Search Results

open access

Mechanical Properties of Zirconium and Zirconium-Uranium Alloys Containing Tin

Description: Abstract: "The mechanical properties of a large number of zirconium alloys have been investigated. These alloys include zirconium-tin and zirconium-tin-uranium. Tensile tests have been run on these alloys at room temperature, 500 F, and 600 F. Hot-hardness data have been obtained from room temperature to 1600 F, with particular emphasis on the hot-rolling range. Creep tests and fatigue tests have been run on a number of zirconium-tin alloys at 500 F."
Date: September 29, 1952
Creator: Schwope, A. D.; Muehlenkamp, G. T. & Chubb, Walston
Partner: UNT Libraries Government Documents Department
open access

Mechanical Properties of Zirconium and Zirconium-Uranium Alloys Containing Tin

Description: Abstract: "The mechanical properties of a large number of zirconium alloys have been investigated. These alloys include zirconium-tin and zirconium-tin-uranium. Tensile tests have been run on these alloys at room temperature, 500 F, and 600 F. Hot-hardness data have been obtained from room temperature to 1600 F, with particular emphasis on the hot-rolling range. Creep tests and fatigue tests have been run on a number of zirconium-tin alloys at 500 F."
Date: September 29, 1952
Creator: Schwope, A. D.; Muehlenkamp, G. T. & Chubb, Walston
Partner: UNT Libraries Government Documents Department
open access

Mechanical Properties of Iodide Zirconium Alloys

Description: Introduction: "The tensile properties, hot hardness, impact strength; and corrosion resistance of some arc-melted, iodide zirconium alloys have been determined. The alloys investigated include binary alloys of zirconium containing zero to five per cent tin, binary alloys of zirconium containing zero to 0.14 per cent nitrogen, and ternary alloys of zirconium containing tin and nitrogen, tin and uranium, and uranium and beryllium."
Date: November 1, 1952
Creator: Schwope, A. D. & Chubb, Walston
Partner: UNT Libraries Government Documents Department
open access

The Preparation of Beta Silicon Carbide

Description: This report explores the production of beta silicon carbide, a low-temperature, cubic modification of cubic silicon carbide. The temperature, heating time, type of starting material, and proportion of starting materials were all varied in order to test yields of beta silicon carbide.
Date: December 29, 1952
Creator: Gambino, J. R.; Mixer, W. G., Jr.; Wagner, H. E. & Harman, Cameron G.
Partner: UNT Libraries Government Documents Department
open access

Evaluation of Oxidation-Resistant Ceramics for High-Temperature Reactor Elements

Description: Abstract: "As a possible aid in the selection of ceramic materials for use in the fabrication of high-temperature reactor elements, the reported properties of 23 refractory oxidation-resistance ceramic compounds are tabulated. The thermal stresses and heat throughout capacities for nine of these compounds are estimated for conditions of steady heat flow and uniform heat generation in the temperature range of 1500 to 2500 F. The compounds studied have macroscopic thermal-neutron-absorption cross… more
Date: December 1, 1952
Creator: Harman, Cameron G.; Ferrell, Edward Francis.; Wagner, H. E. & Quirk, J. F.
Partner: UNT Libraries Government Documents Department
open access

Mechanical Properties of Zirconium-Tin Alloys

Description: Abstract: "The mechanical properties and corrosion resistance of induction-melted, zirconium-tin alloys have been determined. The alloys investigated contained from zero to five per cent tin and up to 0.3% carbon. The zirconium used was United States Bureau of Mines sponge zirconium. The mechanical properties investigated include the tensile, hot-hardness, and impact properties."
Date: December 22, 1952
Creator: Schwope, A. D. & Chubb, Walston
Partner: UNT Libraries Government Documents Department
open access

The Rolling of Uranium

Description: The following report discusses the method of rolling uranium rods and strips under various rolling conditions and the roll-separating force measured.
Date: December 30, 1952
Creator: Saller, Henry A.; Keeler, J. R. & Donley, R. J.
Partner: UNT Libraries Government Documents Department
open access

Electroplates on Thorium

Description: Abstract: "The protection of thorium in hot water was studied. Copper electrocladding on thorium offers promising protection against hot water. The corrosion of thorium in 95 C water was reduced appreciably by a thorium phosphate film. The results of this abbreviated investigation offer a basis for the development of a method of protecting thorium at elevated temperatures in corrosive media."
Date: January 9, 1953
Creator: Beach, John G.; Schickner, W. C.; Vaaler, L. E. & Faust, Charles L.
Partner: UNT Libraries Government Documents Department
open access

The Fabrication of Thorium Tubes

Description: Abstract: "Thorium tubes were cold drawn from extruded tube stock and also from drilled hot-rolled rod. Total reductions up to approximately 85 per cent were accomplished by conventional tube-drawing methods, without an intermediate anneal. The hard-drawn tubes had high tensile strength, but the ductility, as indicated by flaring and flattening tests, was low."
Date: January 16, 1953
Creator: Saller, Henry A. & Keeler, J. R.
Partner: UNT Libraries Government Documents Department
open access

Protective Coatings for Molybdenum

Description: Report discussing studies on various types of protective coatings for a molybdenum sheet. Procedures, materials, and results of each coating are included.
Date: February 17, 1953
Creator: Powell, Carroll F.; Jones, R. P.; Secrest, A. C.; Sherwood, E. M. & Campbell, Ivor E.
Partner: UNT Libraries Government Documents Department
open access

Creep Strength of Uranium Alloys at 1500 and 1800 F

Description: Abstract:"The creep resistance of various uranium binary alloys was investigated at 1500 and 1800 F in vacuum. Tests were made on alloys of uranium with beryllium, columbium, molybdenum, tantalum, titanium, and zirconium and on molybdenum-UO2 composites. Of the alloys examined, those of the uranium-molybdenum system exhibited the best creep resistance. At 1500 F, creep rates of about 0.005%/hr were produced in uranium-molybdenum alloys by a stress of 2500 psi and, at 1800 F, similar creep rates… more
Date: May 28, 1953
Creator: Saller, Henry A.; Stacy, J. T.; Eddy, N. S. & Klebanow, H. L.
Partner: UNT Libraries Government Documents Department
open access

The Solubility of Oxygen in Uranyl Sulphate Solutions at Elevated Temperatures

Description: Abstract: "The solubility of oxygen in uranyl sulphate solutions and in water at 212, 275, and 325 F, and at oxygen partial pressures up to 1500 psia was investigated. The results are presented in tabular and graphic form. The solubility is proportional to the partial pressure of oxygen. The ratio of solubility in the uranyl sulphate solution to solubility in water at the same temperature and pressure is a function of the concentration of the salt in solution."
Date: June 10, 1953
Creator: Pray, H. A. & Stephan, Elmer F.
Partner: UNT Libraries Government Documents Department
open access

The Ductility of Brazed Stainless Steel Joints

Description: Abstract: "The ductility of Type 310 stainless steel T-joints brazed with GE-62 brazing alloy was measured at room temperatures 1200, 1650, and 1800 F. The measure of ductility was taken as the plastic axial strain required to crack braze fillets in T-section tensile specimens. At elevated temperatures, the ductility of as-brazed joints approximated that of the stainless steel, but at room temperature the brazed joints had only one-tenth the ductility of the base metal. Annealing for 16 hr at 1… more
Date: July 8, 1953
Creator: Saller, Henry A.; Stacy, J. T. & Eddy, N. S.
Partner: UNT Libraries Government Documents Department
open access

Extrusion Cladding of Fuel Element

Description: From introduction: "This investigation was undertaken with the general objective of determining whether uranium core could be sheathed with aluminum by an extrusion-cladding process. The ultimate objective of this work was to determine the feasibility of extrusion cladding flat plates of uranium."
Date: March 22, 1955
Creator: Slunder, C. J.; Fiorentino, R. J. & Hall, A. M.
Partner: UNT Libraries Government Documents Department
open access

Electrodeposition of Aluminum on Uranium

Description: Abstract: "Aluminum electroplating was studied in a search for new methods of cladding uranium fuel elements. Uranium electroclad with 12 mils of aluminum over a 0.5-mil (or nickel plus copper) electroplate resisted corrosion for more than 100 hr in boiling water. This quality of protection was effected by hot pressing the electroclad uranium with 5.1 tons per sq in. for 5 min at 950 F. The electroclad uranium with hot-pressed samples paralleled those of later experiments with hot-pressed wroug… more
Date: March 30, 1955
Creator: Beach, John G.; Schickner, William C.; Hopkinson, Dolores. & Faust, Charles L.
Partner: UNT Libraries Government Documents Department
open access

Electroplated Metals on Uranium for Aluminum Cladding

Description: Abstract: "Aluminum-clad nickel-plated uranium is corrosion resistant in boiling water. Samples with intentional defects in the aluminum-nickel clodding layers, after testing for more than 300 hr. showed no sign of rapid failure. The study of electroplated metals on uranium for aluminum cladding has defined the effects of several processing variables on the corrosion resistance. The quality of the uranium and the quality of the aluminum-nickel bond were important. Heat treatment and vacuum outg… more
Date: May 4, 1955
Creator: Beach, John G.; Schickner, William C.; Hopkinson, Dolores. & Faust, Charles L.
Partner: UNT Libraries Government Documents Department
open access

Apparatus for visual study of corrosion by hot water

Description: Report describing an apparatus for visual study of corrosion of uranium by hot water. A windowed autoclave was designed and constructed to permit visual study of the reaction under conditions simulating a cladding failure in service.
Date: 1955
Creator: Grieser, Daniel R. & Simons, Eugene M.
Partner: UNT Libraries Government Documents Department
open access

Grain Refinement of the As-Cast Uranium-5 w/o Chromium Alloy by Heat Treatment

Description: Introduction: "The uranium-5 w/o chromium alloy has been intensively investigated for use in a power reactor in the as-cast condition. However, when cast sample fuel elements were subjected to irradiation, their stability was found to be unsatisfactory. In order to improve the behavior of the alloy, a program of grain refinement by heat treatment was begun. The effect of chill casting on the heat-treated grain size was also investigated."
Date: May 13, 1955
Creator: Saller, Henry A.; Rough, Frank A. & Bauer, Arthur A.
Partner: UNT Libraries Government Documents Department
open access

Low-Melting Alloys for Cast Fuel Elements

Description: The following report follows an investigation made to determine the composition of uranium-rich ternary eutectic alloys most suitable for reactor application in the as-cast condition. These determinations were made based metallographic examination and thermal analysis of as-cast alloys.
Date: May 19, 1955
Creator: Saller, Henry A.; Rough, Frank A. & Bauer, Arthur A.
Partner: UNT Libraries Government Documents Department
open access

Ceramic Investigations of UO₂

Description: This report covers the progress made on an intensive program to develop and evaluate UO2 as a possible fuel element for the PWR.
Date: June 16, 1955
Creator: Allison, Adrian G. & Duckworth, Winston H.
Partner: UNT Libraries Government Documents Department
open access

Annealing of crystal distortion in irradiated graphite

Description: From introduction: "As part of the program for improvement of graphite, the structural characteristics of graphite have been studied to determine the relation between physical and structural changes during irradiation."
Date: 1955
Creator: Austin, Alfred E. & Harrison, Ralph J.
Partner: UNT Libraries Government Documents Department
Back to Top of Screen