You limited your search to:

  Partner: UNT Libraries Government Documents Department
 Serial/Series Title: NACA Special Report
 Collection: Technical Report Archive and Image Library
N.A.C.A. Stall-Warning Device

N.A.C.A. Stall-Warning Device

Date: February 1938
Creator: Thompson, F.L.
Description: With some airplanes the approach to the stall is accompanied by changes in the behavior, such as tail buffeting or changes in the control characteristics of the airplane so that the pilot obtains a warning of the impending stall. Vith other airplanes it is possible to approach the stall without any perceptible warning other than the reading of the air-speed meter, in which case the danger of inadvertent stalling is considerably greater. Although it is not within the scope of this paper to discuss stalling characteristics, it is desired to point out that in general the danger of inadvertent stalling is greatest with those airplanes that behave worse when the stalling occurs; that is, with airplanes in which the stall starts at the wing tips. A warning of the impending stall is desirable in any case, but is particularly desirable with airplanes of the latter type.
Contributing Partner: UNT Libraries Government Documents Department
Accelerations in Landing with a Tricycle-Type Landing Gear

Accelerations in Landing with a Tricycle-Type Landing Gear

Date: February 1937
Creator: Jones, Robert T.
Description: In connection with the application of stable tricycle-type landing gears to transport airplanes, the question arises as to whether certain passengers may not experience relatively great accelerations in an emergency landing. Since the main landing wheels are behind the center of gravity in this type of gear, a hard-braked landing will cause immediate nosing down of the airplane and, when this motion is stopped due to the front wheel striking the ground, there will be some tendency for the rearmost passengers to be thrown out of their seats, The provided rough calculations are designed to show the magnitudes of the various reactions experienced in a severe landing under these circumstances.
Contributing Partner: UNT Libraries Government Documents Department
An Approximate Method of Calculation of Relative Humidity Required to Prevent Frosting on Inside of Aircraft Pressure Cabin Windows, Special Report

An Approximate Method of Calculation of Relative Humidity Required to Prevent Frosting on Inside of Aircraft Pressure Cabin Windows, Special Report

Date: December 5, 1940
Creator: Jones, Alun R.
Description: This report has been prepare in response to a request for information from an aircraft company. A typical example was selected for the presentation of an approximate method of calculation of the relative humidity required to prevent frosting on the inside of a plastic window in a pressure type cabin on a high speed airplane. The results of the study are reviewed.
Contributing Partner: UNT Libraries Government Documents Department
Boundary-Layer Transition on the N.A.C.A. 0012 and 23012 Airfoils in the 8-Foot High-Speed Wind Tunnel, Special Report

Boundary-Layer Transition on the N.A.C.A. 0012 and 23012 Airfoils in the 8-Foot High-Speed Wind Tunnel, Special Report

Date: January 1, 1940
Creator: Becker, John V.
Description: Determinations of boundary-layer transition on the NACA 0012 and 2301 airfoils were made in the 8-foot high-speed wind tunnel over a range of Reynolds Numbers from 1,600,000 to 16,800,000. The results are of particular significance as compared with flight tests and tests in wind tunnels of appreciable turbulence because of the extremely low turbulence in the high-speed tunnel. A comparison of the results obtained on NACA 0012 airfoils of 2-foot and 5-foot chord at the same Reynolds Number permitted an evaluation of the effect of compressibility on transition. The local skin friction along the surface of the NACA 0012 airfoil was measured at a Reynolds Number of 10,000,000. For all the lift coefficient at which tests were made, transition occurred in the region of estimated laminar separation at the low Reynolds Numbers and approach the point of minimum static pressure as a forward limit at the high Reynolds Numbers. The effect of compressibility on transition was slight. None of the usual parameters describing the local conditions in the boundary layer near the transition point served as an index for locating the transition point. As a consequence of the lower turbulence in the 8-foot high-speed tunnel, the transition points occurred consistently ...
Contributing Partner: UNT Libraries Government Documents Department
A Brief Study of the Speed Reduction of Overtaking Airplanes by Means of Air Brakes, Special Report

A Brief Study of the Speed Reduction of Overtaking Airplanes by Means of Air Brakes, Special Report

Date: May 1, 1942
Creator: Pearson, H. A. & Amderspm. R. F.
Description: As an aid to airplane designers interested in providing pursuit airplanes with decelerating devices intended to increase the firing time when overtaking another airplane, formulas are given relating the pertinent distances and speeds in horizontal flight to the drag increase required. Charts are given for a representative parasite-drag coefficient from which the drag increase, the time gained, and the closing distance may be found. The charts are made up for three values of the ratio of the final speed of the pursuing airplane to the speed of the pursued airplane and for several values of the ratio of the speed of the pursued airplane to the initial speed of the pursuing airplane. Charts are also given indicating the drag increases obtainable with double split flaps and with conventional propellers. The use of the charts is illustrated by an example in which it is indicated that either double split flaps or, under certain ideal conditions, reversible propellers should provide the speed reductions required.
Contributing Partner: UNT Libraries Government Documents Department
The Calculated Effect of Various Hydrodynamic and Aerodynamic Factors on the Take-Off of a Large Flying Boat

The Calculated Effect of Various Hydrodynamic and Aerodynamic Factors on the Take-Off of a Large Flying Boat

Date: June 1, 1939
Creator: Olson, R.E. & Allison, J.M.
Description: Present designs for large flying boats are characterized by high wing loading, high aspect ratio, and low parasite drag. The high wing loading results in the universal use of flaps for reducing the takeoff and landing speeds. These factors have an effect on takeoff performance and influence to a certain extent the design of the hull. An investigation was made of the influence of various factors and design parameters on the takeoff performance of a hypothetical large flying boat by means of takeoff calculations. The parameters varied in the calculations were size of hull (load coefficient), wing setting, trim, deflection of flap, wing loading, aspect ratio, and parasite drag. The takeoff times and distances were calculated to the stalling speeds and the performance above these speeds was studied separately to determine piloting technique for optimum takeoff. The advantage of quick deflection of the flap at high water speeds is shown.
Contributing Partner: UNT Libraries Government Documents Department
Characteristics of NACA 4400R Series Rectangular and Tapered Airfoils, Including the Effect of Split Flaps

Characteristics of NACA 4400R Series Rectangular and Tapered Airfoils, Including the Effect of Split Flaps

Date: January 1941
Creator: Greenberg, Harry
Description: At the request of the Bureau of Aeronautics, Navy Department, tests were made in the variable-density wind tunnel of a tapered wing of 3-10-18 plan form and based on the NACA 4400R series sections. The wing was also tested with 0.2 chord spit flaps, deflected 60 deg span ratios of 0.3, 0.5, 0.7 and 1.0 respectively. In order to get data from which to calculate the characteristics of the flapped wing, the investigation was extended to include tests of the four rectangular airfoils of the NACA 4400R series (4409R, 4412R, 4415R, and 4418R) with full-span 0.2 chord, trailing edge split flaps deflected 60 deg.
Contributing Partner: UNT Libraries Government Documents Department
Comparison of Intercooler Characteristics

Comparison of Intercooler Characteristics

Date: May 1, 1941
Creator: Reuter, J. George & Valerino, Michael F.
Description: A method is presented of comparing the performance, weight, and general dimensional characteristics of inter-coolers. The performance and dimensional characteristics covered in the comparisons are cooling effectiveness, pressure drops and weight flows of the charge and cooling air, power losses, volume, frontal area, and width. A method of presenting intercooler data is described in which two types of charts are plotted; (1) A performance chart setting forth all the important characteristics of a given intercooler and (2) a replot of these characteristics for a number of intercoolers intended to assist in making a selection to satisfy a given set of installation conditions. The characteristics of commercial intercoolers obtained from manufacturers' data and of some computed designs are presented on this basis. A standard test procedure and instrumentation are suggested whereby comparable data may be obtained by different testing organizations.
Contributing Partner: UNT Libraries Government Documents Department
Comparison of Three Exit-Area Control Devices on an N.A.C.A. Cowling, Special Report

Comparison of Three Exit-Area Control Devices on an N.A.C.A. Cowling, Special Report

Date: May 1, 1940
Creator: McHugh, James G.
Description: Adjustable cowling flaps, an adjustable-length cowling skirt, and a bottom opening with adjustable flap were tested as means of controlling the rate of cooling-air flow through an air-cooled radial-engine cowling. The devices were tested in the NACA 20-foot tunnel on a model wing-nacelle-propeller combination, through an airspeed range of 20 to 80 miles per hour, and with the propeller blade angle set 23 degrees at 0.75 of the tip radius. The resistance of the engine to air flow through the cowling was simulated by a perforated plate. The results indicated that the adjustable cowling flap and the bottom opening with adjustable flap were about equally effective on the basis of pressure drop obtainable and that both were more effective means of increasing the pressure drop through the cowling than the adjustable-length skirt. At conditions of equal cooling-air flow, the net efficiency obtained with the adjustable cowling flaps and the adjustable-length cowling skirt was about 1% greater than the net efficiency obtained with the bottom opening with adjustable flap.
Contributing Partner: UNT Libraries Government Documents Department
Compressibility Effects in Aeronautical Engineering

Compressibility Effects in Aeronautical Engineering

Date: August 1, 1941
Creator: Stack, John
Description: Compressible-flow research, while a relatively new field in aeronautics, is very old, dating back almost to the development of the first firearm. Over the last hundred years, researches have been conducted in the ballistics field, but these results have been of practically no use in aeronautical engineering because the phenomena that have been studied have been the more or less steady supersonic condition of flow. Some work that has been done in connection with steam turbines, particularly nozzle studies, has been of value, In general, however, understanding of compressible-flow phenomena has been very incomplete and permitted no real basis for the solution of aeronautical engineering problems in which.the flow is likely to be unsteady because regions of both subsonic and supersonic speeds may occur. In the early phases of the development of the airplane, speeds were so low that the effects of compressibility could be justifiably ignored. During the last war and immediately after, however, propellers exhibited losses in efficiency as the tip speeds approached the speed of sound, and the first experiments of an aeronautical nature were therefore conducted with propellers. Results of these experiments indicated serious losses of efficiency, but aeronautical engineers were not seriously concerned at the ...
Contributing Partner: UNT Libraries Government Documents Department
Correction of Profile-Drag Results from Variable-Density Tunnel and the Effect on the Choice of Wing-Section Thickness

Correction of Profile-Drag Results from Variable-Density Tunnel and the Effect on the Choice of Wing-Section Thickness

Date: March 1, 1938
Creator: Jacobs, Eastman N.
Description: Profile-drag coefficients published from tests in the N.A.C.A. variable-density tunnel (Technical Reports Nos. 460, 537, 586, and 610, references 1 to 4) have tended to appear high as compared with results from the N.A.C.A. full-scale tunnel (Technical Report No. 530, reference 5) and from foreign sources (references 6 to 8). Such discrepancies were considered in Technical Report No. 586, and corrections for turbulence and tip effects were derived that tended to reduce the profile-drag coefficients, particularly for the thicker airfoils. The corrected profile-drag coefficients, designated by the lower-case symbol cdo as contrasted with the older CDO, have been employed in the airfoil reports published since Technical Report No. 460, but even these corrected results continued to appear high, particularly for the thicker sections. The important practical result is that a smaller increase of drag with airfoil thickness is indicated, which may be of primary importance to the airplane designer in choosing the optimum airfoil sections for actual wings. Further investigations of this subject were, of course, undertaken, one of the most important being an investigation of three symmetrical sections N.A.C A. 0009, 0012, and 0018 under conditions of low turbulence in the full-scale tunnel. Preliminary results from this investigation also ...
Contributing Partner: UNT Libraries Government Documents Department
Critical Compressive Stress for Flat Rectangular Plates Supported Along all Edges and Elastically Restrained Against Rotation Along the Unloaded Edges, Special Report 189

Critical Compressive Stress for Flat Rectangular Plates Supported Along all Edges and Elastically Restrained Against Rotation Along the Unloaded Edges, Special Report 189

Date: May 1, 1941
Creator: Lundquist, Eugene E. & Stowell, Eldbridge Z.
Description: A chart is presented for the values of the coefficient in the formula for the critical compressive stress at which buckling may be expected to occur in flat rectangular plates supported along all edges and, in addition, elastically restrained against rotation along the unloaded edges. The mathematical derivations of the formulas required in the construction of the chart are given.
Contributing Partner: UNT Libraries Government Documents Department
Critical Compressive Stress for Outstanding Flanges

Critical Compressive Stress for Outstanding Flanges

Date: April 1, 1941
Creator: Lundquist, Eugene E. & Stowell, Elbridge Z.
Description: A chart is presented for the values of the coefficient in the formula for the critical compressive stress at which buckling may be expected to occur in outstanding flanges. These flanges are flat rectangular plates supported along the Loaded edges, supported and elastically restrained along one unloaded edge, and free along the other unloaded edge. The mathematical derivations of the formulas required for the construction of the chart are given.
Contributing Partner: UNT Libraries Government Documents Department
Definition of Method of Measurement of Supporting and Control Surface Areas, Special Report

Definition of Method of Measurement of Supporting and Control Surface Areas, Special Report

Date: May 1, 1931
Creator: unknown
Description: Definitions of methods of measurements of supporting and control surface areas are presented. Methods for measuring the supporting surface, i.e., the wing area, and the control surfaces, i.e., the horizontal tail area, the vertical tail area, and the trailing control surface areas are defined. Illustrations of each of the areas are included.
Contributing Partner: UNT Libraries Government Documents Department
Determination of Flight Paths of an SBD-1 Airplane in Simulated Diving Attacks, Special Report

Determination of Flight Paths of an SBD-1 Airplane in Simulated Diving Attacks, Special Report

Date: March 1, 1943
Creator: Johnson, Harold I.
Description: An investigation has been made to determine the motions of and the flight paths describe by a Navy dive-bombing airplane in simulated diving attacks. The data necessary to evaluate these items, with the exception of the atmospheric wind data, were obtained from automatic recording instruments installed entirely within the airplane. The atmospheric wind data were obtained from the ground by the balloon-theodolite method. The results of typical dives at various dive angles are presented in the form of time histories of the motion of the airplane as well as flight paths calculated with respect to still air and with respect to the ground.
Contributing Partner: UNT Libraries Government Documents Department
Drag and Propulsive Characteristics of Air-Cooled Engine-Nacelle Installations for Large Airplanes, Special Report

Drag and Propulsive Characteristics of Air-Cooled Engine-Nacelle Installations for Large Airplanes, Special Report

Date: August 1, 1939
Creator: Silverstein, Abe & Wilson, Herbert A., Jr.
Description: An investigation is in progress in the NACA full-scale wind tunnel to determine the drag and propulsive efficiency of nacelle sizes. In contrast with the usual tests with a single nacelle, these tests were conducted with nacelle-propeller installations on a large model of a 4-engine airplane. Data are presented on the first part of the investigation, covering seven nacelle arrangements with nacelle diameters from 0.53 to 1.5 times the wing thickness. These ratios are similar to those occurring on airplane weighing from about 20 to 100 tons. The results show that the drag, the propulsive efficiency, and the overall efficiency of the various nacelle arrangements as functions of the nacelle size, the propeller position, and the airplane lift coefficient. The effect of the nacelles on the aerodynamic characteristics of the model are shown for both propeller-removed and propeller-operating conditions.
Contributing Partner: UNT Libraries Government Documents Department
Drag of Several Gunner's Enclosures at High Speeds, Special Report

Drag of Several Gunner's Enclosures at High Speeds, Special Report

Date: July 1, 1941
Creator: Stack, John & Moberg, Richard J.
Description: The drag of several types of gunner's turrets, windshields, blisters, and other protuberances, including projecting guns, was investigated at speeds from 75 to 440 miles per hour in the NACA 8-foot high-speed wind tunnel. The various gunner's enclosures were represented by 1/10 and 1/7 full-size models on a midwing-fuselage combination representative of bomber types. Most of the usual types of retractable turrets are very poor aerodynamically; they caused wind drag increments, dependent upon the size of the turret relative to the fuselage and upon the speed, up to twice the drag of the fuselage alone. A large streamline blister sufficient to enclose completely one type of rotating cylindrical turret caused a drag increment of approximately one-half that of the turret and at the same time provided space adequate for two gunners rather than for one gunner. A large portion of the drag increments for some types of turret appeared to be due to adverse effects on the fuselage flow caused by the turret rather than by the direct drag of the turret.
Contributing Partner: UNT Libraries Government Documents Department
The Effect of Compressibility on the Growth of the Laminar Boundary Layer on Low-Drag Wings and Bodies

The Effect of Compressibility on the Growth of the Laminar Boundary Layer on Low-Drag Wings and Bodies

Date: January 1, 1943
Creator: Allen, H. Julian & Nitzberg, Gerald E.
Description: The development of the laminar boundary layer in a compressible fluid is considered. Formulas are given for determining the boundary-layer thickness and the ratio of the boundary-layer Reynolds number to the body Reynolds number for airfoils and bodies of revolution. It i s shown that the effect of compressibility will profoundly alter the Reynolds number corresponding to the upper limit of the range of the low-drag coefficients . The available data indicate that for low-drag and high critical compressibility speed airfoils and bodies of revolution, this effect is favorable.
Contributing Partner: UNT Libraries Government Documents Department
The Effect of Initial Displacement of the Center Support on the Buckling of a Column Continuous over Three Supports

The Effect of Initial Displacement of the Center Support on the Buckling of a Column Continuous over Three Supports

Date: November 1, 1940
Creator: Lunquist, Eugene E. & Kotanchik, Joseph N.
Description: The test indicate that "an indiscriminate single application of the Southwell method (for analyzing Exp. Observations in problems of elastic stability)--can result in definite and measurable errors" The test also indicate "that the effect of curvature due to bending on the critical load for the compression flange material of a box beam is probably small and can be neglected." We have not found this to be true in our tests. It is believed that the effect of curvature, together with a small amount of fixity at the ribs, tends to force the stiffeners to bow in each bay thus effectively increasing their end fixity and thereby raising their allowable loads.
Contributing Partner: UNT Libraries Government Documents Department
The Effect of Lateral Inclination of the Thrust Axis and of Sweepback of the Leading Edge of the Wing on Propulsive and Net Efficiencies of a Wing-Nacelle-Propeller Combination

The Effect of Lateral Inclination of the Thrust Axis and of Sweepback of the Leading Edge of the Wing on Propulsive and Net Efficiencies of a Wing-Nacelle-Propeller Combination

Date: April 1, 1935
Creator: Wood, Donald H. & Windler, Ray
Description: This report describes and gives the results of tests made to determine the effect of lateral inclination of the propeller thrust axis to the direction of flight. A wing-nacelle-propeller combination with the nacelle axis located successively parallel to and at 15 degrees to the perpendicular to the leading edge of a wing was tested with the combination at several angles of yaw. Tests of the wing alone at the same angles of yaw were also made. The data are presented in the usual graphic form. An increase in propulsive efficiency with increase in angle of the thrust axis was found. The change in net efficiency, found by charging the whole nacelle drag to the power unit, was negligible, however, within the range of the tests.
Contributing Partner: UNT Libraries Government Documents Department
The Effect of Streamlining the Afterbody of an N.A.C.A. Cowling

The Effect of Streamlining the Afterbody of an N.A.C.A. Cowling

Date: December 1, 1939
Creator: Stickle, George W.; Crigler, John L. & Naiman, Irven
Description: The drag and the power cost associated with the changing of the nose of a nacelle from a streamline shape to a conventional N.A.C.A. cowling shape was investigated in the N.A.C.A. 20-foot tunnel. Full-scale propellers and nacelles were used. The increment of drag associated with the change of nose shapes was found to be critically dependent on the afterbody of the nacelle. Two streamline afterbodies were tested. The results fo the tests with the more streamlined afterbody showed that the added drag due to the open-nose cowling was only one-fourth of the drag increase obtained with the other afterbody. The results of this research indicate that the power cost, in excess of that with a streamline nose, of using an N.A.C.A. cowling in front of a well-designed afterbody to enclose a 1,500-horsepower engine in an airplane with a speed of 300 miles per hour amounts to 1.5 percent of the engine power. If the open-nose cowling is credited with 1 percent because it cools the front of the cylinders, the non-useful power cost amounts to only 0.5 percent of the engine power.
Contributing Partner: UNT Libraries Government Documents Department
The Effect of Surface Irregularities on Wing Drag, 3, Roughness

The Effect of Surface Irregularities on Wing Drag, 3, Roughness

Date: February 1, 1938
Creator: Hood, Manley J.
Description: Tests have been made in the N.A.C.A. 8-foot high-speed wind tunnel of the drag caused by roughness on the surface of an airfoil of N.A.C.A. 23012 section and 5-foot chord. The tests were made at speeds from 80 t o 500 miles per hour at lift coefficients from 0 to 0.30. For conditions corresponding to high-speed flight, the increase in the drag was 30 percent of the profile drag of the smooth airfoil for the roughness produced by spray painting and 63 percent for the roughness produced. by 0.0037-inch carborundum grains. About one-half the drag increase was caused by the roughness on the forward one-fourth of the airfoil. Sandpapering the painted surface with No. 400 sandpaper made it sufficiently smooth that the drag was no greater than when the surface was polished. In the lower part of the range investigated the drag due to roughness increased rapidly with Reynolds Number.
Contributing Partner: UNT Libraries Government Documents Department
The Effect of Surface Irregularities on Wing Drag. I. Rivets and Spot Welds, 1, Rivets and Spot Welds

The Effect of Surface Irregularities on Wing Drag. I. Rivets and Spot Welds, 1, Rivets and Spot Welds

Date: February 1, 1938
Creator: Hood, Manley J.
Description: Tests have been conducted in the NACA 8-foot high-speed wind tunnel to determine the effect of exposed rivet heads and spot welds on wing drag. Most of the tests were made with an airfoil of 5-foot chord. The air speed was varied from 80 to 500 miles per hour and the lift coefficient from 0 to 0.30. The increases in the drag of the 5-foot airfoil varied from 6%, due to countersunk rivets, to 27%, due to 3/32-inch brazier-head rivets, with the rivets in a representative arrangement. The drag increases caused by protruding rivet heads were roughly proportional to the height of the heads. With the front row of rivets well forward, changes in spanwise pitch had negligible effects on drag unless the pitch was more than 2.5% of the chord. Data are presented for evaluating the drag reduction attained by removing rivets from the forward part of the wing surface; for example, it is shown that over 70% of the rivet drag is caused by the rivets on the forward 30% of the airfoil in a typical case.
Contributing Partner: UNT Libraries Government Documents Department
The Effect of Surface Irregularities on Wing Drag. II - Lap Joints, 2, Lap Joints

The Effect of Surface Irregularities on Wing Drag. II - Lap Joints, 2, Lap Joints

Date: February 1, 1938
Creator: Hood, Manley J.
Description: Tests have been made in the NACA 8-foot high-speed wind tunnel of the drag caused by four types of lap joint. The tests were made on an airfoil of NACA 23012 section and 5-foot chord and covered in a range of speeds from 80 to 500 miles per hour and lift coefficients from 0 to 0.30. The increases in profile drag caused by representative arrangements of laps varied from 4 to 9%. When there were protruding rivet heads on the surface, the addition of laps increased the drag only slightly. Laps on the forward part of a wing increased the drag considerably more than those farther back.
Contributing Partner: UNT Libraries Government Documents Department
FIRST PREV 1 2 3 4 5 NEXT LAST