You limited your search to:

  Partner: UNT Libraries
 Department: Department of Electrical Engineering
 Degree Discipline: Electrical Engineering
 Collection: UNT Theses and Dissertations
Design and Implementation of Broad Band and Narrow Band Antennas and Their Applications

Design and Implementation of Broad Band and Narrow Band Antennas and Their Applications

Date: August 2011
Creator: Salmani, Zeeshan
Description: The thesis deals with the design and implementation of broadband and narrowband antennas and their applications in practical environment. In this thesis, a new concept for designing the UWB antenna is proposed based on the CRLH metamaterials and this UWB antenna covers a frequency range from 2.45 GHz to 11.6 GHz. Based on the design of the UWB antenna, another antenna is developed that can cover a very wide bandwidth i.e from 0.66 GHz to 120 GHz. This antenna can not only be used for UWB applications but also for other communication systems working below the UWB spectrum such as GSM, GPS, PCS and Bluetooth. The proposed antenna covering the bandwidth from 0.66 GHz to 120 GHz is by far the largest bandwidth antenna developed based on metamaterials. Wide band antennas are not preferred for sensing purpose as it is difficult to differentiate the received signals. A multiband antenna which can be used as a strain sensor for structural health monitoring is proposed. The idea is to correlate the strain applied along the length or width with the multiple resonant frequencies. This gives the advantage of detecting the strain applied along any direction (either length or width), thus increasing the ...
Contributing Partner: UNT Libraries
Design and Implementation of Communication Platform for Autonomous Decentralized Systems

Design and Implementation of Communication Platform for Autonomous Decentralized Systems

Date: December 2010
Creator: Gottipati, Naga Sravani
Description: This thesis deals with the decentralized autonomous system, in which individual nodes acting like peers, communicate and participate in collaborative tasks and decision making processes. An experimental test-bed is created using four Garcia robots. The robots act like peers and interact with each other using user datagram protocol (UDP) messages. Each robot continuously monitors for messages coming from other robots and respond accordingly. Each robot broadcasts its location to all the other robots within its vicinity. Robots do not have built-in global positioning system (GPS). So, an indoor localization method based on signal strength is developed to estimate robot's position. The signal strength that the robot gets from the nearby wireless access points is used to calculate the robot's position. Trilateration and fingerprint are some of the indoor localization methods used for this purpose. The communication functionality of the decentralized system has been tested and verified in the autonomous systems laboratory.
Contributing Partner: UNT Libraries
Design of a Dual Band Gan Pa Utilizing Dual Band Impedance Transformers

Design of a Dual Band Gan Pa Utilizing Dual Band Impedance Transformers

Date: May 2013
Creator: Poe, David R.
Description: This thesis discusses the design, fabrication, and testing of a high efficiency, dual band radio frequency power amplifier. While it is difficult to demonstrate an exact mode of operation for power amplifiers at radio frequencies, based on the characteristics of the transistor itself, the argument can be made that our high efficiency performance is due to an approximation to class E operation. The PA is designed around a CGH40025 transistor manufactured by Cree, Inc, which has developed a very useful nonlinear model of its transistor, which allows use of software load/source pull methods to determine optimum impedances to be presented to the gate and drain (hereafter referred to as source and load) of the transistor at each band of operation. A recent work on dual-band impedance matching is then used to design distributed element networks in order to present conjugate matches of these impedances to the transistor. This is followed by a careful layout, after which the PA is then fabricated on a low-impedance substrate using a LPKF Protomat S63 rapid prototyping machine. Measurements of gain and drain current provide values for power-added-efficiency. Simulated gains were 21 and 18 dB at 800 MHz and 1.85 GHz, respectively, with PAE around ...
Contributing Partner: UNT Libraries
Design of a Wideband Class J Power Amplifier

Design of a Wideband Class J Power Amplifier

Date: May 2013
Creator: Raavi, Srinivasa
Description: A conventional RF power amplifier will convert the low powered radio frequency signals into high powered signals. Along with the expected ability to increase the communication distance, data transfer rates, RF power amplifiers also have many applications which include military radar system, whether forecasting, etc. The main objective of any power amplifier research is to increase the efficiency while maintaining linearity and broadening the frequency of operation. The main motivation for the renewed interest in PA technology comes from the technical challenges and the economics of modern digital communication systems. Modern communications require high linear power amplifiers and in order to reduce the complete system cost, it is necessary to have a single broadband power amplifier, which can amplify multiple carriers. The improvement in the efficiency of the power amplifier increases the battery life and also reduces the cooling requirements for the same output power. In this thesis, I aim to design and build a wideband class J power amplifier suitable for modern communications. For wideband operation of the GaN technology PA, a bandwidth extension design method is studied and implemented. The simulation results are proved to have a good argument with the theoretical calculations.
Contributing Partner: UNT Libraries
Development Of A Testbed For Multimedia Environmental Monitoring

Development Of A Testbed For Multimedia Environmental Monitoring

Date: December 2011
Creator: Kandula, Harsha
Description: Multimedia environmental monitoring involves capturing valuable visual and audio information from the field station. This will permit the environmentalists and researchers to analyze the habitat and vegetation of a region with respect to other environmental specifics like temperature, soil moisture, etc. This thesis deals with the development of a test bed for multimedia monitoring by capturing image information and making it available for the public. A USB camera and a Single board computer are used to capture images at a specified frequency. A web-client is designed to display the image data and establish a secured remote access to reconfigure the field station. The development includes two modes of image acquisition including a basic activity recognition algorithm. Good quality images are captured with the cost for development of the system being less than 2 hundred dollars.
Contributing Partner: UNT Libraries
Development of Indium Oxide Nanowires as Efficient Gas Sensors

Development of Indium Oxide Nanowires as Efficient Gas Sensors

Access: Use of this item is restricted to the UNT Community.
Date: December 2011
Creator: Gali, Pradeep
Description: Crystalline indium oxide nanowires were synthesized following optimization of growth parameters. Oxygen vacancies were found to impact the optical and electronic properties of the as-grown nanowires. Photoluminescence measurements showed a strong U.V emission peak at 3.18 eV and defect peaks in the visible region at 2.85 eV, 2.66 eV and 2.5 eV. The defect peaks are attributed to neutral and charged states of oxygen vacancies. Post-growth annealing in oxygen environment and passivation with sulphur are shown to be effective in reducing the intensity of the defect induced emission. The as-grown nanowires connected in an FET type of configuration shows n-type conductivity. A single indium oxide nanowire with ohmic contacts was found to be sensitive to gas molecules adsorbed on its surface.
Contributing Partner: UNT Libraries
Development of Silicon Nanowire Field Effect Transistors

Development of Silicon Nanowire Field Effect Transistors

Access: Use of this item is restricted to the UNT Community.
Date: December 2011
Creator: Nukala, Prathyusha
Description: An economically reliable technique for the synthesis of silicon nanowire was developed using silicon chloride as source material. The 30-40 micron long nanowires were found to have diameters ranging from 40 – 100 nm. An amorphous oxide shell covered the nanowires, post-growth. Raman spectroscopy confirmed the composition of the shell to be silicon-dioxide. Photoluminescence measurements of the as-grown nanowires showed green emission, attributed to the presence of the oxide shell. Etching of the oxide shell was found to decrease the intensity of green emission. n-type doping of the silicon nanowires was achieved using antimony as the dopant. The maximum dopant concentration was achieved by post-growth diffusion. Intrinsic nanowire parameters were determined by implementation of the as-grown and antimony doped silicon nanowires in field effect transistor configuration.
Contributing Partner: UNT Libraries
Development of Wireless Sensor Network System for Indoor Air Quality Monitoring

Development of Wireless Sensor Network System for Indoor Air Quality Monitoring

Date: December 2012
Creator: Borkar, Chirag
Description: This thesis describes development of low cost indoor air quality (IAQ) monitoring system for research. It describes data collection of various parameters concentration present in indoor air and sends data back to host PC for further processing. Thesis gives detailed information about hardware and software implementation of IAQ monitoring system. Also discussed are building wireless ZigBee network, creating user friendly graphical user interface (GUI) and analysis of obtained results in comparison with professional benchmark system to check system reliability. Throughputs obtained are efficient enough to use system as a reliable IAQ monitor.
Contributing Partner: UNT Libraries
Dual-band Microwave Components And Their Applications

Dual-band Microwave Components And Their Applications

Date: December 2011
Creator: Shao, Jin
Description: In general, Dual-Band technology enables microwave components to work at two different frequencies. This thesis introduces novel dual-band microwave components and their applications. Chapter 2 presents a novel compact dual-band balun (converting unbalanced signals to balanced ones). The ratio between two working frequencies is analyzed. A novel compact microstrip crossover (letting two lines to cross each other with very high isolation) and its dual-band application is the subject of chapter 3. A dual-frequency cloak based on lumped LC-circuits is introduced in chapter 4. In chapter 5, a dual-band RF device to detect dielectric constant changes of liquids in polydimethylsiloxane (PDMS) microfluidic channels has been presented. Such a device is very sensitive, and it has significantly improved the stability. Finally, conclusion of this thesis and future works are given in chapter 6.
Contributing Partner: UNT Libraries
Electronic Sound Analysis with Hardware System and Remote Internet Display

Electronic Sound Analysis with Hardware System and Remote Internet Display

Access: Use of this item is restricted to the UNT Community.
Date: August 2010
Creator: McCord, Cameron Forrest
Description: Currently, standards from government agencies such as the National Institute for Occupation Safety and Health exist to aid in safeguarding individuals’ capacity for hearing, but only in factory settings in which large machines often produce loud levels of sound. Neglecting the fact that these preventative measures are only in place in the most limited of settings, no system currently exists to observe and report sound exposure levels in a manner timely or easily recognizable enough to adequately serve its purpose of hearing conservation. Musicians may also incur significant levels of risk for hearing loss in their day-to-day rehearsals and concerts, from high school marching bands to university wind bands. As a result, music school accrediting organizations such as the National Association of Schools of Music and even the European Union have begun taking steps meant to determine the risks associated with music. To meet these goals and improve upon current technologies, a system has been developed that electronically records sound levels utilizing modern hardware, increases the speed of reporting by transmitting data over computer networks and the Internet, and displays measures calculated from these data in a web browser for a highly viewable, user-friendly interface.
Contributing Partner: UNT Libraries