UNT Theses and Dissertations - 245 Matching Results

Search Results

prev Results: 21 - 44 next

Photophysical Interactions in Vapor Synthesized and Mechanically Exfoliated Two-Dimensional Conducting Crystallites for Quantum and Optical Sensing

Description: In the first study, superconducting 2D NbSe₂ was examined towards its prototypical demonstration as a transition-edge sensor, where photoexcitation caused a thermodynamic phase transition in NbSe₂ from the superconducting state to the normal state. The efficacy of the optical absorption was found to depend on the wavelength of the incoming radiation used, which ranged from the ultra-violet (405 nm), visible (660 nm), to the infrared (1060 nm). In the second case involving WSe₂, the UV-ozone tr… more
This item is restricted from view until September 1, 2024.
Date: August 2022
Creator: Jayanand, Kishan
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Processing-Structure Relationships of Reactive Spark Plasma Sintered Diamond Composites

Description: Traditional lightweight armor ceramics such as boron carbide (B4C) and silicon carbide (SiC) are used alone or together in varying amounts to create monolithic protective plates. These materials exhibit relatively small differences in hardness, flexure strength, and fracture toughness. Many of the routes taken during the synthesis of the powder and sintering of the plates using traditional ceramic processing techniques have long processing times, tend to leave asperities within the microstruc… more
Date: August 2022
Creator: Garcia, Christian
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Time-Dependent Deformation Mechanisms in Metallic Glasses as a Function of Their Structural State

Description: In this study, the time-dependent deformation behavior of several model bulk metallic glasses (BMGs) was studied. The BMGs were obtained in different structural states by thermal relaxation below their glass transition temperature, cryogenic thermal cycling, and chemical rejuvenation by micro-alloying. The creep behavior of Zr52.5Ti5Cu17.9Ni14.6Al10 BMG in different structural states was investigated as a function of peak load and temperature. The creep strain rate sensitivity (SRS) indicated a… more
This item is restricted from view until June 1, 2024.
Date: May 2022
Creator: Ghodki, Nandita
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Effect of Modifier Cation Substitution on Structure and Properties of Bioactive Glasses from Molecular Dynamics Simulations

Description: Bioactive glass is a type of third generation bioactive material that can bond to both soft and hard tissue with applications ranging from bone defect repair, coatings for metallic implants, to scaffolds for tissue engineering. Design of bioactive glasses for these applications rely on a detailed understanding of the structures of these glasses which are complicated and multicomponent. In this thesis, I have applied molecular dynamics (MD) simulations with interatomic potentials developed in ou… more
Date: May 2022
Creator: Vu, Myra
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Fabrication of the Novel Asymmetric Polymeric Materials via Bottom-Up Approach

Description: Asymmetric polymeric materials can be formed by either top-down or bottom-up methods. Bottom-up methods involve assembling the atoms and molecules to form small nanostructures by carefully controlled synthesis, which results in a reduction of some of the top-down limitations. In this dissertation, thermal, tribological and antireflective properties of polymeric materials have been enhanced by introducing structural asymmetry. The overall performance of commercial polymeric coatings, e.g. epoxy … more
Date: May 2022
Creator: Hnatchuk, Nataliia
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Corrosion Behavior of High Entropy Alloys in Molten Chloride and Molten Fluoride Salts

Description: High entropy alloys (HEAs) or complex concentrated alloys (CCAs) represent a new paradigm in structural alloy design. Molten salt corrosion behavior was studied for single-phase HEAs such as TaTiVWZr and HfTaTiVZr, and multi-phase HEAs such as AlCoCrFeNi2.1. De-alloying with porosity formation along the exposed surface and fluxing of unstable oxides were found to be primary corrosion mechanisms. Potentiodynamic polarization study was combined with systematic mass–loss study for TaTiVWZr, HfTaT… more
This item is restricted from view until June 1, 2024.
Date: May 2022
Creator: Patel, Kunjalkumar Babubhai
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Integration, Stability, and Doping of Mono-Elemental and Binary Transition Metal Dichalcogenide Van der Waals Solids for Electronics and Sensing Devices

Description: In this work, we have explored 2D semiconducting transition metal dichalcogenides (TMDs), black phosphorus (BP), and graphene for various applications using liquid and mechanical exfoliation routes. The topical areas of interest that motivate our work include considering factors such as device integration, stability, doping, and the effect of gasses to modulate the electronic transport characteristics of the underlying 2D materials. In the first area, we have integrated solution-processed trans… more
This item is restricted from view until June 1, 2024.
Date: May 2022
Creator: Mehta, Ravindra K
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Characterization and Chemical Analysis of Fundamental Components for Lead Acid Batteries

Description: Although markets for alternative batteries, such as Li-ion, are growing, Pb-alloy batteries still dominate the market due to their low cost and good functionality. Even though these Pb-alloy batteries have been around since their discovery in 1859, little research involving advanced characterization techniques, such as synchrotron radiation X-ray diffraction (SR-XRD) and transmission electron diffraction (TEM) have been performed on Pb-alloys and sulfation, a failure mode in lead acid batteries… more
Date: May 2022
Creator: Wall, Michael T
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Design and Performance of Metal Matrix Composite Composed of Porous Boron Carbide Created by Magnetic Field-Assisted Freeze Casting Infiltrated with Aluminum (A356)

Description: Magnetic field-assisted freeze-casting was used to create porous B4C ceramic preforms. An optimum slurry consisted of a mixture of B4C powders with 6 wt.% Er2O3 powder in an H2O-PVA solution and was cooled at a rate of 1 °C/min from room temperature to -30 °C resulting in porous green state ceramic preform with vertical channels. The Er2O3 powder was added to improve the magnetic response of the slurry. The preform was then sublimated to remove H2O and then sintered. The sintered ceramic prefor… more
Date: May 2022
Creator: Gamboa, Gerardo
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

A Study on High Pressure-Induced Phase Transformations of a Metastable Complex Concentrated Alloy System with Varying Amounts of Copper

Description: Complex concentrated alloys (CCAs) offer the unique ability to tune composition and microstructure to achieve a wide range of mechanical performance. Recently, the development of metastable CCAs has led to the creation of transformation-induced plasticity (TRIP) CCAs. Similar to TRIP steels, TRIP CCAs are more effective at absorbing high strain rate loads when TRIP is activated during the loading process. The objective of our study is to investigate the effect of copper on the critical pressure… more
Date: May 2022
Creator: Reynolds, Christopher
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Mechanically Driven Reconstruction of Materials at Sliding Interfaces to Control Wear

Description: To minimize global carbon emissions, having efficient jet engines and internal combustion engines necessitates utilizing lightweight alloys such as Al, Ti, and Mg-based alloys. Because of their remarkable strength/weight ratio, these alloys have received a lot of attention. Nonetheless, they have very poor tribological behavior, particularly at elevated temperatures beyond 200 °C, when most liquid lubricants begin to fail in lubrication. Over the last two decades, there has been a lot of intere… more
Date: May 2022
Creator: Shirani, Asghar
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Considerations in Designing Alloys for Laser-Powder Bed Fusion Additive Manufacturing

Description: This work identifies alloy terminal freezing range, columnar growth, grain coarsening, liquid availability towards the terminal stage of solidification, and segregation towards boundaries as primary factors affecting the hot-cracking susceptibility of fusion-based additive manufacturing (F-BAM) processed alloys. Additionally, an integrated computational materials engineering (ICME)-based approach has been formulated to design novel Al alloys, and high entropy alloys for F-BAM processing. The IC… more
This item is restricted from view until June 1, 2027.
Date: May 2022
Creator: Thapliyal, Saket
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Tuning of Microstructure and Mechanical Properties in Additively Manufactured Metastable Beta Titanium Alloys

Description: The results from this study, on a few commercial and model metastable beta titanium alloys, indicate that the growth restriction factor (GRF) model fails to interpret the grain growth behavior in the additively manufactured alloys. In lieu of this, an approach based on the classical nucleation theory of solidification incorporating the freezing range has been proposed for the first time to rationalize the experimental observations. Beta titanium alloys with a larger solidification range (liquid… more
This item is restricted from view until June 1, 2024.
Date: May 2022
Creator: Nartu, Mohan Sai Kiran Kumar Yadav
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Wear, Friction and High Shear Strain Deformation of Metallic Glasses

Description: In this work, wear and scratch behavior of four different bulk metallic glasses (BMGs) namely Zr41.2Cu12.5Ni10Ti13.8Be22.5 (LM 1), Zr57Cu15.4Ni12.6Al10Nb5 (LM 106), Ni60Pd20P17B3 (Ni-BMG), and Pt57.5Cu14.7Ni5.3P22.5 (Pt-BMG) were compared. Shear band formation on the edges of the scratch groove with spallation was found to be the primary failure mechanism in progressive scratch tests. The wear behavior and the scratch response of model binary Ni-P metallic glasses was systematically studied as … more
This item is restricted from view until June 1, 2024.
Date: May 2022
Creator: Pole, Mayur
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Unraveling the Effect of Atomic Configurations and Structural Statistics on Mechanical Behavior of Multicomponent and Amorphous Alloys

Description: Multicomponent high-entropy and amorphous alloys represent relatively new classes of structural materials with complex atomic configurations and exceptional mechanical properties. However, there are several knowledge gaps in the relationships between their atomic structure and mechanical properties. Understanding these critical relationships will enable novel alloy design and tailoring of their mechanical properties for desired engineering applications. In this dissertation, first-principles ca… more
Date: December 2021
Creator: Yang, Yu Chia
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Materials Approaches for Transparent Electronics

Description: This dissertation tested the hypothesis that energy transferred from a plasma or plume can be used to optimize the structure, chemistry, topography, optical and electrical properties of pulsed laser deposited and sputtered thin-films of ZnO, a-BOxNy, and few layer 2H-WS2 for transparent electronics devices fabricated without substrate heating or with low substrate heating. Thus, the approach would be compatible with low-temperature, flexible/bendable substrates. Proof of this concept was demons… more
Date: December 2021
Creator: Iheomamere, Chukwudi E.
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

First Principles Study of the Effect of Local Bonding on Diffusion Mechanisms in Alloys

Description: This work demonstrates how local, randomized tailoring of bond stiffness can affect the activation energy of diffusion in model alloys using density functional theory-based computations. This work is organized into two parts. The first part deals with the vacancy diffusion mechanism, and it compares the in–plane (IP) vs out-of-plane (OOP) diffusion paths in prototypical binary Mg-X (Ca, Y, and Gd) and ternary Mg-X (Ca, Y, and Gd)-Zn alloys. We examine how vacancy formation, migration, and solut… more
Date: December 2021
Creator: Paranjape, Priyanvada Madhukar
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Additive Manufacturing of AZ31B Magnesium Alloy via Friction Stir Deposition

Description: Additive friction stir deposition (AFSD) of AZ31B magnesium alloy was conducted to examine evolution of grain structure, phases, and crystallographic texture. AFSD was carried out using a hollow tool made from tool steel at a constant rotational velocity of 400 rpm on the AZ31B base plate. Bar stock of AZ31B was utilized as a feed material. The linear velocity of the tool was varied in the range of 4.2-6.3 mm/s. The feed rate of the material had to be maintained at a half value compared to the … more
Date: December 2021
Creator: Patil, Shreyash Manojkumar
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Thermokinetics-Dependent Microstructural Evolution and Material Response in Laser-Based Additive Manufacturing

Description: Laser-based additive manufacturing offers a high degree of thermokinetic flexibility that has implications on the structure and properties of the fabricated component. However, to exploit the flexibility of this process, it is imperative to understand the process-inherent thermokinetic evolution and its effect on the material characteristics. In view of this, the present work establishes a fundamental understanding of the spatiotemporal variation of thermokinetics during the fabrication of the … more
Date: December 2021
Creator: Pantawane, Mangesh V
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Advanced Cathodes for High Energy Density Lithium Sulfur Battery

Description: A systematic development of 2D alloy catalyst with synergistic performance of high lithium polysulfide (LiPS) binding energy and efficient Li+ ion/electron conduction is presented. The first section of work found that Li+ ions can flow through the percolated ion transport pathway in polycrystalline MoS2, while Na+ and K+ ions can easily flow through the percolated 1D ion channel near the grain boundaries. An unusually high ionic conductivity of extrinsic Li+, Na+, and K+ ions in 2D MoS2 film ex… more
Date: December 2021
Creator: Bhoyate, Sanket
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Fractography and Mechanical Properties of Laminated Alumina and Yttria Stabilized Zirconia

Description: Yttria stabilized zirconia (YSZ) is a polymorph with possible phase transformation toughening occurring during impact. The fractography and mechanical properties of laminated alumina and YSZ were studied in this thesis. Five sample types were studied in this thesis: (5:5) Al2O3/YSZ (a sequence of 5 alumina tapes stacked on 5 YSZ tapes), (5:5) Al2O3/YSZ (1 wt.% Pure ZrO2), (7:3) Al2O3/YSZ, Al2O3, and YSZ. Scanning electron microscopy (SEM) and X-ray microscopy (XRM) were used to study morphology… more
Date: December 2021
Creator: Cotton, Shomari Johnny
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
open access

Structural and Magnetic Properties of Additively Manufactured Hiperco (FeCo-2V)

Description: The FeCo-V alloy, commercially referred to as Hiperco, is known for its great soft magnetic properties. However, the high cost of production has limited the usage of this alloy to small-scale applications, where the small volume and high magnetic performance are critical. Additive manufacturing (AM) has the potential to solve the production problems that exist in Hiperco manufacturing. The present research has focused on selective laser melting (SLM) based AM processing of Hiperco. The goal was… more
Date: December 2021
Creator: O'Donnell, Aidan James
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Self-Healing Ceramics for High Temperature Application

Description: Ceramics have a wide variety of applications due to their unique properties; however, the low fracture toughness leads the formation and propagation of unpredictable cracks, and reduces their reliability. To solve this problem, self-healing adaptive oxides were developed. The aim of the work is to gain new insights into self-healing mechanisms of ceramics and their application. Binary oxide systems were investigated that are at least partially healed through the extrinsic or intrinsic addition … more
Date: August 2021
Creator: Gu, Jingjing
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries

Synergistic Effects of Lattice Instability and Chemical Ordering on FCC Based Complex Concentrated Alloys

Description: The current work investigates how the interactions among constituent elements in high entropy alloys or complex concentrated alloys (HEA/CCAs) can lead to lattice instability and local chemical ordering which in turn affects the microstructure and properties of these alloys. Using binary enthalpies of mixing, the degree of ordering in concentrated multi-component solid solutions was successfully tailored by introducing Cr, Al and Ti in a CoFeNi HEA/CCA. CoFeNi was selected as the base alloy to … more
Date: August 2021
Creator: Dasari, Sriswaroop
Item Type: Refine your search to only Thesis or Dissertation
Partner: UNT Libraries
Back to Top of Screen