Surface Machinery and Methods for Oil-Well Pumping Page: 58
183 p. : ill.View a full description of this report.
Extracted Text
The following text was automatically extracted from the image on this page using optical character recognition software:
58 SURFACE MACHINERY AND METHODS FOR OIL-WELL PUMPING.
List of mnachnery and material, etc.-Continued.Machinery and material
12
2
2
7
6
2
25
15
10
3
1
1
2
34
26
3
4
3
1
1Refer.
ence
No.Amount
- -I- I
2 by 4 inches by 20 feet, Oregon pine, rough, for
purlins and braces.
2 by 4 inches by 24 feet, Oregon pine, rough, for
plates.
2 by 4 inches by 12 feet, Oregon pine, surfaced one
side, for girts at windows.
1 by 6 inches by 16 feet, Oregon pine, surfaced four
sides, for facings, casings, louver, etc.
2 by 3 inches by 6 feet, Oregon pine, surfaced four
sides, for windows.
1 by 4 inches by 16 feet, Oregon pine, surfaced four
sides, for window trim.
2 feet 6 inches by 2 feet 6 inches, plain mill windows,
6-light.
Pounds 2-inch galvanized roofing nails- ..........-
Pounds 20-d. common wire nails...............----
Pounds 10-d. common wire nails----.......--........-----
Pounds 8-d. common wire nails.......--------..........--
Pound 4-d. common wire nails _ _ ....___-------..
Pound 6-d. finishing nails- .__-_---_ _......-----
Pair 8-inch strap hinges with 1k-inch screws .....
26 by 96 inches, No. 26 gage, corrugated galvan-
ized iron.
-- --do--------------------------------- ...........................................
26 by 84 inches, No. 26 gage, corrugated galvan-
ized iron.
26 by 72 inches, No. 26 gage, corrugated galvan-
ized iron.
Pieces, No. 26 gage, galvanized roll ridge-cap, 10
feet long.
Location sign--------------.....................................--------------
Precaution sign_ .........--------------------------
Nine-foot motor house, used for wells with 10-foot
band wheel, has identical material with those
for 8-foot motor house, used for wells with a 9-
foot band wheel, except items 11, 15 and 30 which
are to be as follows:
4 by 4 inches by 18 feet, Oregon pine, rough-.......
2 by 4 inches by 16 feet, Oregon pine, rough .......
2 by 4 inches by 18 feet, Oregon pine, rough ...__..
26 by 108 inches, No. 26 gage, corrugated galvan-
ized iron.
Countershaft ...._ ____ __ _-----------.............
Grease cup..............................----------------------------
}-inch and 3-inch nipples..-----.....--------------........
k-inch coupling _ _...__------------------ ------
10 inches by 36 feet 6 inches, 4-ply endless rubber
belt.
20-inch countershaft pulley, cast iron .-_----------
40-inch, 48-inch or 60-inch countershaft pulley to_ _
give speed required. When old engine pulley is
used in lieu of 20-inch pulley, the large pulley
must be selected to meet conditions.
Motor, oil well, 30/15-hp., 3-phase, 60-cycle, 440-
volt, two-speed variable, complete, with 12-inch
diameter by 10-inch paper pulley and pole
changing switch with cover.Classification
8-foot motor house. _
.....do_--------------
.....do-----------
.....do....----------
.....do....-------------
.....do--------------
.....do----
.....do..............----------
-... do...
.....do....-------
-- --do-------------
--.....do---.....-------
.... do--...--------
. _- do .............
.....do....----------
.....do--------------..............
-- - do ....----------
.....do ..------------
....-do ............
....do
.....do...---------
.....do --------------
9-foot motor house...
.....do---- ............-----
.....o.............-----
.....do--............--------
Power equipment-
mechanical.
.-- -- do-------..
-..... do ----------
--..-- do
...do ....---------
.....do----------
Sdo__---------
Power equipment-
electrical.Plate No.
X, B.
Do.
Do.
X, B.
Do.
Do.
Do.
Do.
X, C.
Do.
X, B.
Do.
Do.
Do.
X, E.
X, F.
Do.
X, E.
Do.
Do.
Do.11
15
30
37
38
39
40
41
42
43
44
Upcoming Pages
Here’s what’s next.
Search Inside
This report can be searched. Note: Results may vary based on the legibility of text within the document.
Tools / Downloads
Get a copy of this page or view the extracted text.
Citing and Sharing
Basic information for referencing this web page. We also provide extended guidance on usage rights, references, copying or embedding.
Reference the current page of this Report.
George, H. C. Surface Machinery and Methods for Oil-Well Pumping, report, 1925; Washington D.C.. (https://digital.library.unt.edu/ark:/67531/metadc12407/m1/76/: accessed April 20, 2024), University of North Texas Libraries, UNT Digital Library, https://digital.library.unt.edu; crediting UNT Libraries Government Documents Department.