and oscillators with better frequency stability. Langasite (La3Ga5SiO14, LGS) and its isomorphs have enticed considerable attention of researchers as a potential substrate material for piezoelectric device applications because of its high frequency stability and fairly goo… more
Date: December 2013
Creator: Karim, Md Afzalul
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Control and Automation of a Heat Shrink Tubing Process

Description: Heat shrink tubing is used to insulate wire conductors, protect wires, and to create cable entry seals in wire harnessing industries. Performing this sensitive process manually is time consuming, the results are strongly dependent on the operator’s expertise, and the process presents safety concerns. Alternatively, automating the process minimizes the operators’ direct interaction, decreases the production cost over the long term, and improves quantitative and qualitative production indicators … more
Date: August 2014
Creator: Yousefi Darani, Shahrokh
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

The Use of Optical Metrology in Active Positioning of a Lens

Description: Precisely positioned optical lenses are currently required for many highly repetitive mechanics and applications. Thus the need for micron-scale repetition between opto-mechanical units is evident, especially in industrial manufacturing and medical breakthroughs. In this thesis, a novel optical metrology system is proposed, designed, and built whose purpose is to precisely locate the center of a mechanical fixture and then to assemble a plano-convex optical lens into the located position of the… more
Date: August 2014
Creator: Ji, Zheng
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Analytical Model for Lateral Deflection in Cold-formed Steel Framed Shear Walls with Steel Sheathing

Description: An analytical model for lateral deflection in cold-formed steel shear walls sheathed with steel is developed in this research. The model is based on the four factors: fastener displacement, steel sheet deformation, and hold-down deformation, which are from the effective strip concept and a complexity factor, which accounts for the additional influential factors not considered in the previous three terms. The model uses design equations based on the actual material and mechanical properties of t… more
Date: December 2014
Creator: Yousof, Mohamad
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
Back to Top of Screen