You limited your search to:

  Partner: UNT Libraries
 Department: Department of Engineering Technology
 Decade: 1990-1999
 Collection: UNT Theses and Dissertations
A Computer-Based Process Control System for a Target Station in a LINAC Facility

A Computer-Based Process Control System for a Target Station in a LINAC Facility

Date: May 1999
Creator: Al-Shantaf, Abdulraouf O.
Description: An event-driven, sequential, process control system was designed for International Isotopes, Inc., to automate and remotely control a target station at the company's linear accelerator facility. The designed system consisted of two major sections: a software program (virtual instrument), which was developed by LabVIEW, and a hardware interface (FieldPoint Modular Distributed I/O System by National Instrument), which had to be a pre-developed system that did not require customization. The designed virtual instrument was tested on a simulation model that mimed the target station. The result was a valid design.
Contributing Partner: UNT Libraries
Design of a Monitoring System for a Plasma Cleaning Machine

Design of a Monitoring System for a Plasma Cleaning Machine

Date: May 1999
Creator: Fooks, Terry M. (Terry Max)
Description: Plasma cleaning is the most effective dry process to remove surface contaminates from a SAW (Surface Acoustical Wave) device. Consistent gas pressures, flows, and good electrical connections between the chamber shelves are necessary for the process to function predictably. In addition, operation of the monitoring system must be transparent to the plasma cleaning unit. This thesis describes a simple solution to the complex problem of monitoring a plasma cleaning system. The monitoring system uses the LabVIEW® G programming language and hardware, both products of National Instruments, Inc.®, to monitor critical parameters necessary to achieve a consistent process when cleaning these devices.
Contributing Partner: UNT Libraries
Development of a coaxiality indicator

Development of a coaxiality indicator

Access: Use of this item is restricted to the UNT Community.
Date: December 1999
Creator: Arendsee, Wayne C.
Description: The geometric dimensioning and tolerancing concept of coaxiality is often required by design engineers for balance of rotating parts and precision mating parts. In current practice, it is difficult for manufacturers to measure coaxiality quickly and inexpensively. This study examines feasibility of a manually-operated, mechanical device combined with formulae to indicate coaxiality of a test specimen. The author designs, fabricates, and tests the system for measuring coaxiality of holes machined in a steel test piece. Gage Repeatability and Reproducibility (gage R&R) and univariate analysis of variance is performed in accordance with Measurement System Analysis published by AIAG. Results indicate significant design flaws exist in the current configuration of the device; observed values vary greatly with operator technique. Suggestions for device improvements conclude the research.
Contributing Partner: UNT Libraries
Development of a Simplified Fracture Toughness Tool for Polymers

Development of a Simplified Fracture Toughness Tool for Polymers

Date: August 1997
Creator: Marnock, Patrick J. (Patrick Joseph)
Description: This thesis presents research toward the development of a simple inexpensive fracture toughness tool for polymeric materials. Experiments were conducted to test the specimen configuration and the fracture toughness tool against an established ASTM standard for polymer fracture toughness, D5045, and a commonly used four-point bend method. The materials used in this study were polycarbonate and high density polyethylene. Reductions in both the production time and the variability resulting from the preparation of the specimens were addressed through the use of specially designed fixtures. The effects from the razor cut depths used in the chevron notch were compared to the fracture toughness values obtained in order to determine the effect upon the validity of the fracture toughness.
Contributing Partner: UNT Libraries
Fracture Toughness Testing of Plastics under Various Environmental Conditions

Fracture Toughness Testing of Plastics under Various Environmental Conditions

Date: December 1997
Creator: Velpuri, Seshagirirao V.
Description: The primary objective of this study is to test the applicability to plastics of a fracture toughness testing tool developed for metals. The intent is to study pre-test conditioning of several plastic materials and the effect of the depth of the razor notch cut in the chevron notched fracture toughness test specimens. The study includes the careful preparation of samples followed by conditioning in various environments. Samples were subjected to laboratory air for a specific duration or to a controlled temperature-humidity condition as per the ASTM D1870. Some of the samples were subjected to vacuum conditioning under standard test specifications. Testing was conducted using the conventional three-point bend test as per ASTM D5045-95. ASTM E1304, which sets a standard for short rod and bar testing of metals and ceramics provides some basis for conducting chevron notched four-point bend tests to duplicate the toughness tool. Correlation of these results with the ASTM test samples is determined. The four-point bend test involves less specimen machining as well as time to perform the fracture toughness tests. This study of fracture toughness testing has potential for quality control as well as the fracture property determination.
Contributing Partner: UNT Libraries