National Advisory Committee for Aeronautics (NACA) - 119 Matching Results

Search Results

Results: 1 - 24 next
open access

Additional design charts relating to the stalling of tapered wings

Description: From Introduction: "The present report, therefore, may be considered a supplement to reference 1. The combined scope of the stall charts of reference 1, designated A, and of the present work, designated B, is summarized in the following table: For the wing with root thickness ratio to 18 was also investigated.
Date: January 1943
Creator: Harmon, Sidney M.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Aerodynamic and Hydrodynamic Tests of a Family of Models of Flying-Boat Hulls Derived From a Streamline Body: NACA Model 84 Series

Description: Report presenting a series of related flying-boat hull forms with various combinations of aerodynamic and hydrodynamic requirements that were tested in an NACA tank and high-speed tunnel. Effects explored included varying the height of the bow, varying the height of the stern, increasing the angle of dead rise at the bow, decreasing the angle of dead rise on the afterbody, increasing the depth of step, increasing the angle of afterbody keel, adding chine flare, adding a third planing surface, a… more
Date: September 1943
Creator: Parkinson, John B.; Olson, Roland E.; Draley, Eugene C. & Luoma, Arvo A.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Altitude Rating of Electrical Apparatus

Description: "This paper studies the effect of altitude on the ratings of rotating electric machines and after determining the fundamental principles involved, discusses these in relation to the application of such machines in modern aircraft" (p. 1).
Date: January 1943
Creator: Lebenbaum, Paul, Jr.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

The Analysis of Strains Indicated by Multiple-Strand Resistance-Type Wire Strain Gages Used as Rosettes

Description: "Methods are given for making the necessary corrections to the strains indicated by multiple-strand resistance-type wire strain gages used singly or as rosettes to measure strains at an angle to the principal strain. The results of tests to determine the validity of the methods of correction are reported" (p. 1).
Date: January 1943
Creator: Dow, Norris F.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Analysis of Wind-Tunnel Stability and Control Tests in Terms of Flying Qualities in Full-Scale Airplanes

Description: From Summary: "The analysis of results of wind-tunnel stability and control tests of powered airplane models in terms of the flying qualities of full-scale airplanes is advocated. In order to indicate the topics upon which comments are considered desirable in the report of a wind-tunnel stability and control investigation and to demonstrate the nature of the suggested analysis, the present NACA flying-qualities requirements are discussed in relation to wind-tunnel tests. General procedures for … more
Date: October 1943
Creator: Kayten, Gerald G.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Charts for calculation of the critical stress for local instability of columns with I-, Z-, channel and rectangular-tube section

Description: Report presenting charts for the calculation of the critical stress for local instability of columns with I-, Z-, channel-, and rectangular-tube sections. An experimental curve is included for use in taking into account the effect of stresses above the elastic range on 24S-T aluminum alloy elasticity.
Date: November 1943
Creator: Kroll, W. D.; Fisher, Gordon P. & Heimerl, George J.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

A Comparative Study of the Effect of Wing Flutter Shape on the Critical Flutter Speed

Description: Report presenting a comparison of the results of calculations of the critical flutter speeds of nine uniform rectangular wings without ailerons by two methods: one in which the effect of the wing flutter shape is introduced indirectly by choosing mean values for the wing parameters and one that introduces an additional degree of freedom in the wing-bending flutter mode.
Date: November 1943
Creator: Pinkel, I. Irving
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Comparison of various methods for computing drag from wake surveys

Description: "The various equations for computing profile drag by the momentum method are examined, and the errors arising from complete or partial neglect of compressibility effects in the Jones equation and the Bicknell equation are evaluated. The integrating method of Silverstein and Katzoff is shown to be accurate over a wide range of Mach number and wake shapes" (p. 1).
Date: January 1943
Creator: Davis, Wallace F.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Construction of Wire Strain Gages for Engine Application

Description: Report presenting instructions for winding, baking, and mounting a phanolic resin-impregnated, bobbin-type wire strain gage that consists of Advance wire wound around a paper form. A description of some test equipment useful for establishing the merits of the techniques used in gage construction has been included.
Date: December 1943
Creator: Nettles, J. Cary & Tucker, Maurice
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Correlation of single-cylinder cooling tests of a Pratt and Whitney R-2800-21 engine cylinder with wind-tunnel tests of a Pratt and Whitney R-2800-27 engine

Description: Report presenting an equation in which it is possible to correlate the cooling characteristics of an engine. Results regarding engine cooling, engine performance, and estimated cooling-pressure-drop requirements are provided.
Date: December 1943
Creator: Ellerbrock, Herman H., Jr.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

A Correlation of the Dimensions, Proportions, and Loadings of Existing Seaplane Floats and Flying Boat Hulls

Description: Report presenting a study to determine what loadings and proportions have been chosen by designers of seaplanes and flying boats and what, if any, interrelations exist between the loadings and proportions. The characteristics considered include the beam, getaway speed, forebody length, afterbody length, hull length, center of gravity, and brake horsepower necessary.
Date: March 1943
Creator: Locke, Fred W. S., Jr.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Critical shear stress of an infinitely long flat plate with equal elastic restraints against rotation along the parallel edges

Description: Report presenting a chart for the values of the coefficient in the formula for the critical shear stress at which buckling may be expected to occur in an infinitely long flat plate with parallel edges. An approximate method for the evaluation of the critical shear stress when the elastic restraints on the two parallel edges are not equal is also presented.
Date: November 1943
Creator: Stowell, Elbridge Z.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Critical stress for an infinitely long flat plate with elastically restrained edges under combined shear and direct stress

Description: "A simple interaction curve is presented for evaluating the conditions of combined shear and direct stress under which an infinitely long, flat plate with equal elastic restraints against rotation along the edges will become unstable. The theoretical work that led to the interaction curve is presented in the form of appendixes" (p. 1).
Date: November 1943
Creator: Stowell, Elbridge Z. & Schwartz, Edward B.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Critical Stresses for Plates

Description: Report presenting the basic methods of theoretically calculating the critical stress for plates with elastically restrained edges. Design charts for various types of sections and columns and critical stress for flat plates and curved sheets are provided.
Date: October 1943
Creator: Lundquist, Eugene E. & Schuette, Evan H.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Design criterions for the dimensions of the forebody of a long-range flying boat

Description: Report presenting a correlation of the gross-load coefficient and the forebody length-beam ratio for a limited number of present-day multiengine long-range flying boats for which the spray characteristics are known. Results indicate that the gross-load coefficient for comparable spray characteristics varies as the square of the forebody length-beam ratio.
Date: November 1943
Creator: Parkinson, John B.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Design, selection, and installation of aircraft heat exchangers

Description: Report presenting a survey of aircraft heat exchangers in three parts: design, selection, and installation. Appendices give the physical properties of air, properties of standard atmosphere as defined by the Navy, Army, and NACA, and an impact-pressure chart.
Date: July 1943
Creator: Wood, George P. & Brevoort, Maurice J.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Determination of the damping moment in yawing for tapered wings with partial-span flaps

Description: Report presenting a method for determining the damping moment in yawing for tapered wings with partial-span flaps. Charts are given for untwisted wings with various taper ratios, aspect ratios, and center-span flaps. Theoretical and experimental results are provided.
Date: August 1943
Creator: Harmon, Sidney M.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Development of thermal ice-prevention equipment for the B-17F airplane

Description: Report presenting a thermal ice-prevention system for the B-17F airplane. The report includes a description of the design, an outline of the design, analysis, and a presentation and discussion of flight-test thermal data secured under non-icing conditions. The basic idea of the design was to raise the temperature of the surfaces to be protected from ice formations by subjecting the inner faces to a stream of heated air.
Date: August 1943
Creator: Jones, Alun R. & Rodert, Lewis A.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Effect of Carburetor-Mixture-Control and Supercharger Characteristics on Fuel Knock Under Simulated Sea-Level Flight Conditions

Description: Report presenting knock-limit data recorded for a current 100-octane-number aviation gasoline in a full-scale single-cylinder test engine. Inlet-air temperatures were the temperatures estimated from a consideration of the temperature increase through an aircraft-engine supercharger. The data indicate that the relation of the carburetor-mixture-control characteristics to the knock characteristics of the fuel is an important factor in determining knock-free operation.
Date: March 1943
Creator: Rothrock, Addison M. & Wear, Jerrold D.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

The effect of compressibility on two-dimensional tunnel-wall interference for a symmetrical airfoil

Description: Summary: The effective change in the velocity of flow past a wing section, caused by the presence of wind-tunnel walls, is known for potential flow. This theory is extended by investigation of the two-dimensional compressible flow past a thin Rankine Oval. It is shown that for a symmetrical section at zero angle of attack the velocity increment due to the tunnel walls in the incompressible case must be multiplied by the factor 1/1-M^2 to take account of compressibility effects. The Mach numb… more
Date: May 1943
Creator: Nitzberg, Gerald E.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

The effect of dead rise upon the high-angle porpoising characteristics of two planing surfaces in tandem

Description: Report presenting porpoising tests of three rudimentary models composed of two V-bottom planing surfaces in tandem and fitted with a tail plane. The upper and lower branches of the upper trim limit of stability were determined for three angles of dead rise and two depths of step.
Date: June 1943
Creator: Benson, James M. & Klein, Milton M.
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
open access

Effect of Length-Beam Ration on Resistance and Spray of Three Models of Flying-Boat Hulls

Description: Report presenting an investigation of the effect of changes in the length-beam ratio of flying-boat hulls on resistance and spray. A family of three models of hulls of different length-beam ratios was used and, in order to maintain comparable hull sizes, the plan-form areas of the hulls were made approximately equal by keeping equal products of length and beam. Results regarding resistance, spray, and take-off performance are provided.
Date: October 1943
Creator: Bell, Joe W.; Garrison, Charlie C. & Zeck, Howard
Item Type: Refine your search to only Report
Partner: UNT Libraries Government Documents Department
Back to Top of Screen