UNT Theses and Dissertations - 52 Matching Results

Search Results

Results: 1 - 24 next
open access

Accelerated Corrosion Test with Operation Simulation of All-Aluminum Microchannel Heat Exchangers

Description: The HVAC&R industry is looking to transition from copper-aluminum heat exchangers to all-aluminum microchannel technology. The want for the transition stemmed from seeing the performance improvement of all-aluminum microchannel radiators in the automotive industry. Applications differ between the two industries; therefore, applying this technology for HVAC&R use must be validated. Research towards operating modes of an all-aluminum heat exchanger in a defined corrosive environment will provide … more
Date: May 2016
Creator: Vaughan, Haydn
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Analytical Model for Lateral Deflection in Cold-formed Steel Framed Shear Walls with Steel Sheathing

Description: An analytical model for lateral deflection in cold-formed steel shear walls sheathed with steel is developed in this research. The model is based on the four factors: fastener displacement, steel sheet deformation, and hold-down deformation, which are from the effective strip concept and a complexity factor, which accounts for the additional influential factors not considered in the previous three terms. The model uses design equations based on the actual material and mechanical properties of t… more
Date: December 2014
Creator: Yousof, Mohamad
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Analytical Model of Cold-formed Steel Framed Shear Wall with Steel Sheet and Wood-based Sheathing

Description: The cold-formed steel framed shear walls with steel sheets and wood-based sheathing are both code approved lateral force resisting system in light-framed construction. In the United States, the current design approach for cold-formed steel shear walls is capacity-based and developed from full-scale tests. The available design provisions provide nominal shear strength for only limited wall configurations. This research focused on the development of analytical models of cold-formed steel framed s… more
Date: May 2013
Creator: Yanagi, Noritsugu
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Bearing Strength of Cold Formed Steel Bolted Connections in Trusses

Description: The existing design provision in North American Specification for Cold- Formed Steel Structural Member (AISI S100) for the bearing strength of bolted connections were developed from tests on bolted connected sheets which were restrained by bolt nut and head with or without washers. However, in the cold-formed assemblies, particularly in trusses, the single bolt goes through both sides of the connected sections, making the connected sheets on each side unrestrained. the warping of the unrestrain… more
Date: May 2012
Creator: Panyanouvong, Mark
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Cold-Formed Steel Bolted Connections Using Oversized and Slotted Holes without Washers

Description: In cold-formed steel (CFS) construction, bolted connections without washers for either oversized or slotted holes may significantly expedite the installation process and lower the cost. However, the North American Specification (AISI S100, 2007) for the Design of Cold-Formed Steel Structural Members requires washers to be installed in bolted connections with oversized or slotted holes. A research project (Phase 1) sponsored by American Iron and Steel Institute (AISI) was recently completed at t… more
Date: August 2010
Creator: Xu, Ke
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Cold-formed Steel Framed Shear Wall Sheathed with Corrugated Sheet Steel

Description: Incombustibility is one important advantage of the sheet steel sheathed shear wall over wood panel sheathed shear wall. Compared to shear wall sheathed with plywood and OSB panel, shear wall sheathed with flat sheet steel behaved lower shear strength. Although shear wall sheathed with corrugated sheet steel exhibited high nominal strength and high stiffness, the shear wall usually behaved lower ductility resulting from brittle failure at the connection between the sheathing to frames. This rese… more
Date: May 2013
Creator: Yu, Guowang
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Cold-Formed Steel Member Connections Using BAC Screw Fasteners

Description: In this project, the main research objective is intend to seek criteria for evaluating the capacity of BAC screw fasteners with mixed configuration of waterproof seal washer, sealer tape and different pre-drill holes to determine shear and tension strength values for the screws used in cold-formed steel connections. The thesis presents the design methods and test program conducted to investigate the behavior and strength of the screw connections in shear and tension test. Test results were comp… more
Access: Restricted to UNT Community Members. Login required if off-campus.
Date: May 2019
Creator: Li, Xun
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Comparative Analysis and Implementation of High Data Rate Wireless Sensor Network Simulation Frameworks

Description: This thesis focuses on developing a high data rate wireless sensor network framework that could be integrated with hardware prototypes to monitor structural health of buildings. In order to better understand the wireless sensor network architecture and its consideration in structural health monitoring, a detailed literature review on wireless sensor networks has been carried out. Through research, it was found that there are numerous simulation software packages available for wireless sensor ne… more
Date: December 2015
Creator: Laguduva Rajaram, Madhupreetha
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Construction Management Methods and Techniques in Army Tactical Shelter

Description: This thesis presents a research effort aimed at developing using construction methods and techniques in army tactical shelter. The beginning step focuses on developing and identifying different activities and work breakdown structure applicable in shelter prototype. The next step focuses on identifying resource allocation. This include allocate resources based on the delivered project as per alternative one and for the second alternative as optimization, resource allocation modified and tried t… more
Access: Restricted to UNT Community Members. Login required if off-campus.
Date: December 2019
Creator: Yeganehtalab, Babak
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Control and Automation of a Heat Shrink Tubing Process

Description: Heat shrink tubing is used to insulate wire conductors, protect wires, and to create cable entry seals in wire harnessing industries. Performing this sensitive process manually is time consuming, the results are strongly dependent on the operator’s expertise, and the process presents safety concerns. Alternatively, automating the process minimizes the operators’ direct interaction, decreases the production cost over the long term, and improves quantitative and qualitative production indicators … more
Date: August 2014
Creator: Yousefi Darani, Shahrokh
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Corrosion Protection of Low Carbon Steel By Cation Substituted Magnetite

Description: Surfaces of low carbon steel sheet were modified by exposure to highly caustic aqueous solutions containing either chromium or aluminum cations. Corrosion resistances of such surfaces were compared with that of steel surfaces exposed to plain caustic aqueous solution. In all cases a highly uniform, black coating having a spinel structure similar to magnetite (Fe3O4) was obtained. The coated steel surfaces were characterized using X-ray photoelectron spectroscopy (XPS), scanning electron micros… more
Date: May 2013
Creator: Phadnis, Ameya
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

The Design and Development of Lightweight Composite Wall, Roof, and Floor Panels for Rigid Wall Shelter

Description: This thesis presents a research effort aimed at developing a stronger, lighter, and more economic shelter using rigid wall panels. Reported herein is insulation research, wall and roof panel design and testing, floor section modeling and strength calculations, and cost and weight calculations. Beginning stages focus on developing solid wall and roof panels using cold-formed steel corrugated sheathing and members, as well as polyurethane spray foam for insulation. This research includes calculat… more
Date: May 2018
Creator: Artman, Jeremy J
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Design Method of Cold-Formed Steel Framed Shear Wall Sheathed by Structural Concrete Panel

Description: The objective of this research is developing a new method of design for cold-formed steel framed shear wall sheathed by ¾" thick USG structural panel concrete subfloor using a predictive analytical model and comparing the results obtained from the model with those achieved from real testing to verify the analytical model and predicted lateral load-carrying capacity resulted from that. Moreover, investigating the impact of various screw spacings on shear wall design parameter such as ultimate st… more
Access: Restricted to UNT Community Members. Login required if off-campus.
Date: December 2019
Creator: Ashkanalam, Aida
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Design, Modeling, and Experiment of a Piezoelectric Pressure Sensor based on a Thickness-Shear Mode Crystal Resonator

Description: This thesis presents the design, modeling, and experiment of a novel pressure sensor using a dual-mode AT-cut quartz crystal resonator with beat frequency analysis based temperature compensation technique. The proposed sensor can measure pressure and temperature simultaneously by a single AT-cut quartz resonator. Apart from AT-cut quartz crystal, a newly developed Langasite (LGS) crystal resonator is also considered in the proposed pressure sensor design, since LGS can operate in a higher tempe… more
Date: May 2017
Creator: Pham, Thanh Tuong
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Development and Test of High-Temperature Piezoelectric Wafer Active Sensors for Structural Health Monitoring

Description: High-temperature piezoelectric wafer active sensors (HT-PWAS) have been developed for structure health monitoring at hazard environments for decades. Different candidates have previously been tested under 270 °C and a new piezoelectric material langasite (LGS) was chosen here for a pilot study up to 700 °C. A preliminary study was performed to develop a high temperature sensor that utilizes langasite material. The Electromechanical impedance (E/M) method was chosen to detect the piezoelectric p… more
Date: December 2014
Creator: Bao, Yuanye
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Direct Immersion Cooling Via Nucleate Boiling of HFE-7100 Dielectric Liquid on Hydrophobic and Hydrophilic Surfaces

Description: This study experimentally investigated the effect of hydrophobic and hydrophilic surfaces characteristics on nucleate boiling heat transfer performance for the application of direct immersion cooling of electronics. A dielectric liquid, HFE – 7100 was used as the working fluid in the saturated boiling tests. Twelve types of 1-cm2 copper heater samples, simulating high heat flux components, featured reference smooth copper surface, fully and patterned hydrophobic surface and fully and patterned … more
Date: December 2014
Creator: Joshua, Nihal E.
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Direct Strength Method for Web Crippling of Cold-formed Steel C-sections

Description: Web crippling is a form of localized buckling that occurs at points of transverse concentrated loading or supports of thin-walled structural members. The theoretical computation of web crippling strength is quite complex as it involves a large number of factors such as initial imperfections, local yielding at load application and instability of web. The existing design provision in North American specification for cold-formed steel C-sections (AISI S100, 2007) to calculate the web-crippling str… more
Date: May 2013
Creator: Seelam, Praveen Kumar Reddy
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Drive Level Dependence of Advanced Piezoelectric Resonators

Description: Resonators are one of the most important parts of electronic products. They provide a stable reference frequency to ensure the operation of these products. Recently, the electronic products have the trend of miniaturization, which rendered the size reduction of the resonators as well [1]. Better design of the resonators relies on a better understanding of the crystals' nonlinear behavior [2]. The nonlinearities affect the quality factor and acoustic behavior of MEMS (Micro-Electro-Mechanical-Sy… more
Date: August 2012
Creator: Xie, Yuan
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Dynamic Behaviors of Historical Wrought Iron Truss Bridges – a Field Testing Case Study

Description: Civil infrastructure throughout the world serves as main arteries for commerce and transportation, commonly forming the backbone of many societies. Bridges have been and remain a crucial part of the success of these civil networks. However, the crucial elements have been built over centuries and have been subject to generations of use. Many current bridges have outlived their intended service life or have been retrofitted to carry additional loads over their original design. A large number of t… more
Date: December 2015
Creator: Hedric, Andrew C.
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Effect of Polyphosphoric Acid on Aging Characteristics of PG 64-22 Asphalt Binder

Description: This research presents the results on an experimental investigation to identify the effect of polyphosphoric acid (PPA) on aging characteristics of an asphalt binder. Addition of PPA to asphalt binders is said to improve performance of flexible pavements. Asphalt binder PG 64-22 in modified and unmodified conditions was subjected to aging in the laboratory using a regular oven and also simulated short term aging using rolling thin film oven (RTFO) test. Aging experiments were conducted to analy… more
Date: December 2010
Creator: Ramasamy, Naresh Baboo
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Effects of Minimum Quantity Lubrication (Mql) on Tool Life in Drilling Aisi 1018 Steel

Description: It has been reported that minimum quantity lubrication (MQL) provides better tool life compared to flood cooling under some drilling conditions. In this study, I evaluate the performance of uncoated HSS twist drill when machining AISI 1018 steel using a newly developed lubricant designed for MQL (EQO-Kut 718 by QualiChem Inc.). A randomized factorial design was used in the experiment. The results show that a tool life of 1110 holes with a corresponding flank wear of 0.058 mm was realized.
Date: August 2012
Creator: Maru, Tejas
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Effects of Processing Techniques on Mechanical Properties of Selected Polymers

Description: The mechanical properties of a polymer represent the critical characteristics to be considered when determining the applications for it. The same polymer processed with different methods can exhibit different mechanical properties. The purpose of this study is to investigate the difference in mechanical properties of the selected polymers caused by different processing techniques and conditions. Three polymers were studied, including low density polyethylene (LDPE), polypropylene (PP), and NEXP… more
Date: May 2013
Creator: Dong, Yao
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Effects of Rebar Temperature and Water to Cement Ratio on Rebar-Concrete Bond Strength of Concrete Containing Fly Ash

Description: This research presents the results on an experimental investigation to identify the effects of rebar temperature, fly ash and water to cement ratio on concrete porosity in continuously reinforced concrete pavements (CRCP). Samples were cast and analyzed using pullout tests. Water to cement ratio (w/c) and rebar temperature had a significant influence on the rebar-concrete bond strength. The 28-day shear strength measurements showed an increase in rebar-concrete bond strength as the water to cem… more
Date: May 2010
Creator: Pati, Ardeep Ranjan
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
Back to Top of Screen