Technical Report Archive & Image Library (TRAIL) - 39 Matching Results

Search Results

Results: 1 - 24 next
open access

Tanks test of a model of the hull of the Navy PB-1 flying boat - N.A.C.A. Model 52

Description: A model of the hull of the Navy PB-1 flying boat was tested in the N.A.C.A. tank as part of a program intended to provide information regarding the water performance of hulls of flying boats of earlier design for which hydrodynamic data have heretofore been unavailable. Tests were made according to the general method over the range of practical loadings with the model both fixed in trim and free to trim. A free-to-trim test according to the specific method was also made for the design load and … more
Date: August 1936
Creator: Allison, John M.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Tank tests of models of flying boat hulls having longitudinal steps

Description: Four models with longitudinal steps on the forebody were developed by modification of a model of a conventional hull and were tested in the National Advisory Committee for Aeronautics (NACA) tank. Models with longitudinal steps were found to have smaller resistance at high speed and greater resistance at low speed than the parent model that had the same afterbody but a conventional V-section forebody. The models with a single longitudinal step had better performance at hump speed and as low hig… more
Date: July 1936
Creator: Allison, John M. & Ward, Kenneth E.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Tank Tests of a Model of the NC Flying-Boat Hull - N.A.C.A. Model 44

Description: "A 1/7.06 full-size model of the NC-type hull was tested in the N.A.C.A. tank by both the general method and the specific or free-to-trim method. The results of the tests are given in curves plotted as non dimensional coefficients and are compared with the test results of N.A.C.A. model 11-A. The NC model (N.A.C.A. model 44) shows higher resistance than model 11-A at hump speed but lower resistance at high speeds. Model 44 has a higher best trim angle at the jump and a lower maximum positive tr… more
Date: May 1936
Creator: Bell, Joe W.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Combustion-engine temperatures by the sodium line-reversal method

Description: The sodium line-reversal method has been used in some preliminary measurements of flame temperature. Improvements in the method involving a photographic recorder and a means of correcting for the dirtiness of the windows are described. The temperatures so obtained are compared with those calculated from pressure diagrams.
Date: March 1936
Creator: Brevoort, Maurice J.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Mechanical Properties of Aluminum-Alloy Rivets

Description: "The development of metal construction for aircraft has created a need for accurate and detailed information regarding the strength of riveted joints in aluminum-alloy structures. To obtain this information the National Bureau of Standards in cooperation with the National Advisory Committee for Aeronautics is investigating the strength of riveted joints in aluminum alloys. The strength of riveted joints may be influenced by the form of the head, the ratio of the rivet diameter to the sheet thic… more
Date: November 1936
Creator: Brueggeman, W. C.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Tank tests of three models of flying-boat hulls of the pointed-step type with different angles of dead rise - NACA model 35 series

Description: From Summary: "The results of tank tests of three models of flying-boat hulls of the pointed-step type with different angles of dead rise are given in charts and are compared with results from tests of more conventional hulls. Increasing the angle of dead rise from 15 to 25 degrees: had little effect on the hump resistance; increased the resistance throughout the planning range; increased the best trim angle; reduced the maximum positive trimming moment required to obtain best trim angle; and h… more
Date: January 1936
Creator: Dawson, John R.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

A general tank test of a model of the hull of the British Singapore IIC flying boat

Description: A general test was made in the N.A.C.A. tank of a 1/12-size model of the hull of the British Singapore IIC flying boat loaned by the Director of Research, British Air Ministry. The results are given in charts and are compared with the results of tests of a model of an American flying-boat hull, the Sikorsky S-40. The Singapore hull has a greater hump resistance but a much lower high-speed resistance than the S-40.
Date: September 1936
Creator: Dawson, John R. & Truscott, Starr
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Full-scale wind-tunnel and flight tests of a Fairchild 22 airplane equipped with a Fowler flap

Description: "Full-scale wind-tunnel and flight tests were made of a Fairchild 22 airplane equipped with a Fowler flap to determine the effect of the flap on the performance and control characteristics of the airplane. In the wind-tunnel tests of the airplane with the horizontal tail surfaces removed, the flap was found to increase the maximum lift coefficient from 1.27 to 2.41. In the flight test, the flap was found to decrease the minimum speed from 58.8 to 44.4 miles per hour" (p. 1).
Date: August 1936
Creator: Dearborn, C. H. & Soulé, H. A.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

The Forces and Moments on Airplane Engine Mounts

Description: "A resume of the equations and formulas for the forces and moments on an aircraft-engine mount is presented. In addition, available experimental data have been included to permit the computation of these forces and moments. A sample calculation is made and compared with present design conditions for engine mounts" (p. 1).
Date: December 1936
Creator: Donely, Philip
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Influence of Fuel-Oil Temperature on the Combustion in a Prechamber Compression-Ignition Engine

Description: Note presenting the influence of fuel-oil temperature on combustion as investigated by injecting the fuel into the prechamber of a single-cylinder, 4-stroke-cycle, water-cooled, compression-ignition engine operating at 1500 rpm and at a compression ratio of 13.5. The results showed that heating the fuel oil to 750 degrees Fahrenheit increased the injection period, changed the rate of injection, and eliminated the spray cone.
Date: April 1936
Creator: Gerrish, Harold C. & Ayer, Bruce E.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Mixture Distribution in a Single-Row Radial Engine

Description: "The distribution of the fuel among the various cylinders of a Pratt and Whitney 1340 S1H1-G engine was determined by chemically analyzing samples of exhaust gas from each cylinder. The engine was operated in the 20-foot wind tunnel at different power outputs, specific fuel consumptions, and engine speeds. The results showed that the variation in the quality of the mixture among the different cylinders was approximately 4 percent and was independent of power output, specific fuel consumption, a… more
Date: October 1936
Creator: Gerrish, Harold C. & Voss, Fred
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Limitations of the Pilot in Applying Forces to Airplane Controls

Description: Measurements were made to determine the relative maximum forces a pilot can exert on the controls of an airplane with the view of obtaining systematic data upon which to base the location of controls within the cockpit and the design of the control surfaces. A cockpit model of generous proportions, capable of being rotated to any attitude, was built with the location of the control stick and rudder pedals adjustable over a wide range of positions with respect to the seat. Besides measurements o… more
Date: January 1936
Creator: Gough, M. N. & Beard, A. P.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Notes on the technique of landing airplanes equipped with wing flaps

Description: "The proper landing of airplanes equipped with flaps, although probably no more difficult than landing without them, requires a different technique. The effects of flaps on the aerodynamics characteristics of a wing are given and, with the aid of figures and diagrams, a detailed comparison of the glide and landing of an airplane with and without flaps is made. The dangers attending improper execution and the importance of such factors as air speed fuselage attitude, glide-path angle, and contro… more
Date: January 1936
Creator: Gough, Melvin N.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Considerations of the Take-Off Problem

Description: Many technical papers on the various phases of airplane take-off have been published. Frequently, however, there appear new ideas which affect only particular scattered phases of the subject and which do not receive individual publication. It is the purpose of this paper to present several ideas of this nature which may be of considerable aid in calculating take-off performance and one idea which should correct what appears to be a popular misconception of the importance of static propeller thr… more
Date: February 1936
Creator: Hartman, Edwin P.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Tests of N.A.C.A. airfoils in the variable-density wind tunnel. Series 230

Description: The results of tests of six airfoils having the N.A.C.A. 230 mean line and varying in thickness from 0.06c to 0.21c are presented. These results agree with previous findings in showing that aerodynamically the best section is one of moderate thickness. The data are of value mainly in connection with the design of tapered wings having sections based on the N.A.C.A. 230 mean line.
Date: May 1936
Creator: Jacobs, Eastman N. & Pinkerton, Robert M.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

The reduction of aileron operating force by differential linkage

Description: "It is shown that the control force of ordinary ailerons may be reduced to zero over a range of deflections and at a given flight condition by the use of an appropriate differential movement. Approximations to the ideal motion obtainable with a simple linkage are discussed and a chart that enables the selection of an appropriate crank arrangement is presented. Various aspects of the practical application of the system are discussed and it is concluded that a small fixed tab, deflected to trim b… more
Date: December 1936
Creator: Jones, Robert T. & Nerken, Albert I.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Circular Motion of Bodies of Revolution

Description: The circular motion for airship-like bodies has thus far been calculated only for a prolate ellipsoid of revolution (reference 1, p.133 and reference 2). In this paper, however, the circular motion of elongated bodies of revolution more nearly resembling airships will be investigated. The results will give the effect of rotation on the pressure distribution and thus yield some information as to the stresses set up in an airship in circular flight.
Date: February 1936
Creator: Kaplan, Carl
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Estimation of moments of inertia of airplanes from design data

Description: "A method of determining the moments of inertia of an airplane from design data pertaining to the weights and locations of the component parts is described. The computations required to ascertain the center-of-gravity position are incorporated with the calculations of moments of inertia. A complete set of data and calculations for a modern airplane is given to illustrate the procedure. From a comparison between calculated values and measured values it is believed that the moments of inertia can… more
Date: July 1936
Creator: Kirschbaum, H. W.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Further Measurements of Normal Accelerations on Racing Airplanes

Description: This report details the acceleration data collected from racing airplanes during actual races. The data was collected in order to make recommendations regarding the structural safety of racing airplanes and the methods of operating racing airplanes that reduces the probability of subjecting them to extreme air loads. The records do not lead to any conclusions regarding maximum air loads.
Date: February 1936
Creator: Kirschbaum, H. W. & Scudder, N. F.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Remarks on the Elastic Axis of Shell Wings

Description: The definitions of flexural center, torsional center, elastic center, and elastic axis are discussed. The calculation of elastic centers is dealt with in principle and a suggestion is made for the design of shear webs.
Date: April 1936
Creator: Kuhn, Paul
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Piloting technique for recovery from spins

Description: "Systematic flight investigation of the spinning characteristics of various airplanes over a period of several years have given the pilots engaged in the testing a varied and extensive experience. From this experience certain general rules of procedure have been formulated, particularly for the sequence of operation of the controls in recovery from spins, and are recommended to the attention of all pilots" (p. 1).
Date: February 1936
Creator: McAvoy, W. H.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Friction of compression-ignition engines

Description: "The cost in mean effective pressure of generating air flow in the combustion chambers of single-cylinder compression-ignition engines was determined for the prechamber and the displaced-piston types of combustion chamber. For each type a wide range of air-flow quantities, speeds, and boost pressures was investigated. Supplementary tests were made to determine the effect of lubricating-oil temperature, cooling-water temperature, and compression ratio on the friction mean effective pressure of t… more
Date: August 1936
Creator: Moore, Charles S. & Collins, John H., Jr.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Boosted Performance of a Compression-Ignition Engine With a Displaced Piston

Description: From Summary: "Performance tests were made using a rectangular displacer arranged so that the combustion air was forced through equal passages at either end of the displacer into the vertical-disk combustion chamber of a single-cylinder, four-stroke-cycle compression-ignition test engine. After making tests to determine optimum displacer height, shape, and fuel-spray arrangement, engine-performance tests were made at 1,500 and 2,000 r.p.m. for a range of boost pressures from 0 to 20 inches of m… more
Date: May 1936
Creator: Moore, Charles S. & Foster, Hampton H.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Tank tests of models of floats for single-float seaplanes - First series

Description: "Large models of the Mark V and Mark VI floats used for single float seaplanes (National Advisory Committee for Aeronautics (NACA) models 41-A and 41-B, respectively) were tested in the NACA tank to provide general test data for typical single floats and a basis for possible improvements of their form. The resistance of model 41-B was greater than that of model 41-A, either when free to trim or at the best trim angle for each. The resistance of model 35-B (a pointed step hull tested free to tri… more
Date: April 1936
Creator: Parkinson, J. B.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
Back to Top of Screen